USER MANUAL ENGLISH DEUTSCH FRANCAIS NEDERLANDS Thank you very much for choosing the iiyama LCD monitor. We recommend that you take a few minutes to read this comprehensive manual carefully before installing and switching on the monitor. Please keep this manual in a safe place for your future reference.
ENGLISH
CE MARKING DECLARATION OF CONFORMITY This LCD monitor complies with the requirements of the EC Directive 2004/108/EC “EMC Directive” , 2006/95/EC “Low Voltage Directive” and 2009/125/EC “ErP Directive”. The electro-magnetic susceptibility has been chosen at a level that gives correct operation in residential areas, business and light industrial premises and small-scale enterprises, inside as well as outside of the buildings.
TABLE OF CONTENTS FOR YOUR SAFETY.............................................................................................. 1 SAFETY PRECAUTIONS ................................................................................ 1 SPECIAL NOTES ON LCD MONITORS.......................................................... 3 ENGLISH CUSTOMER SERVICE .................................................................................... 3 CLEANING....................................................................
ENGLISH
FOR YOUR SAFETY SAFETY PRECAUTIONS WARNING STOP OPERATING THE MONITOR WHEN YOU SENSE TROUBLE If you notice any abnormal phenomena such as smoke, strange sounds or fumes, unplug the monitor ENGLISH and contact your dealer or iiyama service center immediately. Further use may be dangerous and can cause fire or electric shock. NEVER REMOVE THE CABINET High voltage circuits are inside the monitor. Removing the cabinet may expose you to the danger of fire or electric shock.
CAUTION INSTALLATION LOCATION Do not install the monitor where sudden temperature changes may occur, or in humid, dusty or smoky areas as it may cause fire, electric shock or damage. You should also avoid areas where the sun shines directly on the monitor. DO NOT PLACE THE MONITOR IN A HAZARDOUS POSITION MAINTAIN GOOD VENTILATION Ventilation slots are provided to keep the monitor from overheating. Covering the slots may cause fire.
SPECIAL NOTES ON LCD MONITORS The following symptoms are normal with LCD monitors and do not indicate a problem. NOTE When you first turn on the LCD monitor, the picture may not fit in the display area because of the type of computer that is used. In this case, adjust the picture position to the correct position. Due to the nature of the backlight, the screen may flicker during initial use. Turn off the Power Switch and then turn it on again to make sure the flicker disappears.
BEFORE YOU OPERATE THE MONITOR FEATURES Supports Resolutions up to 1280 × 1024 2 High Contrast 1000:1 (Typical) / Brightness 250cd/m (Typical), Quick Response Time 5ms (Black, White, Black) : ProLite P1705S / ProLite PB1705S 2 High Contrast 1000:1 (Typical) / Brightness 250cd/m (Typical), Quick Response Time 5ms (Black, White, Black) : ProLite P1905S ENGLISH Digital Character Smoothing Automatic Set-up Stereo Speakers 2 × 1W Stereo Speakers Plug & Play VESA DDC2B Compliant Windows® 95/98/200
FITTING AND REMOVAL OF BASE : ProLite P1705S / ProLite P1905S CAUTION Put the monitor on a stable surface. The monitor may cause injury or damage if it falls or is dropped. Do not give a strong impact to the monitor. It may cause damage. ENGLISH Unplug the monitor before removal or installation to avoid electric shock or damage. Put a piece of soft cloth on the table beforehand to prevent the monitor from being scratched. Lay the monitor flat on a table with front face down.
FITTING AND REMOVAL OF BASE : ProLite PB1705S CAUTION Put the monitor on a stable surface. The monitor may cause injury or damage if it falls or is dropped. Do not give a strong impact to the monitor. It may cause damage. Put a piece of soft cloth on the table beforehand to prevent the monitor from being scratched. Lay the monitor flat on a table with front face down. Install the Stand-Base to the Monitor.
CONTROLS AND CONNECTORS ENGLISH Power Switch ( ) / Power Indicator Blue: Normal operation NOTE Orange: Power Management The monitor enters into power management mode which reduces the power consumption to less than 1W when receiving no horizontal and/or vertical sync signal.
CONNECTING YOUR MONITOR Ensure that both the computer and the monitor are switched off. Connect the computer to the monitor with the signal cable. Connect the monitor to the audio equipment with the Audio Cable for computer when using the audio features. Connect the Power Cable to the monitor first and then to the power supply. Power of the monitor and the computer is turned on. computer used. An incorrect connection may cause serious damage to both the monitor and the computer.
COMPUTER SETTING Signal Timing Change to the desired signal timing listed on page 26: COMPLIANT TIMING. Windows 95/98/2000/Me/XP/Vista/7 Plug & Play The iiyama LCD monitor complies with DDC2B of VESA standard. The Plug & Play function runs on Windows 95/98/2000/Me/XP/Vista/7 by connecting the monitor to DDC2B compliant computer with the Signal Cable supplied.
ADJUSTING THE HEIGHT AND THE VIEWING ANGLE : ProLite PB1705S For optimal viewing it is recommended to position yourself directly opposite the full face of the monitor, then adjust the monitor’s height and angle to your own preference. 1q 20q -TOP- Hold the panel so that the monitor does not topple when you change the monitor’s height or angle. 612 612 612 80mm You are able to adjust the monitor's height up to 80mm, 20 ENGLISH degrees upward, 1 degrees downward.
OPERATING THE MONITOR To create the best picture, your iiyama LCD monitor has been preset at the factory with the COMPLIANT TIMING shown on page 26. You are also able to adjust the picture by following the button operation shown below. For more detailed adjustments, see page 16 for SCREEN ADJUSTMENTS. Press the 1 Button to start the On Screen Display feature. There are additional Menu items which can be switched by using the / Buttons.
ADJUSTMENT MENU CONTENTS Auto Image Adjust Auto Image Adjust Adjustment Item Auto Image Adjust * Problem / Option Direct Button to Press Adjust H. / V. Position, Horizontal Size and Fine Tune automatically. NOTE * The screen becomes dark for approximately five seconds during the adjustment. For best results, use the Auto Image Adjust in conjunction with the adjustment pattern. See page 16 for SCREEN ADJUSTMENTS.
Input Select Input Select Adjustment Item Problem / Option Input Select Analog Select the D-sub input. Digital Select the DVI input. When only one of the two signal inputs is connected to the signal source, the one connected is automatically selected. Input Select function is not available if there is no signal input from the selected connector or during the power management mode.
Information Information Information Displays information regarding the current input signal coming from the graphic card in your computer. Analog H.Frequency: 63.9KHz V.Frequency: 60.0Hz Resolution: 1280 x 1024 Pixel Clock: 107.8MHz Serial Number: 1108901000001 Model Number: PLP1705S NOTE See your graphic card user guide for more information about changing the resolution and refresh.
Memory Recall Memory Recall Adjustment Item ENGLISH Memory Recall Problem / Option Button to Press Factory-preset data is restored. Direct You can display an adjustment scale directly by using the following button operations. KEY LOCK (OSD and POWER SWITCH) : Lock : Press the 1 Button and Button and hold down for 10 seconds. Unlock : Press the 1 Button and ECO : 15 Button and hold down for 10 seconds. On : Press the 1 Button and Button at the same time when the Menu is not displayed.
SCREEN ADJUSTMENTS Adjust the image by following the procedure below to get the desired picture when selecting Analog input. The screen adjustments described in this manual are designed to set image position and minimize flicker or blur for the particular computer in use. Displayed text or lines will be blurred or irregular in thickness when the picture is stretched due to the screen enlargement process.
Press the 2 Button. (Auto Image Adjust) Adjust the image manually by following procedure below when the screen has a flicker or blur, or the picture does not fit in the display area after performing the Auto Image Adjust. Adjust the V.Position so that the top and bottom of the picture frame will fit to the display ENGLISH area. 1) Adjust the H.Position so that the left side of the picture frame will move to the left edge of the display area.
NOTE In case the strong flicker or blurs remain on a part of the screen, repeat steps and NOTE because the Horizontal Size may not be adjusted correctly. If the flicker or blurs still remain, set the refresh rate of computer to low (60Hz) and repeat steps from again. Adjust the H.Position after the Fine Tune adjustment if the horizontal position moves during the adjustment.
POWER MANAGEMENT FEATURE The power management feature of this product complies with power saving requirement of ENERGY STAR® and VESA DPMS. When activated, it automatically reduces unnecessary power consumption of the monitor when your computer is not in use. To use the feature, the monitor needs to be connected to a VESA DPMS compliant computer. There is a power management step the monitor takes as described below.
TROUBLE SHOOTING If the monitor fails to operate correctly, please follow the steps below for a possible solution. 1. Perform the adjustments described in OPERATING THE MONITOR, depending on the problem you have. If the monitor does not get a picture, skip to 2. 2. Consult the following items if you cannot find an appropriate adjustment item in OPERATING THE MONITOR or if the problem persists. Problem ENGLISH 3.
ENGLISH Problem Check No sound. The audio equipment (computer etc.) is ON. The Audio Cable is properly connected. The Volume is turned up. The Mute is OFF. The audio output level of the audio equipment is within the specification of the monitor. The sound is too loud or too quiet. The audio output level of the audio equipment is within the specification of the monitor. A strange noise is heard. The Audio Cable is properly connected.
APPENDIX Design and specifications are subject to change without prior notice. SPECIFICATIONS : ProLite P1705S 17" Driving system a-Si TFT Active Matrix Size Diagonal: 17" Pixel pitch 0.264mm H × 0.264mm V Brightness 250cd/m2 (Typical) Contrast ratio 1000 : 1 (Typical) Viewable angle Right / Left : 85 degrees each, Up / Down : 80 degrees each (Typical) Response time ENGLISH Size Category LCD Panel 5ms (Black, White, Black) Display Colors Approx.16.7M Sync Frequency Horizontal: 31.0-81.
ENGLISH SPECIFICATIONS : ProLite PB1705S Size Category 17" LCD Panel Driving system a-Si TFT Active Matrix Size Diagonal: 17" Pixel pitch 0.264mm H × 0.264mm V Brightness 250cd/m2 (Typical) Contrast ratio 1000 : 1 (Typical) Viewable angle Right / Left : 85 degrees each, Up / Down : 80 degrees each (Typical) Response time 5ms (Black, White, Black) Display Colors Approx.16.7M Sync Frequency Horizontal: 31.0-81.0kHz, Vertical: 56-75Hz Maximum Resolution 1280 × 1024, 1.
SPECIFICATIONS : ProLite P1905S Size Category 19" LCD Panel Driving system a-Si TFT Active Matrix Size Diagonal: 19" Pixel pitch 0.294mm H × 0.294mm V Brightness 250cd/m2 (Typical) 1000 : 1 (Typical) Viewable angle Right / Left : 85 degrees each, Up : 85 degrees, Down : 75 degrees (Typical) Response time ENGLISH Contrast ratio 5ms (Black, White, Black) Display Colors Approx.16.7M Sync Frequency Horizontal: 31.0-81.0kHz, Vertical: 56-75Hz Maximum Resolution 1280 × 1024, 1.
DIMENSIONS : ProLite P1705S 369.0mm/14.5" 339.5mm/13.4" ENGLISH 200.5mm/7.89" 401.5mm/15.8" 272.0mm/10.7" 328.5mm/12.9" 59.5mm/2.34" 201.5mm/7.93" DIMENSIONS : ProLite PB1705S 369.0mm/14.5" 339.5mm/13.4" 175.0mm/6.89" -TOP- 403.0mm/15.9" (483.0mm/19.0") 272.0mm/10.7" 328.5mm/12.9" 59.5mm/2.34" 210.0mm/8.27" ( ): Maximum adjustment range DIMENSIONS : ProLite P1905S 414.5mm/16.3" 378.0mm/14.9" 200.5mm/7.89" 420.5mm/16.6" 303.0mm/11.9" 362.5mm/14.3" 70.5mm/2.78" 201.5mm/7.
Video Mode VGA SVGA 640 × 480 800 × 600 VESA XGA SXGA VGA TEXT Macintosh 1024 × 768 1280 × 1024 PC Input Horizontal Frequency Vertical Frequency Dot Clock 31.469kHz 59.940Hz 25.175MHz 37.500kHz 75.000Hz 31.500MHz 37.861kHz 72.809Hz 31.500MHz 35.156kHz 56.250Hz 36.000MHz 37.879kHz 60.316Hz 40.000MHz 48.077kHz 72.188Hz 50.000MHz 46.875kHz 75.000Hz 49.500MHz 48.363kHz 60.004Hz 65.000MHz 56.476kHz 70.069Hz 75.000MHz 60.023kHz 75.029Hz 78.750MHz 63.981kHz 60.
