USER MANUAL ENGLISH Thank you very much for choosing the iiyama LCD monitor. We recommend that you take a few minutes to read this comprehensive manual carefully before installing and switching on the monitor. Please keep this manual in a safe place for your future reference.
ENGLISH
CE MARKING DECLARATION OF CONFORMITY This LCD monitor complies with the requirements of the EC/EU Directive 2014/30/EU “EMC Directive”, 2014/35/EU “Low Voltage Directive”, 2009/125/EC “ErP Directive” and 2011/65/EU “RoHS Directive”. The electro-magnetic susceptibility has been chosen at a level that gives correct operation in residential areas, business and light industrial premises and small-scale enterprises, inside as well as outside of the buildings.
TABLE OF CONTENTS FOR YOUR SAFETY............................................................................1 SAFETY PRECAUTIONS................................................................1 ENGLISH SPECIAL NOTES ON LCD MONITORS .........................................3 CUSTOMER SERVICE ...................................................................3 CLEANING ......................................................................................3 BEFORE YOU OPERATE THE MONITOR ....................
FOR YOUR SAFETY SAFETY PRECAUTIONS WARNING If you notice any abnormal phenomena such as smoke, strange sounds or fumes, unplug the monitor and contact your dealer or iiyama service center immediately. Further use may be dangerous and can cause fire or electric shock. NEVER REMOVE THE CABINET High voltage circuits are inside the monitor. Removing the cabinet may expose you to the danger of fire or electric shock.
CAUTION INSTALLATION LOCATION Do not install the monitor where sudden temperature changes may occur, or in humid, dusty or smoky areas as it may cause fire, electric shock or damage. You should also avoid areas where the sun shines directly on the monitor. ENGLISH DO NOT PLACE THE MONITOR IN A HAZARDOUS POSITION The monitor may topple and cause injury if not suitably located.
SPECIAL NOTES ON LCD MONITORS NOTE When you first turn on the LCD monitor, the picture may not fit in the display area because of the type of computer that is used. In this case, adjust the picture position to the correct position. You may find slightly uneven brightness on the screen depending on the desktop pattern you use. Due to the nature of the LCD screen, an afterimage of the previous screen may remain after switching the image, when the same image is displayed for hours.
BEFORE YOU OPERATE THE MONITOR FEATURES Supports Resolutions up to 1024 × 768 2 High Contrast 800:1 (Typical) / Brightness 370cd/m (Typical : without Touch panel) ENGLISH Blue Light Reducer Digital Character Smoothing Automatic Set-up Stereo Speakers 2 × 2W Stereo Speakers Plug & Play VESA DDC2B Compliant Windows® XP/Vista/7/8/8.
SPECIAL NOTES ON TOUCH PANEL Permanent damage can occur if Sharp Edged, Pointed or Metal items are used to activate Touch. This could invalidate any remaining warranty. We recommend to use a plastic stylus (tip R0.8 or over) or finger. WALL MOUNTING Mounting Stage Screw ENGLISH WARNING W h e n y o u u s e w i t h t h e w a l l m o u n t i n g , i n consideration of thickness of the mounting stage, tighten the M4 Screw with washer which “L” length is 8mm to fasten the monitor.
FITTING AND REMOVAL OF BASE CAUTION Put the monitor on a stable surface. The monitor may cause injury or damage if it falls or is dropped. Do not give a strong impact to the monitor. It may cause damage. Unplug the monitor before removal or installation to avoid electric shock or damage. ENGLISH Put a piece of soft cloth on the table beforehand to prevent the monitor from being scratched. Lay the monitor flat on a table with front face down.
ENGLISH CONTROLS AND CONNECTORS Menu Button ( ) Up / Left / Auto Adjustment Button ( Down / Right Button ( ) Return / Exit Button ( ) Power Switch ( ) ) USB Connector VGA(D-sub) mini 15pin Connector Connector for AC Adapter ( : Direct current) Audio Connector Speakers BEFORE YOU OPERATE THE MONITOR 7
CONNECTING YOUR MONITOR ENGLISH Ensure that both the computer and the monitor are switched off. Connect the computer to the monitor with the signal cable. Connect the computer to the monitor with the USB Cable. Connect the monitor to the audio equipment with the Audio Cable for computer when using the audio features. Connect the AC Adapter to the monitor and the Power Cable to the AC Adapter first and then connect to the power supply. Turn on your monitor and computer.
COMPUTER SETTING Signal Timing Change to the desired signal timing listed on page 24: COMPLIANT TIMING. http://www.iiyama.com NOTE For additional information on how to download the driver for your touch screen monitor, please access the internet site noted above. Procedure for turning ON the Power Switch Turn ON the monitor first, and then the computer. Touch screen driver software Touch screen driver software and system may not start when you start your computer while touching he screen.
ADJUSTING THE VIEWING ANGLE ENGLISH For optimal viewing it is recommended to look at the full face of the monitor. Hold the panel so that the monitor does not topple when you change the monitor’s angle. You are able to adjust the monitor’s angle up to 70 degrees upward, 10 degrees downward. NOTE Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen. Careful attention is required not to catch your fingers or hands when you change the angle.
OPERATING THE MONITOR To create the best picture, your iiyama LCD monitor has been preset at the factory with the COMPLIANT TIMING shown on page 24. You are also able to adjust the picture by following the button operation shown below. For more detailed adjustments, see page 17 for SCREEN ADJUSTMENTS. Press the Button to start the On Screen Display feature. There are additional Menu items which can be switched by using the / Buttons.
Direct LOCK MODE: Pressing and holding of the Button for 3-4 seconds when the Menu is not displayed. * The OSD menu is not displayed when the OSD is locked. Pressing and holding of the for 3 - 4 seconds again when the Menu is not displayed. The following OSD menu is displayed. ENGLISH Adjustment Item POWER-key Lock OSD-key Lock 12 OPERATING THE MONITOR Problem / Option LOCK The POWER SWITCH is Locked. UNLOCK The POWER SWITCH is Unlocked. LOCK The OSD menu is Locked.
ADJUSTMENT MENU CONTENTS PICTURE PICTURE Backlight Brightness Contrast Adjustment Item Problem / Option Backlight Too dark Too bright Brightness * Too dark Too bright Contrast Too dull Too intense Button to Press 01234 Sharpness You can change the picture quality from 0 to 4 (soft to sharp). Press the Button to change the picture quality in numerical order. Press the Button to change the picture quality in reverse numerical order.
DISPLAY DISPLAY Auto Adjustment H Position V Position Pixel Clock Phase ENGLISH Adjustment Item Auto Adjustment *1 Direct Problem / Option Adjust H/V Position, Pixel Clock and Phase automatically. H Position Too left Too right V Position Too low Too high Pixel Clock *2 Too narrow Too wide Phase *2 Button to Press To correct flickering text or lines *1 For best results, use the Auto Adjust in conjunction with the adjustment pattern. See page 17 for SCREEN ADJUSTMENTS.
COLOR COLOR Color Temp User Preset Standard Picture Mode Color Temp Problem / Option 9300 7500 6500 5500 User Preset Picture Mode Standard Button to Press Bluish white Greenish white Yellowish white Reddish white Red Too weak Green Too strong Blue ENGLISH Adjustment Item Typical Low Blue Light Blue light is reduced. AUDIO AUDIO Volume Mute Adjustment Item Volume Mute Off Problem / Option Button to Press Too soft Too loud On Turn off the sound temporarily.
OTHER OTHER Reset OSD Time OSD H Position OSD V Position English Language ENGLISH Adjustment Item Problem / Option Button to Press Reset Factory-preset data is restored. OSD Time You can set the OSD display duration time between 5 and 60 seconds.
SCREEN ADJUSTMENTS The screen adjustments described in this manual are designed to set image position and minimize flicker or blur for the particular computer in use. The monitor is designed to provide the best performance at resolution of 1024 × 768, but can not provide the best at resolutions of less than 1024 × 768 because the picture is automatically stretched to fit the full screen. It is recommended to operate at resolution of 1024 × 768 in normal use.
Press the Button. (Auto Adjustmnet) Adjust the image manually by following procedure below when the screen has a flicker or blur, or the picture does not fit in the display area after performing the Auto Adjust. ENGLISH Adjust the V Position so that the top and bottom of the picture frame will fit to the display area. 1) Adjust the H Position so that the left side of the picture frame will move to the left edge of the display area.
NOTE In case the strong flicker or blurs remain on a part of the screen, repeat steps and because the Pixel Clock may not be adjusted correctly. If the flicker or blurs still remain, set the refresh rate of computer to low (60Hz) and repeat steps from again. Adjust the H Position after the Phase adjustment if the horizontal position moves during the adjustment. Adjust the Brightness and Color to get the desired picture after you complete the Pixel Clockand Phase adjustments.
POWER MANAGEMENT FEATURE ENGLISH The power management feature of this product complies with power saving requirement of VESA DPMS. When activated, it automatically reduces unnecessary power consumption of the monitor when your computer is not in use. To use the feature, the monitor needs to be connected to a VESA DPMS compliant computer. There is a power management step the monitor takes as described below. The power management function, including any timer settings is configured by the operating system.
TROUBLE SHOOTING If the monitor fails to operate correctly, please follow the steps below for a possible solution. 1. Perform the adjustments described in OPERATING THE MONITOR, depending on the problem you have. If the monitor does not get a picture, skip to 2. 2. Consult the following items if you cannot find an appropriate adjustment item in OPERATING THE MONITOR or if the problem persists. 3.
RECYCLING INFORMATION ENGLISH For better environment protection please don't dispose your monitor. Please visit our web site: www.iiyama.com/recycle for monitor recycling.
APPENDIX Design and specifications are subject to change without prior notice. SPECIFICATIONS Technology Projected capacitive 10pt touch Light transmission 88% Hardness 7H Total thickness Communication system 1.2mm ENGLISH Touch Screen USB serial transfer Size Category 15" LCD Panel Diagonal: 15" (38cm) Panel technology TN Size Pixel pitch 0.297mm H × 0.
DIMENSIONS 340.5mm/13.4” 304.0mm/12.0” 198.0mm/7.8” ENGLISH 308.0mm/12.1” 228.0mm/9.0” 268.0mm/10.6” 44.5mm/1.7” 266.5mm/10.5” COMPLIANT TIMING Horizontal Frequency Video Mode VGA VESA SVGA XGA 640 × 480 800 × 600 1024 × 768 Dot Clock 31.469kHz Vertical Frequency 59.940Hz 25.175MHz 37.500kHz 75.000Hz 31.500MHz 37.861kHz 72.809Hz 31.500MHz 35.156kHz 56.250Hz 36.000MHz 37.879kHz 60.317Hz 40.000MHz 46.875kHz 75.000Hz 49.500MHz 48.077kHz 72.188Hz 50.000MHz 48.363kHz 60.
