USER MANUAL ENGLISH Thank you very much for choosing the iiyama LCD monitor. We recommend that you take a few minutes to read carefully through this brief but comprehensive manual before installing and switching on the monitor. Please keep this manual in a safe place for your future reference.
ENGLISH
Congratulations! for Sustainable IT TCO Certified is an international third party sustainability certification for IT products. TCO Certified ensures that the manufacture, use and recycling of IT products reflect environmental, social and economic responsibility. Every TCO Certified product model is verified by an accredited independent test laboratory.
CE MARKING DECLARATION OF CONFORMITY ENGLISH This LCD monitor complies with the requirements of the EC/EU Directive 2004/108/EC “EMC Directive”, 2006/95/EC “Low Voltage Directive”, 2009/125/EC “ErP Directive” and 2011/65/EU “RoHS Directive”. The electro-magnetic susceptibility has been chosen at a level that gives correct operation in residential areas, business and light industrial premises and small-scale enterprises, inside as well as outside of the buildings.
FOR YOUR SAFETY..........................................................................1 SAFETY PRECAUTIONS..............................................................1 SPECIAL NOTES ON LCD MONITORS .......................................3 CUSTOMER SERVICE .................................................................3 CLEANING ....................................................................................3 BEFORE YOU OPERATE THE MONITOR ........................................4 FEATURES........
FOR YOUR SAFETY SAFETY PRECAUTIONS WARNING If you notice any abnormal phenomena such as smoke, strange sounds or fumes, unplug the monitor and contact your dealer or iiyama service center immediately. Further use may be dangerous and can cause fire or electric shock. NEVER REMOVE THE CABINET High voltage circuits are inside the monitor. Removing the cabinet may expose you to the danger of fire or electric shock.
CAUTION INSTALLATION LOCATION Do not install the monitor where sudden temperature changes may occur, or in humid, dusty or smoky areas as it may cause fire, electric shock or damage. You should also avoid areas where the sun shines directly on the monitor. DO NOT PLACE THE MONITOR IN A HAZARDOUS POSITION ENGLISH The monitor may topple and cause injury if not suitably located.
SPECIAL NOTES ON LCD MONITORS NOTE When you first turn on the LCD monitor, the picture may not fit in the display area because of the type of computer that is used. In this case, adjust the picture position to the correct position. Due to the nature of the backlight, the screen may flicker during initial use. Turn off the Power Switch and then turn it on again to make sure the flicker disappears. You may find slightly uneven brightness on the screen depending on the desktop pattern you use.
BEFORE YOU OPERATE THE MONITOR FEATURES Supports Resolutions up to 1280 × 1024 2 High Contrast 1000:1 (Typical) , ACR Function Available / Brightness 250cd/m (Typical) / Quick Response Time 5ms (Typical) ENGLISH Digital Character Smoothing Automatic Set-up Stereo Speakers 2 × 1W Stereo Speakers Plug & Play VESA DDC2B Compliant Windows® XP/Vista/7/8 Compliant ® Power Management (ENERGY STAR VESA DPMS Compliant) Ergonomic Design: TCO Certified Compliant VESA Mounting Standard (100mm×100mm
FITTING AND REMOVAL OF BASE : ProLite B1706S The monitor is supplied complete with a stand-base. If you prefer to wall mount the monitor, please follow the instructions below to remove the stand-base. Be sure to include the stand with the monitor if it is necessary to return the unit. A Put a piece of soft cloth on the table beforehand to prevent the monitor from being scratched. Lay the monitor flat on a table with front face down. B Install the Stand-Base to the Monitor.
FITTING AND REMOVAL OF BASE : ProLite E1706S CAUTION Install the stand on a stable surface. The monitor may cause injury or damage if it falls or is dropped. Do not give a strong impact to the monitor. It may cause damage. Unplug the monitor before installation to avoid electric shock or damage. ENGLISH A Put a piece of soft cloth on the table beforehand to prevent the monitor from being scratched. Lay the monitor flat on a table with front face down.
ENGLISH CONTROLS AND CONNECTORS : ProLite B1706S A Power Switch ( ) B Menu / Select Button (MENU) C + / Volume Button ( + ) D - / ECO Button ( - ) E Auto Button (AUTO) F Power Indicator NOTE Blue: Normal operation Orange: Power Management G Speakers H D-SUB mini 15pin Connector (D-SUB) I DVI-D 24pin Connector (DVI-D) J Cable Holder K Audio Connector (AUDIO IN) L AC Connector (AC IN) M Keyhole for Security Lock NOTE You can fasten a security lock and cable to prevent the monitor from being
ENGLISH CONTROLS AND CONNECTORS : ProLite E1706S A Power Switch ( ) B Menu / Select Button (MENU) C + / Volume Button ( + ) D - / ECO Button ( - ) E Auto Button (AUTO) F Power Indicator NOTE Blue: Normal operation Orange: Power Management G Speakers H D-SUB mini 15pin Connector (D-SUB) I DVI-D 24pin Connector (DVI-D) J Audio Connector (AUDIO IN) K AC Connector (AC IN) L Keyhole for Security Lock NOTE You can fasten a security lock and cable to prevent the monitor from being removed withou
CONNECTING YOUR MONITOR : ProLite B1706S NOTE The signal cables used for connecting the computer and monitor may vary with the type of computer used. An incorrect connection may cause serious damage to both the monitor and the computer. The cable supplied with the monitor is for a standard 15 pin D-Sub connector. If a special cable is required please contact your local iiyama dealer or regional iiyama office.
CONNECTING YOUR MONITOR : ProLite E1706S ENGLISH A Ensure that both the computer and the monitor are switched off. B Connect the computer to the monitor with the signal cable. C Connect the monitor to the audio equipment with the Audio Cable for computer when using the audio features. D Connect the Power Cable to the monitor first and then to the power supply. E Power of the monitor and the computer is turned on.
COMPUTER SETTING Signal Timing Change to the desired signal timing listed on page 29: COMPLIANT TIMING. ADJUSTING THE VIEWING ANGLE : ProLite E1706S NOTE Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen. Careful attention is required not to catch your fingers or hands when you change the angle. ENGLISH For optimal viewing it is recommended to look at the full face of the monitor.
ENGLISH ADJUSTING THE HEIGHT AND THE VIEWING ANGLE : ProLite B1706S For optimal viewing it is recommended to position yourself directly opposite to the full face of the monitor, then adjust the monitor’s height and angle to your own preference. Hold the panel so that the monitor does not topple when you change the monitor’s height or angle. You are able to adjust the monitor's height up to 110mm, angle up to 170 degrees right and left, 20 degrees upward.
OPERATING THE MONITOR To create the best picture, your iiyama LCD monitor has been preset at the factory with the COMPLIANT TIMING shown on page 29. You are also able to adjust the picture by following the button operation shown below. For more detailed adjustments, see page 20 for SCREEN ADJUSTMENTS. Press the MENU Button to start the On Screen Display feature. There are additional Menu items which can be switched by using the + / - Buttons.
ADJUSTMENT MENU CONTENTS Luminance Luminance Contrast 50 Brightness 50 Eco Off Picture Mode ON ENGLISH ACR Adjustment Item Problem / Option Contrast Too dull Too intense Brightness * Too dark Too bright Eco Off Mode1 Mode2 Mode3 Direct Picture Mode Standard Button to Press Normal Brightness of back-light is reduced. Brightness of back-light is reduced more than Mode1. Brightness of back-light is reduced more than Mode2.
Image Setup Image Setup Adjustment Item Clock* Phase* Clock 50 Phase 50 H.Position 50 V.Position 50 Problem / Option Button to Press ENGLISH Only Analog Input Too narrow Too wide To correct flickering text or lines H. Position Too left Too right V. Position Too low Too high * See page 20 for SCREEN ADJUSTMENTS.
Color Temp. Color Temp. Gamma Mode1 Color Temp. Warm 50 User-R ENGLISH Adjustment Item Gamma Color Temp. User-G 50 User-B 50 Problem / Option Mode1 Mode2 Mode3 Normal Dark High contrast User-R User User-G User-B Cool Normal Warm Bluish white Yellowish white Greenish white sRGB sRGB Button to Press Too weak Too strong sRGB is an international standard which defines and unifies the difference of color NOTE appearance between equipment.
OSD Setup OSD Setup H.Position 50 V.Position 50 Timeout 50 Language Problem / Option Button to Press ENGLISH Adjustment Item English H.Position OSD is too left OSD is too right V.Position OSD is too low OSD is too high Timeout You can set the OSD display duration time between 5 and 60 seconds.
Others Others Reset Yes Signal Select Auto Information Resolution : H.Frequency : V.Frequency : ENGLISH Adjustment Item 800(H)*600(V) 38KHz 60Hz Problem / Option Yes Button to Press Factory-preset data is restored. Reset Signal Select Direct No Return to Menu. Auto D-sub DVI-D Select the signal input automatically. Select the Analog input. Select the Digital input.
Direct You can skip the Menu items and display an adjustment scale directly by using the following button operations. Volume: Press the + Button when the Menu is not displayed. Volume Problem / Option Button to Press Too soft Too loud ENGLISH Adjustment Item Auto Adjust: Press the Auto Button when the Menu is not displayed. Only Analog Input Adjustment Item Auto Adjust * Problem / Option Button to Press Adjust H. / V. Position, Clock and Phase automatically.
SCREEN ADJUSTMENTS Adjust the image by following the procedure below to get the desired picture when selecting Analog input. The screen adjustments described in this manual are designed to set image position and minimize flicker or blur for the particular computer in use. The monitor is designed to provide the best performance at resolution of 1280 × 1024, but can not provide the best at resolutions of less than 1280 × 1024 because the picture is automatically stretched ENGLISH to fit the full screen.
C Press the Auto Button. (Auto Adjust) D Adjust the image manually by following procedure below when the screen has a flicker or blur, or the picture does not fit in the display area after performing the Auto Adjust. ENGLISH E Adjust the V.Position so that the top and bottom of the picture frame will fit to the display area. F 1) Adjust the H.Position so that the left side of the picture frame will move to the left edge of the display area.
ENGLISH G Adjust the Phase to correct horizontal wavy noise, flicker or blur in the zebra pattern. NOTE In case the strong flicker or blurs remain on a part of the screen, repeat steps F and G because the Clock may not be adjusted correctly. If the flicker or blurs still remain, set the refresh rate of computer to low (60Hz) and repeat steps from C again. Adjust the H.Position after the Phase adjustment if the horizontal position moves during the adjustment.
POWER MANAGEMENT FEATURE Power Management Mode When the H-sync signal / V-sync signal / H and V sync signals from the computer are off, the monitor enters into Power Management Mode which reduces the power consumption to less than 0.5W. The screen becomes dark, and the power indicator turns to orange. From Power Management Mode, the image reappears in several seconds when either the keyboard or the mouse are touched again. Power Indicator NORMAL MODE POWER MANAGEMENT MODE Blue Orange POWER 0 0.
TROUBLE SHOOTING If the monitor fails to operate correctly, please follow the steps below for a possible solution. ENGLISH 1. Perform the adjustments described in OPERATING THE MONITOR, depending on the problem you have. If the monitor does not get a picture, skip to 2. 2. Consult the following items if you cannot find an appropriate adjustment item in OPERATING THE MONITOR or if the problem persists. 3.
Problem The audio equipment (computer etc.) is ON. The Audio Cable is properly connected. The Volume is turned up. The Mute is OFF. The audio output level of the audio equipment is within the specification of the monitor. The audio output level of the audio equipment is within the specification of G The sound is too loud or too quiet. the monitor. The Audio Cable is properly connected. H A strange noise is heard.
APPENDIX Design and specifications are subject to change without prior notice. SPECIFICATIONS : ProLite B1706S 17" LCD Panel Driving system a-Si TFT Active Matrix ENGLISH Size Category Size Diagonal: 17" (43cm) Pixel pitch 0.264mm H × 0.264mm V Brightness 250cd/m2 (Typical) Contrast ratio 1000 : 1 (Typical), ACR Function Available Viewable angle Right / Left : 85 degrees each, Up / Down: 80 degrees each (Typical) Response time 5ms (Black, White, Black) Display Colors Approx.16.
SPECIFICATIONS : ProLite E1706S LCD Panel Driving system Size 17" a-Si TFT Active Matrix Diagonal: 17" (43cm) Pixel pitch 0.264mm H × 0.264mm V Brightness 250cd/m2 (Typical) Contrast ratio 1000 : 1 (Typical), ACR Function Available Viewable angle Right / Left : 85 degrees each, Up / Down: 80 degrees each (Typical) Response time 5ms (Black, White, Black) Display Colors Approx.16.77M Sync Frequency Analog: Horizontal: 24.0-80.0kHz, Vertical: 55-75Hz Digital: Horizontal: 30.0-80.
DIMENSIONS : ProLite B1706S 371.5mm/14.6" 339.5mm/13.4" ENGLISH 249.5mm/9.8" 272.0mm/10.7" 323.0mm/12.7" 385.5mm/15.2" (495.5mm/19.5") 59.0mm/2.3" ( ): Maximum adjustment range DIMENSIONS : ProLite E1706S 371.5mm/14.6" 339.5mm/13.4" 28 APPENDIX 190.0mm/7.5" 382.5mm/15.1" 272.0mm/10.7" 323.0mm/12.7" 59.0mm/2.
COMPLIANT TIMING Vertical Frequency 59.940Hz 25.175MHz 37.500kHz 75.000Hz 31.500MHz 37.861kHz 72.809Hz 31.500MHz 35.156kHz 56.250Hz 36.000MHz 37.879kHz 60.317Hz SVGA 40.000MHz 46.875kHz 75.000Hz 49.500MHz 48.077kHz 72.188Hz 50.000MHz 48.363kHz 60.004Hz 65.000MHz 56.476kHz 70.069Hz 75.000MHz 60.023kHz 75.029Hz 78.750MHz 63.981kHz 60.020Hz 108.000MHz 79.976kHz 75.025Hz 135.000MHz 35.000kHz 66.667Hz 30.240MHz 832 × 624 49.725kHz 74.500Hz 57.