AQU5611D BK AQU5611DT BK 9.
First Edition (July 2002) © Copyright IIYAMA CORPORATION 2002. All rights reserved.
Danger Statements DANGER To avoid shock hazard: v Do not remove the covers. v Do not operate this product unless the stand is attached. v Do not connect or disconnect this product during an electrical storm. v The power cord plug must be connected to a properly wired and grounded power outlet. v Any equipment to which this product will be attached must also be connected to properly wired and grounded power outlets.
iv AQU5611D BK/AQU5611DT BK 9.
Notices Attention v Do not exert strong pressure to the surface of the monitor screen. You may break the LCD panel. v Do not place heavy objects on top of this product. They may damage the monitor. v Do not touch the monitor screen with your fingers. Fingerprints and oil stains may remain on the screen surface. They are difficult to wipe off. v The monitor is heavy. Ask the help of others if you cannot carry it by yourself.
License inquiries References in this publication to iiyama products, programs, or services do not imply that iiyama intends to make these available in all countries in which iiyama operates. Any reference to an iiyama product, program, or service is not intended to state or imply that only iiyama product, program, or service may be used.
Contents Danger Statements . . . . . . . . . . . . . . . . . . . . . . . iii Notices . . . . . . . . . . . . . Attention . . . . . . . . . . . . . LCD considerations. . . . . . . . . Considerations on the monitor resolution . Operating considerations . . . . . . . License inquiries . . . . . . . . . Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Industry Canada Class A Emission Compliance Statement . . Avis de Conformité à la Réglementation d’Industrie Canada . Deutsche EMV-Direktive (electromagnetische Verträglichkeit) . European Union – EMC Directive . . . . . . . . . . . Union Européenne – Directive Conformité électromagnétique . Union Europea – Normativa EMC . . . . . . . . . . . Europese Unie -- EMC-richtlijnen . . . . . . . . . . . Europeiska Unionen - EMC Direktiv . . . . . . . . . . Statements for Other Countries . . . . . . . . . . . .
Chapter 1. Before setting up This manual contains information on how to set up and operate the AQU5611D BK/AQU5611DT BK 9.2 Million Pixels Color TFT LCD Monitor, hereafter called the monitor. This chapter describes the following: v Prerequisites v Unpacking v Checking parts Prerequisites You will need a personal computer or a workstation (hereafter called the computer) with the following. v A Dual DVI output compliant video graphics card (hereafter simply called the DVI) Refer to http://www.iiyama.co.
Checking parts Check the box for the following items. If any items are missing or damaged, contact your place of purchase immediately. h Monitor h USER MANUAL (This book) h Connector tool h Power adapter and cord h Power cord h Digital signal cable P/N: 07N2227 Note: The digital signal cable is shipped with one end connected to the monitor. 2 AQU5611D BK/AQU5611DT BK 9.
Chapter 2. Hardware setup This chapter describes the following: v The location of the controls, switches, and connectors. v The procedure for setting up the monitor.
Setup the monitor Storing the connector tool This section describes how to store the connector tool for future use. This tool will be useful when disconnecting the cables from the monitor. Attention: 1. Remove any objects from the surface before tilting the monitor. They might damage your screen. 2. Be careful not to pinch your fingers between the monitor and the surface when tilting the monitor. To store the connector tool, do the following: 1. Clear a work space, and turn the monitor face down. 2.
3. Remove the connector cover. 1 Connector cover 2 2 4. Unhook the digital signal cable from the cable hook and lift it up to store the connector tool to the rear compartment of the monitor. Cable hook Connector tool Chapter 2.
Connecting the cables This section describes how to connect the following cables: 1. Power adapter cord 2. Digital signal cable 3. Power cord Connecting the power adapter cord 1. Connect the power adapter cord to the DC-IN connector at the rear of the monitor. Make sure that it clicks firmly into the connector. p To vie w Video connector DC-IN connector Bo tt om vi ew Note: The video connectors A and B on the monitor are Safety Extra Low Voltage (SELV) circuits. 2.
3. Reinstall the connector cover on the monitor. 2 Connector cover 1 1 4. Reinstall the stand rear cover and turn the monitor to the upright position. Stand rear cover Note: Do not power on the monitor or the computer until instructed. Failing to do so may damage these units or the video graphics card. Chapter 2.
Connecting the digital signal cable 1. 2. 3. 4. Make sure that the video graphics card is installed on your computer. Make sure that the power cord is NOT connected to your computer. Open the cover of your computer, if necessary. Connect the connector end marked ″1 PRIMARY″ to the DVI port marked ″1″, and the connector end marked ″2 SECONDARY″ to the DVI port marked ″2″ of the video graphics card. 5. If you have opened the cover of your computer, close it. Notes: a.
Connecting the power cord Note: Read the respective ″Danger Statements″ on pages iii before continuing with this section. 1. Connect the power cord to the power adapter. 2. Connect the power plug to a properly grounded power outlet. Note: Make sure that all the cables are connected, otherwise the power-on light will not turn on. 3. Connect the computer to a properly grounded power outlet and turn on the power switch. Chapter 2.
4. Press the power switch on the monitor. The power light comes on. Power switch Power lighit Notes: a. When you turn off the monitor, wait at least five seconds before turning it on again. b. If you accidentally disconnected the power cord from the main outlet and you connected it to the outlet again, the screen may flicker continuously. To stop the flicker, press the power switch and turn off the monitor, then turn it on again. c.
Chapter 3. Adjusting and maintaining your monitor This chapter describes the following: v How to adjust the viewing angle. v How to set the controls. v The operating status of your monitor. v How to disconnect the cables. v How to use the security keylock. v How to maintain your monitor. Adjusting the viewing angle You can adjust the vertical angle of the monitor to avoid unnecessary light reflection and to make viewing easier.
Setting the monitor control buttons You can control the various functions of the monitor using the buttons at the front right of the monitor. The four buttons control the following functions: Button/ Button Name Direct access functions Functions available from the OSD Menu Displays the on-screen display (OSD) menu. Enters highlighted menu mode. Sets the screen to a dimmer view. Moves the cursor to the left for highlighting the icons or for making adjustments. Sets the screen to a brighter view.
Accessing the on-screen display (OSD) menus You can access the on-screen display (OSD) menus by pressing the Menu/Enter button. The OSD menus enable you to set the various operating conditions of your monitor.
Submenus To access a submenu, do the following: submenu Brightness 1. Select the Brightness icon on the Main menu using the Left-Arrow or the Right-Arrow button 2. Press the Menu/Enter button. The Brightness submenu appears. 3. Adjust the brightness using the Left-Arrow or the Right-Arrow button. 4. Press the Menu/Enter button to exit from this submenu. submenu Video input 1. Select the Video Input icon on the Main menu using the Left-Arrow or the Right-Arrow button. 2. Press the Menu/Enter button.
OSD Icon Description One video input mode. Two video input mode. (The color management function is always effective.) Four stripes video input mode. (The color management function is always effective.) Four tiles video input mode. (The color management function is always effective.) Exit from the Submenu. 1 or 0 (to the left of the numbers) Sets the color management function or the smooth character display function.
Knowing the operating status of your monitor You can know the status of your monitor by the color of the power light. Power light The color of the power light changes from green to amber when your monitor receives a time-out video signal from the computer and enters Standby mode to save power. A time-out video signal is sent from your computer to the monitor when the former detects inactivity on the keyboard or mouse for a set duration of time.
Disconnecting the cable CAUTION: Do not use a digital signal cable other than the one shipped with the product. Using some other cable may damage the monitor or the video graphics card. The cable (P/N: 07N2227) is available at iiyama Customer Support Line (refer to page 21). Note: Before you begin the procedures below, be sure to read the “Danger Statements” on page iii. To disconnect the digital signal cable, do the following: 1.
Using the security keylock The monitor has a built-in security keyhole at the rear of the screen for fastening a security lock and cable. This lock is used to help prevent the monitor from being removed without your permission. This cable can be purchased at any PC shop. First secure the cable to a stationary object; then attach the lock to the keyhole on the rear of the monitor. For details of the installation, refer to the instructions shipped with the security keylock.
Chapter 4. Troubleshooting Is something wrong? If you suspect that something is not working correctly, you should: 1. Turn on the computer and monitor. 2. 3. 4. 5. ) to the proper position. Set the brightness control ( Make sure that all cables are securely connected. Disable the computer’s screen saver program, if it is enabled. Set the display mode to the supported display mode. 6. If you still have a problem, go to the symptom list below and find the symptom that most resembles yours.
The screen is blank The display mode of the and the power indicator computer is outside the is blinking amber every range of the monitor second v Reconfigure the computer to use a supported display mode. v The video graphics card is defective. Replace it. v The computer is defective. Replace it. The screen is blank The monitor fan is not and the power indicator working is blinking amber every 0.25 second v Make sure that the power cord is firmly plugged into the electrical outlet.
Warranty information Machine Name: AQU5611D BK/AQU5611DT BK 9.2 Million Pixels Color TFT LCD Monitor Warranty Period: One (1) Year Service and support The terms and conditions of the services are described on the Warranty sheet. For services, contact the Service Center listed on the Warranty sheet or contact your dealer. Before calling, please have available as much of the following information as possible: 1. 2. 3. 4. 5. 6. Type, model, and serial number from the label on the back of your monitor.
22 AQU5611D BK/AQU5611DT BK 9.
Appendix A. Specifications The specifications of the monitor are as follows: Dimensions Width: Height: Depth: Depth (without stand): 547 439 196 105 mm mm mm mm (21.5 in.) (17.3 in.) (7.7 in.) (4.1 in.) Weight Unpackaged: With base stand: 11.4 kg (25.1 lb.) Power adapter: 1.3 kg (2.9 lb.
Supported display modes The monitor supports the following display modes: DVI Input Horizontal Frequency (KHz) Vertical Frequency (Hz) Dot Clock Frequency (MHz) Actual Display Resolution 640 × 400 ch1 31.5 (N, P) 59.9 (N, P) 25.2 3200 × 2000 640 × 480 ch1 37.9 (N, P) 72.8 (N, P) 31.5 3200 × 2400 640 × 480 ch1 37.5 (N, P) 75.0 (N, P) 31.5 3200 × 2400 640 × 480 ch1 43.3 (N, P) 85.0 (N, P) 36.0 3200 × 2400 800 × 600 ch1 35.2 (P, N) 56.3 (P, N) 36.
Updating the settings for your monitor Unless you change the video graphics card that drives your monitor, there is usually no need to change the settings. In case the need does arise, a procedure for changing them is given in this appendix. This operation must be done carefully. If incorrect parameters are specified, nothing will be displayed. Applicable models The procedure given in this document applies to monitors with firmware at the following levels: DDC CPU Version 3.
2. Enabling the special OSD (on-screen display) menu a. Press a menu switch and either the left switch or the right switch to select the (i) (information) menu. On that menu, press the menu switch to enter the information menu. There, a display showing the refresh rate and the screen resolution appears, as in this example: 1600 1200 b. Press the left switch three times, and then press the right switch three times. Page 1 of the special OSD menu appears, as in this example: -1- 3.2 5.
If the setting is given as 000, any number greater than 63, or a value ending in X, an error has occurred; try step 3 on page 26 again. For details, see “Valid settings” on page 28. 4. Updating the settings a. From the table on page 28, choose the number of the settings you want to use. b. Set the brightness parameter to the value for the settings you have chosen (see “Brightness submenu” on page 14.).
Valid settings DDC-CPU version 3.2 can detect and update some settings. If it encounters any it does not recognize, it reads them as 000 (unknown). From the following table, choose the settings that are appropriate for the operating system and video graphics card you are using. If you want to use settings not listed in the table, consider upgrading to another version of DDC-CPU. Settings are sometimes updated without notice. For the latest information, refer to http://www.iiyama.co.
Appendix B. Field–Replaceable Units (FRUs) 1 4 3 2 No.
30 AQU5611D BK/AQU5611DT BK 9.
Appendix C. Compliance TCO’95 Congratulations! You have just purchased a TCO’95 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products.
The environmental demands impose restrictions on the presence and use of heavy metals, brominated and chlorinated flame retardants, CFCs (freons) and chlorinated solvents, among other things. The product must be prepared for recycling and the manufacturer is obliged to have an environmental policy which must be adhered to in each country where the company implements its operational policy.
Mercury Mercury is sometimes found in batteries, relays and switches. Mercury damages the nervous system and is toxic in high doses. TCO’95 requirements states that batteries may not contain more than 25 ppm (parts per million) of mercury. It also demands that no mercury is present in any of the electrical or electronics components concerned with the display unit.1 CFSc (freons) CFCs (freons) are sometimes used for washing printed circuit boards and in the manufacturing of expanded foam for packaging.
Dieses Gerät erfüllt die Bedingungen der EN 55022 Klasse A. Für diese Klasse von Geräten gilt folgende Bestimmung nach dem EMVG: Geräte dürfen an Orten, für die sie nicht ausreichend entstört sind, nur mit besonderer Genehmigung des Bundesminesters für Post und Telekommunikation oder des Bundesamtes fur Post und Telekommunikation betrieben werden. Die Genehmigung wird erteilt, wenn keine elektromagnetischen Störungen zu erwarten sind. (Auszug aus dem EMVG vom 9.Nov.92, Para.3. Abs.
Union Europea – Normativa EMC Questo prodotto è conforme alle normative di protezione ai sensi della Direttiva del Consiglio dell’Unione Europea 89/336/CEE ull’armonizzazione legislativa degli stati membri in materia di compatibilità elettromagnetica. iiyama non accetta responsabilità alcuna per la mancata conformità alle normative di protezione dovuta a modifiche non consigliate al prodotto, compresa l’installazione di schede e componenti di marca diversa da iiyama.
kommunikationsutrustning. Varning: Detta är en Class A produkt. I hemmiljö kan produkten orsaka radiostörningar, som kräver att användaren vidtager nödvändiga åtgärder. Statements for Other Countries Power Cord For your safety, iiyama provides a power cord with a grounded attachment plug to use with this iiyama product. To avoid electrical shock, always use the power cord and plug with a properly grounded power outlet.
Hinweise Gemäβ der Amtsblätter des BMPT Nm. 61/1991 und 6/1992 wird der Betreiber darauf aufmerksam gemächt, daβ die von ihm mit diesem Gerät zusammengestellte Anlage auch den technischen Bestimmungen dieser Amtsblätter genügen muβ. Aus ergonomischen Gründen wird empfohlen, die Grundfarbe Blau nicht auf dunklem Untergrund zu verwenden (schlechte Erkennbarkeit, Augenbelastung bei zu geringem Zeichenkontrast).
38 AQU5611D BK/AQU5611DT BK 9.
