Installation Instructions

ManualsBrandsIHP ManualsFireplace & Wood Stove Tools & AccessoriesSuperior™ Manually Controlled Blower

Save this manual for future reference.

For more information, visit www.desatech.com

(Check your appliance owner’s manual for specic applications and additional instructions.)

Parts included with this kit:

Part No. Description Quantity

Blower with speed control and 6-foot cord. 1

Instruction Sheet 1

103650-01 Control Knob 1

103651-01 Lock Nut 1

M11084-38 #8 x 3/8" sheet metal screws 5

101629-01 Plastic Hole Bushings 2

101584-05 Wiring Diagram Decal 1

Tools Required

• Pliers

• Phillips Screwdriver

If any of these pieces are missing or damaged or if the installation instructions for your replace or

stove are not included in this manual, contact the dealer where you purchased this kit or DESA at

1-866-672-6040 for referral information.

WARNING: ELECTRICAL GROUNDING INSTRUCTIONS This

appliance is equipped with a three-prong (grounding) plug for your

protection against shock hazard and should be plugged directly into

a properly grounded three-prong receptacle.

FOR USE WITH:

FIREBOXES: (NL)FB32C, (NL)FB36C, FB42C, (NL)UV32C, CGFB32C AND

CGFB36C SERIES

VENT-FREE FIREPLACES: VSGF28, VYGF33, VTGF33, VCGF30, VSGF33,

FPV33, CGFP28, LFP33 SERIES AND (CG)EFP33 SERIES

DIRECT-VENT FIREPLACES: (E)BDV, BHDV, DVF(E)34, DVFH34, CDV AND

CHDV SERIES

STOVES: CSDBN, SDVB, MSDVB MSTD, CDV, S39T AND S26T SERIES

GA3750A BLOWER ACCESSORY INSTALLATION

INSTRUCTIONS

Summary of content (16 pages)

PAGE 1
GA3750A Blower Accessory Installation Instructions For Use With: Fireboxes: (NL)FB32C, (NL)FB36C, FB42C, (NL)UV32C, CGFB32C and CGFB36C Series Vent-Free Fireplaces: VSGF28, VYGF33, VTGF33, VCGF30, VSGF33, FPV33, CGFP28, LFP33 Series and (CG)EFP33 Series Direct-Vent Fireplaces: (E)BDV, BHDV, DVF(E)34, DVFH34, CDV and CHDV Series Stoves: CSDBN, SDVB, MSDVB MSTD, CDV, S39T and S26T Series WARNING: ELECTRICAL GROUNDING INSTRUCTIONS This appliance is equipped with a three-prong (grounding) plug for your protec
PAGE 2
Installing Blower Accessory in a 32" Firebox Notice: If a log set is currently installed in the firebox, disconnect log set from gas supply and remove from firebox. Contact a qualified service person to do this. 7. Place speed control against inner wall of front panel, pushing the plastic control shaft forward through the opening (see Figure 3). 8. While supporting speed control, secure control shaft with lock nut by pushing and turning lock nut with pliers clockwise until it is tight against front panel.
PAGE 3
Installing Blower Accessory in a 32" Firebox Continued 9. Plug in blower power cord. a. If your firebox is installed as a freestanding unit, determine whether the power cord will exit the left side or the right side of the firebox. Install 1 plastic bushing provided into the 1 1/2" hole in the floor support on the exit side. Install the second plastic bushing provided into the 1 1/2" hole in the outer casing through which the power cord will exit (see Figure 4).
PAGE 4
INSTALLING BLOWER ACCESSORY IN 36" OR 42" FIREBOX Continued a. Using a Phillips screwdriver, remove the screw and retainer bracket at the top of the brick liner panel on the left side. Carefully remove the left panel from the firebox (see Figure 6). b. Repeat the removal steps for the brick liner panel on the right side. c. Remove the screw and retainer bracket at the top of the brick liner panel at the rear of the firebox. IMPORTANT: Do not let panel fall after bracket has bee removed.
PAGE 5
108319-01D Plastic Bushing Plastic Hole Plug 1 1/2" Hole Figure 10 - Installing Plastic Bushing for Power Cord Speed Control Control Shaft Locknut Control Knob Figure 11 - Attaching Speed Control to Firebox Floor Supports 110 V.A /115 .C. Blac Wh Gre ite k en Off Bla ck 5. Place the blower against the lower rear wall of the firebox outer wrapper with the exhaust port directed upward. Align the holes in top mounting tabs of blower with holes in wall of wrapper (see Figure 9, page 4).
PAGE 6
INSTALLING BLOWER ACCESSORY IN 36" OR 42" FIREBOX Continued 14. Replace and reattach firebox bottom using 4 screws removed in step 2 (see Figure 8, page 4). 15. If previously removed, carefully replace the firebrick side panels and/or floor in the firebox (see Figure 5, page 3 and Figures 6 and 7, page 4). 16. Install the log set heater according to the installation instructions supplied with the heater. WARNING: A qualified service person must install heater. Follow all local codes.
PAGE 7
Installing Blower Accessory in Model SVFBC Freestanding Stove Continued 11. Attach the terminal end of the green power cord wire to the front tab of the blower housing using screw provided (see Figure 14, page 6). 12. Using the four screws previously removed, mount blower assembly to stove by reattaching blower brackets to rear panel (see Figure 16). Tighten screws securely. 13. Install plastic control knob onto output shaft of speed control housing (see Figure 17).
PAGE 8
Installing Blower Accessory in Model SVFBC Freestanding Stove Continued 19. Using speed control knob, turn blower on and check for operation. 20. All remaining parts from blower kit may be discarded. Operating the Blower Light your gas appliance with the blower off. After about 15 minutes, turn the blower on to deliver heated air at the top louvers. The blower features a variable control which allows you to select the speed you desire. Installing Blower Accessory in 32” Fireplace systems 4.
PAGE 9
Installing Blower Accessory in 32" Fireplace systems Continued 9. Mount the speed control on the front leg of the left floor support bracket using 2 screws provided (see Figure 21). Note: Some remote ready fireplace models have the gas control located near the left floor support bracket. For these models, mount the blower speed control onto the right floor support bracket. 10. Plug in blower power cord. a.
PAGE 10
Installing Blower Accessory in 32" Fireplace systems Continued 16. Connect gas supply to fireplace per instructions in operating manual provided with fireplace. WARNING: A qualified service person must connect fireplace to gas supply. Follow all local codes. WARNING: Never attempt to service heater while it is plugged in, operating or hot. Burns and electrical shock could result. Only a qualified service person should service or repair heater.
PAGE 11
Installing blower accessory IN freestanding stove series SDV, MSD, MSTD, CDV OR CSDBN Control Shaft Speed Blower Control Control Knob Continued 7. Place speed control on left inside of rear cover and push the plastic control shaft through opening (see Figure 25). 8. While supporting speed control, secure control shaft with lock nut by pushing and turning lock nut with pliers clockwise until tight against the side of rear cover. Place control knob provided onto shaft (see Figure 25). 9.
PAGE 12
Installing blower accessory in directvent FIREPLACE series bhdv, (E)bdv, ddv, hdv, CDV, CHDV, DVF(E) or DVFH IMPORTANT: Read all installation instructions before installing blower. NOTICE: Shut off gas supply and disconnect heater from gas supply. Contact a qualified service person to do this. IMPORTANT: For clarity, gas valve assembly and grate/burner assembly are not shown in Figures 24 and 25. They will, however, be in your fireplace when you are installing the blower.
PAGE 13
Installing blower accessory in directvent FIREPLACE series bhdv, (E)bdv, ddv, hdv, CDV, CHDV, DVF(E) or DVFH Continued b. If your fireplace system installation is recessed and/or pre-wired, a qualified installer must make all electrical connections for the outlet kit included with the fireplace. 11. Check to make sure that the power cord is completely clear of the blower wheel and that there are no other foreign objects in blower wheel. Turn blower on and check for operation.
PAGE 14
NOTES ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ __________
PAGE 15
NOTES ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ __________
PAGE 16
2701 Industrial Drive, P.O. Box 90004 Bowling Green, KY 42102-9004 Technical Service Department 1-866-672-6040 www.desatech.com 108319 01 NOT A UPC 108319-01 Rev.