Installation Guide

ManualsBrandsiio ManualsAppliancesProfessional Series 24 in. 4 Elements Built In Electric Range in Black with Convection Oven

Prop. 65 Warning for California Residents

WARNING: This product may contain chemicals known to the State of

California to cause cancer, birth defects, or other reproductive harm.

Dispose of properly in accordance with federal and/or local regulations.

In case of punctured tubing follow all handling instructions carefully.

INSTALLATION

WARNING

➢ Product label is on the front of the oven.

➢ Never attempt to operate this appliance if it is damaged, malfunctioning, partially

disassembled, or has missing or broken parts, including a damaged cord or plug.

➢ Do not remove the ground prong from the power cord.

➢ Do not install using an extension cord.

➢ Do not use an adapter on the wall socket.

➢ Do not pull out the plug using the power cord. Firmly grasp the plug and pull it out

from the socket.

➢ When moving the appliance, be careful not to roll, bend, pinch or damage the

power cord.

➢ Do not install the appliance in a damp or dusty place where insulation or electrical

parts may deteriorate.

➢ Do not place electrical appliances on top of the appliance.

➢ Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive

cleaners to remove tape or glue. These products can damage the surface of your

appliance.

➢ Be sure your appliance is properly installed and grounded by a qualified technician.

In the United States, install in accordance with the National Fuel Gas Code ANSI

Z223.1/NPFA No. 54, latest edition, and National Electrical Code NFPA No. 70

latest edition, and local electrical code requirements. In Canada, install in

accordance with CAN/CGA B149.1 and CAN/CGA B149.2 and CSA Standard

C22.1, Canadian Electrical code, Part 1-latest editions and local electrical code

requirements. Install only per installation instructions provided in the literature

package for this appliance.

CAUTION

➢ Remove all tape and packaging before using the appliance. Destroy the carton and

plastic bags after unpacking the appliance.

➢ Do not remove the wiring label and other literature attached to the appliance.

Summary of content (8 pages)

PAGE 1
Prop. 65 Warning for California Residents WARNING: This product may contain chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. Dispose of properly in accordance with federal and/or local regulations. In case of punctured tubing follow all handling instructions carefully. INSTALLATION WARNING ➢ Product label is on the front of the oven.
PAGE 2
➢ Do not remove model/serial number plate. ➢ Cold temperatures can damage the electronic control. When using this appliance for the first time, or when the appliance has not been used for an extended period of time, be sure the appliance has been in temperatures above 32ºF (0ºC) for at least 3 hours before turning on the power to the appliance. ➢ Do not use an outlet that can be turned off with a switch. ➢ Install the appliance in a dry and well ventilated room.
PAGE 3
• • • • • • After removing the packaging material from the appliance and its accessories, ensure that the appliance is not damaged. If you suspect any damage, do not use it, and contact an authorised service person or qualified technician immediately. Make sure that there are no flammable or combustible materials in the close vicinity, such as curtains, oil, cloth etc. which may catch fire. The worktop and furniture surrounding the appliance must be made of materials resistant to temperatures above 215°F.
PAGE 4
Prepare The Electrical Connection: • • • Effective January 1, 1996 the National Electric Code requires that new construction (not existing) utilize a 4-conductor connection to an electric range. When installing an electric range in new construction follow Steps 3 and 5 for 4-wire connection. Use only a 3-conductor or a 4-conductor UL-listed range cord. These cords may be provided with ring terminals on wire and a strain relief device.
PAGE 5
3-Wire Power Cord Installation WARNING: The neutral or ground wire of the power cord must be connected to the neutral terminal located in the center of the connector block. The power leads must be connected to the outside (brass colored) terminals. • • Remove the 3 wire terminal screws from the connector block. Insert screws through each power cord terminal ring and into the connector block until the screws engage the nuts.
PAGE 6
WARNING: The neutral wire of the supply circuit is connected to the neutral terminal located in the center of the connector block. The power leads must be connected to the outside (brass colored) terminals. The 4th grounding lead must be connected to the frame of the range with the grounding plate and grounding screw. • • • • a) Remove the 3 screws from the connector block. b) Remove the grounding screw and strap from the connector block middle location and the screw connection to the frame of the range.
PAGE 7
Adjusting The Feet • • Your product stands on four adjustable feet. For safe operation, it is important that your appliance is correctly balanced. Make sure the appliance is level prior to cooking. To increase the height of the appliance, turn the feet anti-clockwise. To decrease the height of the appliance, turn the feet clockwise. It is possible to raise the height of the appliance up to 30 mm by adjusting the feet. The appliance is heavy and we recommend that a minimum of 2 people lift it.
PAGE 8
Dimensions and Clearances • • • Check the dimensions of the appliance and the installation path to ensure there is sufficient room to move the appliance through doors or narrow openings. The installation location chosen for the appliance should allow space behind the unit for connections and airflow as well as space in front to open the doors. Too small of a distance from adjacent items may result in reduced cooling and freezing capability and increased power consumption.