IKA ® 24 760 25 Operating instructions IKA® HS 501 digital IKA® KS 501 digital Table of Contents Page Spare parts diagram 2 Wiring diagram 2 List of spare parts 3 Guarantee 3 Scheduled use 4 Unpacking 4 Setting-up the instrument 4 Starting-up 4 Attachments 5 7 Maintenance and cleaning Technical data 7 使用说明 IKA® HS 501 数显型 振荡器 IKA® KS 501 数显型 振荡器 页码 目录 零配件图 2 接线图 2 零配件清单 3 保修 3 正确使用 8 开箱 8 安装 8 开机 8 夹具
Spare parts diagram & Wiring diagram / 零配件图和接线图 HS_KS 501 digital_092012 2
List of spare parts / 零配件清单 ldent-No. of Instrument 24 760 00 Item Designation 1 bottom plate 2 housing cover 3 shaking table 4 frame 1 5 frame 2 10 leaf spring 17 intermediate sheet metal 21 poly-V-belt 22 operating knob poti.
Scheduled Use By using different attachments, the IKA®-shakers HS 501 digital and KS 501 digital are suitable for mixing liquids in bottles, flasks, separating funnels, test tubes and dishes with a maximum shaking weight of 15 kg. The HS 501 digital produces a to and fro shaking motion and the KS 501 digital an orbital one. Unpacking Please unpack the instrument carefully and look out for any damage. It is important to recognize a transportation damage already when unpacking.
Attachments Attention: In shaking operations additional dynamic forces occur, and the instrument might start traveling on the table if the centre of gravity is unfavourably placed or if the bearing weight is too high. Single shaking vessels have to be placed into the centre, and several shaking vessels should be uniformly placed. Load limitations in the event of high shaking frequencies can be taken from the following diagrams. Universal Attachment AS 501.
*Attention: In case of max. assembly overhang of glass ware is possible. Danger of broken glass. The plate which can be equipped with clips of different size, is placed on the shaking table and fastened with the lateral quick-action vises. Dish Attachment AS 501.5 The dish attachment made of the environmentally friendly polystyrole, is simply slipped on the shaking table and pulled up for removal. Separating Funnel Attachments AS 501.2 and AS 501.3 AS 501.2 for 12 x 50 ml 10 x 100 ml 6 x 250 ml AS 501.
The attachments are placed on the shaking table and fastened with the lateral quick-action vises. Separating funnel attachments are only suitable for HS 501 digital. Maintenance and Cleaning The instrument requires no maintenance. Only the ball bearings are subjected to a natural wear. If the instrument needs to be repaired, it may only be opened by a qualified technician. If the instrument does not seem to function, please check the fuses first: Disconnect mains plug of instrument and open fuse holder.
正确使用 IKA® HS 501数显型振荡器和KS 501数显型振荡器可配置不同类型的夹具,适用 于烧瓶,长颈瓶、试管和培养皿等容器中液体的振荡,最大承载可达15kg。 HS 501数显型振荡器的振荡方式为往复运动,KS 501数显型振荡器的振荡方式 为圆周运动。 开箱 请小心拆除包装并检查仪器。 如果发现任何破损,请填写破损报告并立即通知货运公司。 安装 请将仪器置于平坦畅通的位置。 请确保在“技术参数”中规定的使用环境(温度,湿度等)下使用。 请避免阳光直照! 安全提示: 请将仪器置于平坦畅通的实验台上。 请勿在存在爆炸危险的室内操作该仪器。 开机 检查电源电压是否与铭牌电压相符,插座是否接地良好。若满足上述条件,则 可插上电源进行操作;否则则可能引发安全问题或者损坏仪器。 通过仪器前板的电位器“Mot“可选择振荡速度。 注意: 由于仪器开启时总是会以设定速度运行,因此启动前请将电位器“Mot“调至左手 边停止位置(最小速度)。 顺时针旋转时间旋钮可开启仪器。将旋钮调至I位置,仪器连续运转。仪器为无 级调速,定时范围为0-56分钟。通过时间旋钮可随时重置运行时间,但旋转位 置不能超过O位置
夹具 注意: 若放置重心偏移或负载过重,则在振荡过程中产生的额外动力因素会导致仪器 在桌面移动。因此,单个振荡容器必须置于振荡台中心,多个振荡容器则应均 匀地放置于振荡台。高频振荡情况下允许的负载范围请参考如下图表。 通用型夹具 AS 501.1 包括: 1 夹具座 6 固定棒 12 夹具座 AS 1.10 AS 1.11 AS 1.6 夹具座置于振荡台上,以侧边快速夹 钳固定。 固定夹摇板 AS 501.4 该摇板适用于: 容器固定夹数量和容量: AS 2.1 110 25 ml AS 2.2 55 50 ml 35 AS 2.3 100 ml 16 AS 2.4 250 ml AS 2.5 12 500 ml 8 1000 ml AS 2.
*注意:玻璃器皿过大的情况下可使 其悬于摇板。请注意玻璃破碎的危 险! AS 501.4 摇板可与不同大小的容器固 定夹配合使用。置于振荡台,由侧边 快速夹钳固定。 培养皿夹具 AS 501.5 分液漏斗夹具 AS 501.2 和 AS 501.3 AS 501.5 培养皿摇板由环保型聚苯乙 烯材料所制,易于下滑到振荡台也易 于上拉移除。 AS 501.2 数量和容量: 12 x 50 ml 10 x 100 ml 6x 250 ml AS 501.
夹具置于振荡台上,以侧边快速夹钳 固定。 分 液 漏 斗 夹 具 仅 适 用 于 HS501数 显 型。 清洁维护 仪器无需特别维护。只会发生轴承的自然磨损。若需维修,请仅由合格技术员 打开仪器进行维修。若发现仪器运转发生故障,请首先检查保险丝:使电源断 开并打开保险丝座。相关安全参数请参考“技术参数”中的“电源连接”。 请仅用如下试剂清洁仪器表面: a) 含活性剂的水溶液 b) 异丙醇 (如果非常脏的情况下)。注: 使用聚苯乙烯材料夹具的除外。 在送检仪器之前,请先清洁并确保仪器内无任何对人体健康有危害的物料残 留。 订购零部件时,请说明机器类型和零部件序号和订货号。 技术参数 230 V or 115 V 电源电压 电源频率 50/60Hz 电源连接 带保险丝的GEE测试插头: 230 V = 2 x 0,5 A; 115 V = 2 x 1 A 保护等级 (DIN 40 050) IP 21 工作制式 100% 定时 0-56 min 马达输入功率 70 W 马达输出功率 19 W 速度 0-300
IKA® - Werke GmbH & Co.KG Janke & Kunkel-Str. 10 D-79219 Staufen Tel. +49 7633 831-0 Fax +49 7633 831-98 sales@ika.de www.ika.