5W battery-powered guitar amplifier with iOS/ USB interface.
Contents Table of Contents Contents 2 English 3 Safety information 3 iRig Micro Amp 3 Register your iRig Micro Amp 4 1 Installation and setup 4 1.1 Stand-alone 4 1.2 Device connected 8 2 USB LED 10 2.1 Audio input meter and gain 10 2.
English Safety information CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. iRig Micro Amp can ONLY be used with: • Consumer grade non-rechargeable CARBON-ZINC batteries • ALKALINE batteries • Consumer grade Ni-MH rechargeable batteries iRig Micro Amp Thank you for purchasing iRig Micro Amp.
English Register your iRig Micro Amp By registering, you can access technical support, activate your warranty and receive free JamPoints™ which will be added to your account. JamPoints™ allow you to obtain discounts on future IK purchases! Registering also keeps you informed of all the latest software updates and IK products. Register at: www.ikmultimedia.
English 2. Turn ON the unit. POWER 3. Connect your guitar to the instrument input of iRig Micro Amp.
English 4. It is now possible to adjust your sound with the on-board tune controls for each channel. The volume potentiometer controls the speakers output volume. 5. It is possible to connect an external sound source thru the 1/8” AUX IN, that allows you to play along your favourite songs.
English 6. Connect your headphones to the headphone output. This will mute the internal speaker of iRig Micro Amp. 1/8" HEADPHONES OUT 7. Connect an external speaker to the speaker output on the back of iRig Micro Amp. This will mute the internal speaker of iRig Micro Amp.
English 1.2 Device connected 1. Insert the AA batteries in the battery compartment or connect the (optional) PSU and turn on the unit. 2. Connect your guitar to the instrument input of iRig Micro Amp. 3. Connect the iRig Micro Amp to an iOS device or MAC/PC via the micro-USB connector. The USB LED will light up green to indicate that the USB is connected. 4. Download and launch the App. AmpliTube 4 iOS/Mac/PC FREE DOWNLOAD ikdownloads.
English 5. The input signal is now routed into the app, where the signal is processed, and from the app it will return to the iRig Micro Amp speaker. It is still possible to control the GAIN and VOLUME potentiometers on the control panel of iRig Micro Amp. 6. It is possible to connect an external sound source thru the 1/8” AUX IN, that allows you to play along your favourite songs. 7. Connect your headphones to the headphone output. This will mute the internal speaker of iRig Micro Amp. 8.
English 2 USB LED 2.1 Audio input meter and gain RED GREEN / ORANGE The USB LED will light up (GREEN) to indicate that a device is connected to the micro-USB port of iRig Micro Amp and acts as an audio input meter: LED GREEN: USB connected LED ORANGE: signal is present LED RED: clipping 2.2 Low battery The USB LED act also as battery indicator: when the batteries level is low, the LED starts blinking orange and batteries need to be replaced as soon as possible.
English 3 Specifications Common Speaker: 1x4” full range (4 Ohms) Output power: 15W (DC IN powered) or 7.5W (battery powered) Power supply Power: AA batteries (included) or DC IN (not included) Battery duration: approx. 15h with 6xAA alakline DC IN: 9V-15V DC negative inside USB Interface Conversion: 24-bit A/D, 24-bit D/A Sampling Rate: 44.1 kHz, 48 kHz, 88.2 kHz and 96 kHz Device Connection: micro-USB Instrument Input Connector: unbalanced, Hi-Z, TS 1/4” Jack.
English Warranty Please visit: www.ikmultimedia.com/warranty for the complete warranty policy. Support and more info www.ikmultimedia.com/support www.irigmicroamp.com Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.
Regulatory FCC statement This device complies with Part 15.107 and 15.109 Class B of the FCC Rules CFR47: October 2010. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
