USER MANUAL ENGLISH Thank you very much for choosing the iiyama LCD monitor. We recommend that you take a few minutes to read this comprehensive manual carefully before installing and switching on the monitor. Please keep this manual in a safe place for your future reference.
ENGLISH
CE MARKING DECLARATION OF CONFORMITY This LCD monitor complies with the requirements of the EC/EU Directive 2004/108/EC “EMC Directive”, 2006/95/EC “Low Voltage Directive”, 2009/125/EC “ErP Directive” and 2011/65/EU “RoHS Directive”. The electro-magnetic susceptibility has been chosen at a level that gives correct operation in residential areas, business and light industrial premises and small-scale enterprises, inside as well as outside of the buildings.
ENGLISH TABLE OF CONTENTS FOR YOUR SAFETY..........................................................................1 SAFETY PRECAUTIONS..............................................................1 SPECIAL NOTES ON LCD MONITORS .......................................3 CUSTOMER SERVICE .................................................................3 CLEANING ....................................................................................3 BEFORE YOU OPERATE THE MONITOR ...............................
FOR YOUR SAFETY SAFETY PRECAUTIONS WARNING If you notice any abnormal phenomena such as smoke, strange sounds or fumes, unplug the monitor and contact your dealer or iiyama service center immediately. Further use may be dangerous and can cause fire or electric shock. NEVER REMOVE THE CABINET High voltage circuits are inside the monitor. Removing the cabinet may expose you to the danger of fire or electric shock.
CAUTION INSTALLATION LOCATION Do not install the monitor where sudden temperature changes may occur, or in humid, dusty or smoky areas as it may cause fire, electric shock or damage. You should also avoid areas where the sun shines directly on the monitor. ENGLISH DO NOT PLACE THE MONITOR IN A HAZARDOUS POSITION The monitor may topple and cause injury if not suitably located.
SPECIAL NOTES ON LCD MONITORS NOTE When you first turn on the LCD monitor, the picture may not fit in the display area because of the type of computer that is used. In this case, adjust the picture position to the correct position. Due to the nature of the backlight, the screen may flicker during initial use. Turn off the Power Switch and then turn it on again to make sure the flicker disappears. You may find slightly uneven brightness on the screen depending on the desktop pattern you use.
BEFORE YOU OPERATE THE MONITOR FEATURES Supports Resolutions up to 1024 × 768 : ProLite T1531SR / ProLit T1531SAW / ProLite T1532SR ENGLISH Supports Resolutions up to 1280 × 1024 : ProLite T1731SR / ProLite T1731SAW / ProLite T1931SR / ProLite T1931SAW 2 High Contrast 500:1 (Typical: with Touch panel) / Brightness 200cd/m (Typical: with Touch panel) : ProLite T1531SR / ProLite T1532SR 2 High Contrast 500:1 (Typical: with Touch panel) / Brightness 230cd/m (Typical: with Touch panel) : ProLit T1531S
CHECKING THE CONTENTS OF THE PACKAGE The following accessories are included in your package. Check to see if they are enclosed with the monitor. If anything is missing or damaged, please contact your local iiyama dealer or regional iiyama office. CAUTION D-Sub Signal Cable DVI-D Cable USB Cable Audio Cable Touch Panel Driver Disk (CD-ROM)*2 Quick Start Guide *1 The rating of the Power Cable enclosed in 120V area is 10A/125V.
ENGLISH CONTROLS AND CONNECTORS Menu Button ( ) Scroll Up / Brightness Button ( Scroll Down / Mute Button ( Select / Auto Button ( Power Switch ( ) ) ) ) Keyhole for Security Lock NOTE You can fasten a security lock and cable to prevent the monitor from being removed without your permission.
CONNECTING YOUR MONITOR NOTE The signal cables used for connecting the computer and monitor may vary with the type of computer used. An incorrect connection may cause serious damage to both the monitor and the computer. The cable supplied with the monitor is for a standard 15 pin D-Sub connector. If a special cable is required please contact your local iiyama dealer or regional iiyama office.
ENGLISH COMPUTER SETTING Signal Timing Change to the desired signal timing listed on page 28: COMPLIANT TIMING. Windows 95/98/2000/Me/XP/Vista/7 Plug & Play The iiyama LCD monitor complies with DDC2B of VESA standard. The Plug & Play function runs on Windows 95/98/2000/Me/XP/Vista/7 by connecting the monitor to DDC2B compliant computer with the Signal Cable supplied.
OPERATING THE MONITOR To create the best picture, your iiyama LCD monitor has been preset at the factory with the COMPLIANT TIMING shown on page 28. You are also able to adjust the picture by following the button operation shown below. For more detailed adjustments, see page 14 for SCREEN ADJUSTMENTS. Press the Button to start the On Screen Display feature. There are additional Menu items which can be switched by using the / Buttons. ENGLISH CO NTRAS T BRIG HTNE S S 1280x1024 FH: 63KHz F V: 5 9 .
ADJUSTMENT MENU CONTENTS CO NTRAS T BRIG HTNE S S ENGLISH 1280x1024 FH: 63KHz F V: 5 9 . 9 H z Adjustment Item Button to Press Too dull Too intense CONTRAST BRIGHTNESS * Problem / Option Direct Too dark Too bright * Adjust the Brightness when you are using the monitor in a dark room and feel the screen is too bright. Direct You can skip the Menu items and display an adjustment scale directly by using the following button operations.
AUTO ADJUST H-POSITION V-POSITION H-SIZE FINE Adjustment Item AUTO ADJUST *1 Direct Problem / Option Adjust H/V-POSITION, H-SIZE and FINE automatically. H-POSITION Too left Too right V-POSITION Too low Too high H-SIZE *2 Too narrow Too wide FINE *2 Button to Press To correct flickering text or lines *1 For best results, use the Auto Adjust in conjunction with the adjustment pattern. See page 14 for SCREEN ADJUSTMENTS. *2 See page 14 for SCREEN ADJUSTMENTS.
OS D H - P OS I TI ON OS D V- P OS I TI ON OS D TI ME OU T RESET I N P U T S E LE C T ENGLISH Adjustment Item Problem / Option Button to Press OSD H-POSITION OSD is too left OSD is too right OSD V-POSITION OSD is too low OSD is too high OSD TIMEOUT You can set the OSD display duration time between 5 and 60 seconds. RESET Factory-preset data is restored. INPUT SELECT VGA Select the analog input. DVI Select the digital input.
Adjustment Item COLOR TEMP. RED GREEN BLUE 94 90 100 Problem / Option Button to Press 9300 6500 5500 Bluish white Reddish white Greenish white 7500 Yellowish white RED Too weak GREEN Too strong BLUE User ENGLISH 9300 6500 5500 7500 USER VOLUME MUTE Adjustment Item Button to Press Too soft Too loud VOLUME MUTE Problem / Option ON Turn off the sound temporarily. OFF Return the sound volume to the previous level.
SCREEN ADJUSTMENTS ENGLISH Adjust the image by following the procedure below to get the desired picture when selecting Analog input. The screen adjustments described in this manual are designed to set image position and minimize flicker or blur for the particular computer in use.
C Press the AUTO Button. (AUTO ADJUST) D Adjust the image manually by following procedure below when the screen has a flicker or blur, or the picture does not fit in the display area after performing the Auto Adjust. ENGLISH E Adjust the V-POSITION so that the top and bottom of the picture frame will fit to the display area. F 1) Adjust the H-POSITION so that the left side of the picture frame will move to the left edge of the display area.
ENGLISH G Adjust the FINE to correct horizontal wavy noise, flicker or blur in the zebra pattern. NOTE In case the strong flicker or blurs remain on a part of the screen, repeat steps F and G because the H-SIZE may not be adjusted correctly. If the flicker or blurs still remain, set the refresh rate of computer to low (60Hz) and repeat steps from C again. Adjust the H-POSITION after the FINE adjustment if the horizontal position moves during the adjustment.
POWER MANAGEMENT FEATURE Power Management Mode When the H-sync signal / V-sync signal / H and V sync signals from the computer are off, the monitor enters into Power Management Mode which reduces the power consumption to less than 2W or 3W.* The screen becomes dark. From Power Management Mode, the image reappears in several seconds when either the keyboard or the mouse are touched again.
TROUBLE SHOOTING If the monitor fails to operate correctly, please follow the steps below for a possible solution. ENGLISH 1. Perform the adjustments described in OPERATING THE MONITOR, depending on the problem you have. If the monitor does not get a picture, skip to 2. 2. Consult the following items if you cannot find an appropriate adjustment item in OPERATING THE MONITOR or if the problem persists. 3.
RECYCLING INFORMATION ENGLISH For better environment protection please don't dispose your monitor. Please visit our web site: www.iiyama.com/recycle for monitor recycling.
APPENDIX SPECIFICATIONS : ProLite T1531SR ENGLISH Touch Screen Technology Resistive-Film Surface processing Anti-glare treatment Light transmission 80% Communication USB serial transfer or RS-232C serial transfer system Size Category LCD Panel Driving system Size 15" a-Si TFT Active Matrix Diagonal: 15" (38cm) Pixel pitch 0.297mm H × 0.
SPECIFICATIONS : ProLite T1531SAW Technology Surface acoustic wave Surface processing Anti-glare treatment Light transmission 92% Communication USB serial transfer or RS-232C serial transfer system Size Category 15" LCD Panel Driving system a-Si TFT Active Matrix Size Diagonal: 15" (38cm) Pixel pitch 0.297mm H × 0.
SPECIFICATIONS : ProLite T1532SR Touch Screen Technology Resistive-Film Surface processing Anti-glare treatment Light transmission 80% Communication USB serial transfer or RS-232C serial transfer system 15" LCD Panel Driving system a-Si TFT Active Matrix ENGLISH Size Category Size Diagonal: 15" (38cm) Pixel pitch 0.297mm H × 0.
SPECIFICATIONS : ProLite T1731SR Technology Resistive-Film Surface processing Anti-glare treatment Light transmission 80% Communication USB serial transfer or RS-232C serial transfer system Size Category LCD Panel Driving system Size 17" a-Si TFT Active Matrix Diagonal: 17" (43cm) ENGLISH Touch Screen Pixel pitch 0.264mm H × 0.
SPECIFICATIONS : ProLite T1731SAW Touch Screen Technology Surface acoustic wave Surface processing Anti-glare treatment Light transmission 92% Communication USB serial transfer or RS-232C serial transfer system 17" LCD Panel Driving system a-Si TFT Active Matrix ENGLISH Size Category Size Diagonal: 17" (43cm) Pixel pitch 0.264mm H × 0.
SPECIFICATIONS : ProLite T1931SR Technology Resistive-Film Surface processing Anti-glare treatment Light transmission 80% Communication USB serial transfer or RS-232C serial transfer system Size Category LCD Panel Driving system 19" a-Si TFT Active Matrix Size Diagonal: 19" (48cm) Pixel pitch 0.294mm H × 0.
SPECIFICATIONS : ProLite T1931SAW Touch Screen Surface acoustic wave Surface processing Anti-glare treatment Light transmission 92% Technology Communication system USB serial transfer or RS-232C serial transfer Size Category 19" LCD Panel Driving system a-Si TFT Active Matrix ENGLISH Size Diagonal: 19" (48cm) Pixel pitch 0.294mm H × 0.
DIMENSIONS : ProLite T1531SR / ProLite T1531SAW / ProLite T1532SR 351.0mm/13.8" 306.0mm/12.0" ENGLISH 201.0mm/7.9" 306.0mm/12.0" 230.0mm/9.1" 275.0mm/10.8" 59.0mm/2.3" 222.5mm/8.8" DIMENSIONS : ProLite T1731SR / ProLite T1731SAW 387.0mm/15.2" 340.0mm/13.4" 201.0mm/7.9" 342.0mm/13.5" 272.0mm/10.7" 320.0mm/12.6" 59.0mm/2.3" 222.5mm/8.8" DIMENSIONS : ProLite T1931SR / ProLite T1931SAW 432.0mm/17.0" 378.0mm/14.9" 218.0mm/8.6" 390.0mm/15.4" 303.0mm/11.9" 358.0mm/14.1" 59.0mm/2.3" 249.5mm/9.
COMPLIANT TIMING Video Mode VGA ENGLISH SVGA 640 × 480 800 × 600 VESA XGA SXGA 1024 × 768 1280 × 1024 Dot Clock Horizontal Frequency 31.469kHz Vertical Frequency 59.940Hz 25.175MHz 37.500kHz 75.000Hz 31.500MHz 37.861kHz 72.809Hz 31.500MHz 35.156kHz 56.250Hz 36.000MHz 37.879kHz 60.317Hz 40.000MHz 46.875kHz 75.000Hz 49.500MHz 48.077kHz 72.188Hz 50.000MHz 48.363kHz 60.004Hz 65.000MHz 56.476kHz 70.069Hz 75.000MHz 60.023kHz 75.029Hz 78.750MHz 63.981kHz 60.020Hz 108.
