USER MANUAL ENGLISH Thank you very much for choosing the iiyama LCD monitor. We recommend that you take a few minutes to read this comprehensive manual carefully before installing and switching on the monitor. Please keep this manual in a safe place for your future reference.
ENGLISH
CE MARKING DECLARATION OF CONFORMITY This LCD monitor complies with the requirements of the EC/EU Directive 2004/108/EC “EMC Directive”, 2006/95/EC “Low Voltage Directive”, 2009/125/EC “ErP Directive” and 2011/65/EU “RoHS Directive”. The electro-magnetic susceptibility has been chosen at a level that gives correct operation in residential areas, business and light industrial premises and small-scale enterprises, inside as well as outside of the buildings.
TABLE OF CONTENTS FOR YOUR SAFETY............................................................................1 SAFETY PRECAUTIONS................................................................1 SPECIAL NOTES ON LCD MONITORS .........................................3 ENGLISH CUSTOMER SERVICE ...................................................................3 CLEANING ......................................................................................3 BEFORE YOU OPERATE THE MONITOR ....................
FOR YOUR SAFETY SAFETY PRECAUTIONS WARNING If you notice any abnormal phenomena such as smoke, strange sounds or fumes, unplug the monitor and contact your dealer or iiyama service center immediately. Further use may be dangerous and can cause fire or electric shock. NEVER REMOVE THE CABINET High voltage circuits are inside the monitor. Removing the cabinet may expose you to the danger of fire or electric shock.
CAUTION INSTALLATION LOCATION Do not install the monitor where sudden temperature changes may occur, or in humid, dusty or smoky areas as it may cause fire, electric shock or damage. You should also avoid areas where the sun shines directly on the monitor. ENGLISH DO NOT PLACE THE MONITOR IN A HAZARDOUS POSITION The monitor may topple and cause injury if not suitably located.
SPECIAL NOTES ON LCD MONITORS NOTE When you first turn on the LCD monitor, the picture may not fit in the display area because of the type of computer that is used. In this case, adjust the picture position to the correct position. Due to the nature of the backlight, the screen may flicker during initial use. Turn off the Power Switch and then turn it on again to make sure the flicker disappears. You may find slightly uneven brightness on the screen depending on the desktop pattern you use.
BEFORE YOU OPERATE THE MONITOR FEATURES Supports Resolutions up to 1920 × 1080 2 High Contrast 1000:1 (Typical: with Touch panel) / Brightness 225cd/m (Typical: with Touch panel) ENGLISH Digital Character Smoothing Automatic Set-up Plug & Play VESA DDC2B Compliant Windows® 95/98/2000/Me/XP/Vista/7 Compliant Power Management (VESA DPMS Compliant) VESA Mounting Standard (100mm×100mm) Compliant IP54 Standard Compliant (Only front face) Windows8 touch environment Basic touch operations can
WALL MOUNTING WARNING When you use with the wall mounting, in consideration of thickness of the mounting stage, tighten the M4 Screw with washer which “L” length is 8mm to fasten the monitor. Using the screw longer than this may cause electric shock or damage because it may contact with the electrical parts inside the monitor.
CONTROLS AND CONNECTORS ENGLISH Remote Control OSD Key* Menu Button (MENU)* Scroll Up / Brightness Button ( Scroll Down / Contrast Button ( )* )* Select / Auto Button (SELECT)* Power Switch ( )* D-SUB mini 15pin Connector DVI-D 24pin Connector Remote Control OSD Key Connector USB Connector Connector for AC Adapter Power Indicator NOTE Green: Normal operation Orange: Power Management * Remote Control OSD key is optional.
CONNECTING YOUR MONITOR NOTE The signal cables used for connecting the computer and monitor may vary with the type of computer used. An incorrect connection may cause serious damage to both the monitor and the computer. The cable supplied with the monitor is for a standard 15 pin D-Sub connector. If a special cable is required please contact your local iiyama dealer or regional iiyama office.
[Fitting and Removal of Cable Cover] ENGLISH Put a piece of soft cloth on the table beforehand to prevent the monitor from being scratched. Lay the monitor flat on a table with front face down. Step 2 Step1 Step2 < Removal > Move the stand into position as shown in Step1. Remove the cable cover as shown in Step2. Cable Cover Cable Hole < Fitting > As shown in Step3, connect the cables and put those through the cable holes. As shown in Step4, place the cable cover and fix it firmly using a screw.
COMPUTER SETTING Signal Timing Change to the desired signal timing listed on page 22: COMPLIANT TIMING. http://www.iiyama.com NOTE For additional information on how to download the driver for your touch screen monitor, please access the internet site noted above. Monitor Drivers are not required in most cases for Macintosh or Unix operating systems. For further information, please contact your computer dealer first for advice.
OPERATING THE MONITOR To create the best picture, your iiyama LCD monitor has been preset at the factory with the COMPLIANT TIMING shown on page 22. You are also able to adjust the picture by following the button operation shown below. For more detailed adjustments, see page 15 for SCREEN ADJUSTMENTS. Press the MENU Button to start the On Screen Display feature. There are additional Menu items which can be switched by using the / Buttons. ENGLISH CONTRAST BRIG HTNE S S 1280x1024 FH: 63KHz F V: 5 9 .
ADJUSTMENT MENU CONTENTS CONTRAST 1280x1024 FH: 63KHz F V: 5 9 . 9 H z Adjustment Item Button to Press Too dull Too intense CONTRAST BRIGHTNESS * Problem / Option Direct Too dark Too bright * Adjust the Brightness when you are using the monitor in a dark room and feel the screen is too bright. Direct You can skip the Menu items and display an adjustment scale directly by using the following button operations. BRIGHTNESS: Press the Button when the Menu is not displayed.
A U TO A D J U S T H-POSITION V-POSITION H-SIZE FINE Only Analog Input ENGLISH Adjustment Item AUTO ADJUST *1 Direct Problem / Option Adjust H/V-POSITION, H-SIZE and FINE automatically. H-POSITION Too left Too right V-POSITION Too low Too high H-SIZE *2 Too narrow Too wide FINE *2 Button to Press To correct flickering text or lines *1 For best results, use the Auto Adjust in conjunction with the adjustment pattern. See page 15 for SCREEN ADJUSTMENTS. *2 See page 15 for SCREEN ADJUSTMENTS.
OSD H-POSITION OSD V-POSITION OS D TI ME OU T RESET I N P U T S E LE C T Problem / Option Button to Press ENGLISH Adjustment Item OSD H-POSITION OSD is too left OSD is too right OSD V-POSITION OSD is too low OSD is too high OSD TIMEOUT You can set the OSD display duration time between 5 and 60 seconds. RESET Factory-preset data is restored. INPUT SELECT VGA Select the analog input. DVI Select the digital input.
9300 6500 5500 7500 USER ENGLISH Adjustment Item COLOR TEMP.
SCREEN ADJUSTMENTS The screen adjustments described in this manual are designed to set image position and minimize flicker or blur for the particular computer in use. The monitor is designed to provide the best performance at resolution of 1920 × 1080, but can not provide the best at resolutions of less than 1920 × 1080 because the picture is automatically stretched to fit the full screen. It is recommended to operate at resolution of 1920 × 1080 in normal use.
C Press the SELECT Button. (AUTO ADJUST) D Adjust the image manually by following procedure below when the screen has a flicker or blur, or the picture does not fit in the display area after performing the Auto Adjust. ENGLISH E Adjust the V-POSITION so that the top and bottom of the picture frame will fit to the display area. F 1) Adjust the H-POSITION so that the left side of the picture frame will move to the left edge of the display area.
NOTE In case the strong flicker or blurs remain on a part of the screen, repeat steps F and G because the H-SIZE may not be adjusted correctly. If the flicker or blurs still remain, set the refresh rate of computer to low (60Hz) and repeat steps from C again. Adjust the H-POSITION after the FINE adjustment if the horizontal position moves during the adjustment. H Adjust the Brightness and Color to get the desired picture after you complete the H-SIZE and FINE adjustments.
POWER MANAGEMENT FEATURE ENGLISH When your computer is not in use, the power management feature will automatically reduce the power consumption of your monitor. To use the feature, the monitor needs to be connected to a VESA DPMS compliant computer. There is a power management step the monitor takes as described below. The power management function, including any timer settings is configured by the operating system. Check your operating system manual for information on how this can be configured.
TROUBLE SHOOTING If the monitor fails to operate correctly, please follow the steps below for a possible solution. 1. Perform the adjustments described in OPERATING THE MONITOR, depending on the problem you have. If the monitor does not get a picture, skip to 2. 2. Consult the following items if you cannot find an appropriate adjustment item in OPERATING THE MONITOR or if the problem persists. 3.
RECYCLING INFORMATION ENGLISH For better environment protection please don't dispose your monitor. Please visit our web site: www.iiyama.com/recycle for monitor recycling.
APPENDIX Design and specifications are subject to change without prior notice. SPECIFICATIONS Touch Screen Technology LCD Panel Driving system ENGLISH Projected capacitive Light transmission 90% Communication USB serial transfer system Size Category 22" a-Si TFT Active Matrix Size Diagonal: 21.5" (55cm) Pixel pitch 0.247mm H × 0.
DIMENSIONS 517.5mm/20.4” 476.5mm/18.8” ENGLISH 219.0mm/8.6” 351.5mm/13.8” 268.0mm/10.6” 313.5mm/12.3” 46.0mm/1.8” 249.5mm/9.