USER MANUAL ENGLISH DEUTSCH FRANCAIS NEDERLANDS Thank you very much for choosing the iiyama LCD monitor. We recommend that you take a few minutes to read carefully through this brief but comprehensive manual before installing and switching on the monitor. Please keep this manual in a safe place for your future reference. PLE2001_3WS_WSV-e-M034B01.
Congratulations! ENGLISH The display you have just purchased carries the TCO’03 Displays label. This means that your display is designed, manufactured and tested according to some of the strictest quality and environmental requirements in the world. This makes for a high performance product, designed with the user in focus that also minimizes the impact on our natural environment.
FCC DECLARATION OF CONFORMITY PL2000 iiyama Ampronix Inc. 8697 Research Dr. Irvine, CA.92618 U.S.A. 949-788-9930 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
ENGLISH TABLE OF CONTENTS FOR YOUR SAFETY .............................................................................. SAFETY PRECAUTIONS ................................................................. SPECIAL NOTES ON LCD MONITORS ............................................. CUSTOMER SERVICE ...................................................................... CLEANING ....................................................................................... 1 1 3 3 3 BEFORE YOU OPERATE THE MONITOR .
FOR YOUR SAFETY SAFETY PRECAUTIONS WARNING If you notice any abnormal phenomena such as smoke, strange sounds or fumes, unplug the monitor and contact your dealer or iiyama service center immediately. Further use may be dangerous and can cause fire or electric shock. NEVER REMOVE THE CABINET High voltage circuits are inside the monitor. Removing the cabinet may expose you to the danger of fire or electric shock.
CAUTION INSTALLATION LOCATION Do not install the monitor where sudden temperature changes may occur, or in humid, dusty or smoky areas as it may cause fire, electric shock or damage. You should also avoid areas where the sun shines directly on the monitor. ENGLISH DO NOT PLACE THE MONITOR IN A HAZARDOUS POSITION The monitor may topple and cause injury if not suitably located.
SPECIAL NOTES ON LCD MONITORS The following symptoms are normal with LCD monitors and do not indicate a problem. When you first turn on the LCD monitor, the picture may not fit in the display area because of the type of computer that is used. In this case, adjust the picture position to the correct position. Due to the nature of the backlight, the screen may flicker during initial use. Turn off the Power Switch and then turn it on again to make sure the flicker disappears.
BEFORE YOU OPERATE THE MONITOR FEATURES 51.1cm (20.
HOW TO USE THE STAND The monitor is shipped with the stand detached. Be sure to attach the stand before operating the display and remove if it is necessary to re-box. CAUTION Install the Stand on a stable surface. The monitor may cause injury or damage if it falls or is dropped. Do not give a strong impact to the monitor. It may cause damage. Unplug the monitor before installation to avoid electric shock or damage. ENGLISH 1 .
ENGLISH CONTROLS AND CONNECTORS FRONT PANEL CONTROL AUTO EXIT ENTER A Auto Button (AUTO) B Exit / Volume Button (EXIT) C Scroll Down / Contrast Button ( ) D Scroll Up / Brightness Button ( ) E Menu / Select Button (ENTER) F Power Switch ( ) G Headphone Connector H Power Indicator NOTE Green: Normal operation Orange: Power Management The monitor enters into power management mode which reduces the power consumption to less than 2W when receiving no horizontal and/or vertical sync s
CONNECTING YOUR MONITOR A Ensure that both the computer and the monitor are switched off. B Connect the computer to the monitor with the signal cable.(See page 25 for CONNECTOR PIN ASSIGNMENT.) C Connect the monitor to the audio equipment with the Audio Cable for computer when using the audio features. NOTE The signal cables used for connecting the computer and monitor may vary with the type of computer used. An incorrect connection may cause serious damage to both the monitor and the computer.
COMPUTER SETTING ENGLISH Signal Timing Change to the desired signal timing listed on page 24: COMPLIANT TIMING. Windows 95/98/2000/Me/XP/Vista Plug & Play The iiyama LCD monitor complies with DDC2B of VESA standard. The Plug & Play function runs on Windows 95/98/2000/Me/XP/Vista by connecting the monitor to DDC2B compliant computer with the Signal Cable supplied.
OPERATING THE MONITOR To create the best picture, your iiyama LCD monitor has been preset at the factory with the COMPLIANT TIMING shown on page 24. You are also able to adjust the picture by following the button operation shown below. For more detailed adjustments, see page 14 for SCREEN ADJUSTMENTS. ( Press the ENTER Button to start the On Screen Display feature. There are additional Menu items which can be switched by using the / Buttons.
ADJUSTMENT MENU CONTENTS Auto Adjust Only Analog Input Adjustment Item ENGLISH Auto Adjust * * Problem / Option Direct Button to Press Adjust H. / V. Position, Pixel Clock and Phase automatically. For best results, use the Auto Adjust in conjunction with the adjustment pattern. See page 14 for SCREEN ADJUSTMENTS. Direct You can skip the Menu items and display an adjustment scale directly by using the following button operations. z Auto Adjust: Press the Auto Button when the Menu is not displayed.
Only Analog Input Adjustment Item Problem / Option H. Position Too left Too right V. Position Too low Too high Pixel Clock Too narrow Too wide Button to Press ENGLISH Geometry To correct flickering text or lines Phase Color Adjustment Item Problem / Option 9300K Bluish white 7500K Yellowish white 6500K Reddish white User Preset Red Green Blue Button to Press Too weak Too strong OSD Adjustment Item Problem / Option Button to Press H.Position OSD is too left OSD is too right V.
Language Adjustment Item Problem / Option English Français Deutsch Italiano Polski ENGLISH Language Button to Press Español Spanish Nederlands Dutch Japanese English French German Italian Polish Simplified Chinese Russian Recall Adjustment Item Problem / Option Recall All Button to Press Yes Factory-preset data is restored. No Return to Menu. Miscellaneous Adjustment Item Problem / Option Button to Press 1 2 3 4 5 Sharpness You can change the picture quality from 1 to 5 (sharp to soft).
Miscellaneous Adjustment Item Problem / Option DCR Button to Press On Increased Contrast Ratio Off Typical Contrast Ratio OD You can set the OverDrive level between 0 and 5. It will improve the gray level response time of the LCD panel. A higher level results in a faster response time. Input Select Available for ProLite E2001WS / E2003WS only. Adjustment Item Problem / Option D-sub DVI Input Select NOTE Button to Press Select the Analog input. Select the Digital input.
SCREEN ADJUSTMENTS Adjust the image by following the procedure below to get the desired picture when selecting Analog input. The screen adjustments described in this manual are designed to set image position and minimize flicker or blur for the particular computer in use. ENGLISH The monitor is designed to provide the best performance at resolution of 1680 × 1050, but can not provide the best at resolutions of less than 1680 × 1050 because the picture is automatically stretched to fit the full screen.
C Press the Auto Button. (Auto Adjust) D Adjust the image manually by following procedure below when the screen has a flicker or blur, or the picture does not fit in the display area after performing the Auto Adjust. ENGLISH E Adjust the V.Position so that the top and bottom of the picture frame will fit to the display area. F 1) Adjust the H.Position so that the left side of the picture frame will move to the left edge of the display area.
G Adjust the Phase to correct horizontal wavy noise, flicker or blur in the zebra pattern. ENGLISH NOTE In case the strong flicker or blurs remain on a part of the screen, repeat steps F and NOTE G because the Pixel Clock may not be adjusted correctly. If the flicker or blurs still remain, set the refresh rate of computer to low (60Hz) and repeat steps from C again. Adjust the H.Position after the Phase adjustment if the horizontal position moves during the adjustment.
POWER MANAGEMENT FEATURE Power Management Mode When the H-sync signal / V-sync signal / H and V sync signals from the computer are off, the monitor enters into Power Management Mode which reduces the power consumption to less than 2W. The screen becomes dark, and the power indicator turns to orange. From Power Management Mode, the image reappears in several seconds when either the keyboard or the mouse are touched again.
TROUBLE SHOOTING If the monitor fails to operate correctly, please follow the steps below for a possible solution. 1. Perform the adjustments described in OPERATING THE MONITOR, depending on the problem you have. If the monitor does not get a picture, skip to 2. 2. Consult the following items if you cannot find an appropriate adjustment item in OPERATING THE MONITOR or if the problem persists. ENGLISH 3.
Problem Check The audio equipment (computer etc.) is ON. The Audio Cable is properly connected. The Volume is turned up. The Mute is OFF. The audio output level of the audio equipment is within the specification of the monitor. G The sound is too loud or too quiet. The audio output level of the audio equipment is within the specification of the monitor. H A strange noise is heard. The Audio Cable is properly connected. ENGLISH F No sound.
APPENDIX SPECIFICATIONS ProLite E2001WS ENGLISH LCD Panel Driving system a-Si TFT Active Matrix Size Diagonal: 51.1cm / 20.1" Pixel pitch 0.258mm H × 0.258mm V Brightness 250cd/m2 (Typical) Contrast ratio 1000 : 1 (Typical) Viewable angle Right / Left / Up / Down: 80 degrees each (Typical) Response time 5ms (Black, white, black) Display Colors Approx.16.2M (6bit+FRC dithering) Sync Frequency Horizontal: 31.0-83.
LCD Panel Driving system a-Si TFT Active Matrix Size Diagonal: 51.1cm / 20.1" Pixel pitch 0.258mm H × 0.258mm V Brightness 250cd/m2 (Typical) Contrast ratio 1000 : 1 (Typical) Viewable angle Right / Left / Up / Down: 80 degrees each (Typical) Response time ENGLISH ProLite E2001WSV 5ms (Black, white, black) Display Colors Approx.16.2M (6bit+FRC dithering) Sync Frequency Horizontal: 31.0-83.0kHz, Vertical: 56-75Hz Dot Clock 165MHz maximum Maximum Resolution 1680 × 1050, 1.
ProLite E2003WS ENGLISH LCD Panel Driving system a-Si TFT Active Matrix Size Diagonal: 51.1cm / 20.1" Pixel pitch 0.258mm H × 0.258mm V Brightness 300cd/m2 (Typical) Contrast ratio 1000 : 1 (Typical), 2000 : 1 (DCR) Viewable angle Right / Left / Up / Down: 85 degrees each (Typical) Response time 5ms (Typical), 2ms (Gray to Gray) Display Colors Approx.16.7M Sync Frequency Horizontal: 31.0-83.0kHz, Vertical: 56-75Hz Dot Clock 165MHz maximum Maximum Resolution 1680 × 1050, 1.
LCD Panel Driving system a-Si TFT Active Matrix Size Diagonal: 51.1cm / 20.1" Pixel pitch 0.258mm H × 0.258mm V Brightness 300cd/m2 (Typical) Contrast ratio 1000 : 1 (Typical), 2000 : 1 (DCR) Viewable angle Right / Left / Up / Down: 85 degrees each (Typical) Response time 5ms (Typical), 2ms (Gray to Gray) Display Colors Approx.16.7M Sync Frequency Horizontal: 31.0-83.0kHz, Vertical: 56-75Hz Dot Clock 165MHz maximum Maximum Resolution 1680 × 1050, 1.
DIMENSIONS DIMENSIONS 399.0mm/15.7" 188.0mm/7.4" 58.0mm/2.3" 273.0mm/10.7" 338.0mm/13.3" ENGLISH 480.0mm/18.9" 436.0mm/17.2" 226.0mm/8.9" COMPLIANT TIMING Video Mode VGA 640 × 480 SVGA 800 × 600 XGA WXGA 1280 × 768 Quad-VGA 1280 × 960 VESA SXGA VGA TEXT Macintosh NOTE 24 1024 × 768 1280 × 1024 WXGA+ 1440 × 900 WSXGA+ 1680 × 1050 720 × 400 832 × 624 1152 × 870 Horizontal Frequency Vertical Frequency Dot Clock 31.468kHz 37.500kHz 37.878kHz 46.875kHz 48.362kHz 60.024kHz 47.396kHz 60.
CONNECTOR PIN ASSIGNMENT DVI-D 24pin Connector *1 1 8 16 24 9 17 DVI-D Pin Input Signal Pin Input Signal 1 Red video 9 2 Green video 10 Ground 3 Blue video 11 +5V NC 4 NC 12 Data line (SDA)* 5 Ground 13 H-Sync 6 Red video ground 14 V-Sync 7 Green video ground 15 Clock line (SCL)* 8 Blue video ground * Compliant to VESA DDC. Pin Input Signal Input Signal Pin 1 T.M.D.S Data 2– 13 2 T.M.D.S Data 2+ 14 +5V 3 T.M.D.