20000003928 EUROSTAR_092014 IKA® EUROSTAR 20 digital IKA® EUROSTAR 40 digital IKA® EUROSTAR 60 digital IKA® EUROSTAR 100 digital IKA® EUROSTAR 20 high speed digital Operating instructions EN Reg.-No.
3 2 C C 4 1 B B A A Fig. 2 G J H K L M G I Fig. 3 Fig. 4 T N U U O P S Q R Fig. 6 G H Z G RH 3 I RH 5 W X V Fig.
EN Source language: German Contents Page EC-Declaration of conformity 3 Explication of warning symbols 3 Safety instructions 4 Correct use 6 Unpacking 6 Drive 6 Motor protection 6 Speed – normal operation 7 Speed – overload operation 7 Output shaft 7 Speed display 7 Commissioning 8 Securing 8 Switching on the instrument 9 Maintenance and cleaning 9 Error codes 10 Warranty 10 Accessories 11 11 Permitted IKA® stirrer tools Technical data 12 EC-Declaration of conformity We declare under our s
Safety instructions • Read the operating instructions in full before starting up and follow the safety instructions. • Keep the operating instructions in a place where it can be accessed by everyone. • Ensure that only trained staff work with the instrument. • Follow the safety instructions, guidelines, occupational health and safety and accident prevention regulations.
DANGER DANGER DANGER DANGER DANGER The operation of a free rotating shaft end is dangerous. Therefore, for safety reason, only insert through the stirring tool over the upper edge of housing at standstill. Wear your personal protective equipment in accordance with the hazard category of the medium to be processed, otherwise there is a risk of: - splashing of liquids - projectile parts - body parts, hair, clothing and jewelry getting caught.
Correct use • Use For mixing/stirring liquids with low to high viscosities by various stirring tools. This instrument is suitable for use in all areas except: - Residential areas - Areas that are connected directly to a low-voltage supply network that also supplies residential areas.
Speed – normal operation Speed - regulated (no variation in speed) The speed is monitored and regulated by processor controlled. The target speed is constantly compared with the actual rotation speed value of the output shaft and variations corrected. This guarantees a constant speed even if the viscosity of the substance being stirred changes. Fluctuations in mains voltage within the permitted tolerance range have no effect on the quality of regulation and constancy of speed.
Commissioning Assemble the overhead stirrer and all necessary accessories on a stable, even, non-slip surface. The EUROSTAR overhead stirrer must be secured to a stable stand (e.g. R 2722 or R 2723) with a crosssleeve (e.g. R 270). The stirring vessel must always be securely fixed for safety reasons. You must also ensure that the mounting device (stand) is set up in such a way that it is not liable to topple and does not start to move during the stirring procedure.
Switching on the instrument Check whether the voltage given on the type plate corresponds to the available mains voltage. The socket used must be earthed (fitted with earth contact). If these conditions have been met, the machine is ready for operation when the mains plug is plugged in. If these conditions are not met, safe operation is not guaranteed and the machine could be damaged. After switch on the main switch (A) as show in Fig.
Error codes The fault is shown by an error code in the display (C) as following if the error occurs, e.g. Er 4. Proceed as follows in such cases: F Switch the device switch (A) off. F Remove the stirrer tool and remove the instrument from the assembly. F Reduce the speed and switch on (instrument switch (A)) the device without the stirrer tool.
EUROSTAR 20 high speed digital • • • • • • • • • • • • • • EUROSTAR 100 digital • • • • • • • • • • • • • • EUROSTAR 60 digital EUROSTAR 40 digital R 1825 Plate stand R 1826 Plate stand R 1827 Plate stand R 2722 H-stand R 2723 Telescopic stand R 182 Cross sleeve R 270 Cross sleeve R 271 Cross sleeve RH 3 Strap clamp RH 5 Strap clamp FK 1 Flexible coupling R 301 Stirrer shaft protection R 301.
EUROSTAR 40 digital EUROSTAR 60 digital EUROSTAR 100 digital EUROSTAR 20 high speed digital Speed range under nominal load rpm EUROSTAR 20 digital Technical data 0/30-2000 0/30-2000 0/30-2000 0/30-1300 0/150-6000 Speed adjustment ------------------------------------ Stepless ------------------------------------ Speed display ------------------------------- 7-Segment LEDs ------------------------------- Speed setting accuracy rpm Speed measurement deviation Max.
IKA® - Werke GmbH & Co.KG Janke & Kunkel-Str. 10 D-79219 Staufen Tel. +49 7633 831-0 Fax +49 7633 831-98 sales@ika.de www.ika.