MS21 21.5" 3G-SDI Studio Monitor USER GUIDE www.ikancorp.com 1.713.272.8822 support@ikancorp.com © 2013 ikan Corporation.
Contents Safety Instructions................................................................................................3 Front......................................................................................................................4 Rear.......................................................................................................................6 MENU Description................................................................................................7 VIDEO.................
Safety Instructions • To help avoid damaging your monitor, connect only one power (AC or DC) in operation. • Rough handling of product may cause physical damage or malfunction. • Never insert anything metallic into the monitor openings. Doing so may create the danger of electric shock. • To avoid electric shock, never touch the inside of the monitor. Only a qualified should open the monitor’s case. • Openings in the monitor cabinet are provided for ventilation.
Front Standby (Power) Input Switcher (SDI 1, SDI 2, HDMI/DVI) Analog Switch analog input in the order of CVBS1 -> CVBS2 -> CVBS3 -> SVIDEO -> YPbPr -> RGB -> VGA. WF/VS Waveform / Vectorscope display selection button. Marker On/Off Frame line generation button. Scan Switch scan mode among Zero Scan, Under Scan, Over Scan, Pixel to Pixel in HD resolution. Zero Scan, Under Scan, Over Scan, Pixel to Pixel in SD resolution. H/V Delay Displays ancillary data by moving screen position.
Menu Enter Knob for Adjustment or Enter Knob used to adjust Brightness / Contrast / Chroma / Phase or Enter button.
Rear AC Input Please check Power Cord, Power Voltage, Supply power for power input are suitable for the standard before use. Please do not mix AC power and DC power as it may cause the defects or fire. DC Input For DC power supply. Check the DC Input voltage. In case of using the Battery power, DC 11 ~ 27V is usable. Update Port The Serial communication terminal that for changing the operating program(Firmware) of the body or controlling the monitor.
USB Port USB Firmware Update Port. MENU Description General Cautions for OSD menu or Display The menu may not be displayed even when user pressed Menu button if there's No Signal, or in unclear signal status. The menu selection may be saved for each input signal mode, so sometimes user should do menu selection again.
VIDEO Brightness, Contrast, Chroma, Phase, Sharpness Adjust color representation values. SDI Switching Normal : Use Normal in general condition but the screen might be blinking on screen change when you use Matrix or Routing Switcher. Fast : Use Fast to minimize blinking on screen change. NTSC Setup Select IRE among 0 or 7.5 (Default) HDMI UV Swap Sometimes color might be swapped on some HDMI input such as PC RGB. Turn this mode on to return to correct color.
DISPLAY 1 Aspect Set the aspect ratio of the screen. 16:9, 4:3, Native(Original) are selectable. This selection is ignored on 1080i, 1080p, 720p. 1:1 Scan On SD signals(Not HD), Set this on to display picture in 1:1 pixel mapping. AFD Turn this mode on to adjust aspect ratio with the ratio value in the source signal. Waveform Display Select waveform display mode. Choose Normal to analyze whole screen, choose Line Select to analyze a specific line of the screen.
Waveform Intensity Adjust waveform intensity. Waveform & Vector Size Adjust size of Waveform & Vector. Waveform & Vector Blend Adjust transparency value of Waveform & Vector. False Color Turn False Color mode on to check exposure levels of the picture.
DISPLAY 2 Exposure Range Check (Video Range Check) Checks Y, C level and displays over-exposed or under-exposed area on screen. The base value can be Y, Cb, or Cr. Y Range Max / Min Set Y range value for range check. C Range Max / Min Set C range value for range check. Blink Color The filled area color by range check can be either Black, Blue, Green or Red. Blink Time Set blinking time of the area between 1 to 5 seconds. Focus Assist Display Turns on Focus Assist mode.
Focus Assist Color Set brush color of focus assist mode among Blue, Green, and Red.
COLOR Color Temperature Select color temperature among 3200K, 5400K, 6500K, 9300K or USER. (Gain and Offset menu are displayed on USER temperature only) Red/Green/Blue Gain (USER mode only) R,G,B gains are adjustable on User mode. Red/Green/Blue Offset (USER mode only) R,G,B offsets are adjustable on User mode.
MARKER Marker Ratio Select one of preset markers or user marker. To display marker, press Marker button in front of the monitor. Center Marker Set preference to display center marker or not. Safety Area 16:9 Adjust size of the safety area when marker displayed on 16:9 screen. Safety Area 4:3 Adjust size of the safety area when marker displayed on 4:3 screen. Marker Color Select marker’s color among White, Red, Green, Blue, Gray and Black. Marker Mat Set how to display outside of the safety area.
User Marker H1 / User Marker H2 / User Marker V1 / User Marker V2 Set user marker’s position. H1 for left, H2 for right, V1 for top, V2 for bottom. The positions are saved as the selected marker name such as USER1.
OSD Timecode Display On/Off Timecode Position Set the position of timecode. OSD Display Time Set menu display time (seconds) MENU Position Set menu position among Left Top, Right Top, Left Bottom, Right Bottom and Center. V-Chip SD-SDI, Composite signal might contain V-Chip data. Turn this mode on to display V-Chip information on screen. Closed Caption Select one of 608 Line 21, 608 VANC, 608 Transcoded, 708 to display Closed Captions.
Service 1: general captions. Service 2: translated captions. Service 3,4: not assigned. CC608 StartLine Display line of captions are selectable by user. (e.g. 13) Internal Pattern Show internal test pattern such as color bars. Turn this mode off to display general pictures from input port. UMD Display Display UMD status. The screen aspect ratio will turn to 16:9 on this mode. UMD Color Set UMD color. UMD Edit Edit UMD text.
AUDIO Embedded Audio Left Select audio channel for left (Ch 1 ~ 15) Embedded Audio Right Select audio channel for right (Ch 2 ~ 16) Audio Level Meter Turns on/off audio level meters. Level Meter Size Select the size of the meters : Small or Large. Level Meter Position Select the position of the meters : Upper or Lower. Level Meter Direction Select Level Meter orientation among Horizontal or Vertical. Speaker Source Select the speaker output among Auto / SDI / Line In. For HDMI, use Auto mode.
GPI GPI Control Turns on/off external monitor control function. GPI Port 1,2,3,4,5,6 Assigns each GPI port’s function. (e.g. SDI 1 input, HDMI input, Tally Red) See EXTERNAL REMOTE CONTROLLING section for details. Remote ID Number Assigns the ID for the monitor to control through serial port. 0 to 99 can be assigned. Serial Remote Turns serial remote function on. All front buttons are locked on this mode. To exit from this mode, press and hold Menu button for 3 seconds.
SYSTEM Function 1,2,3,4 Assigns a function to each function button. See FRONT section for detail. Backlight Set the backlight intensity from 0 to 40. An LCD panel requires more than 30 minutes to be settled to a new backlight value. Front Button LED Set front LEDs on/off status. Font Button Lock Locks front buttons not to work. Press and hold Menu button for 3 seconds to exit from this mode. Update Firmware Turns update mode on. Select Serial or USB port for update.
Firmware Version This version number is required when you request for service. Operating Time This indicates total hours that the monitor operated.
External Remote Control Connecting GPI Port(RJ-45) Update Port (RJ-11) 1 2 3 4 5 6 Update (RJ-11) Update Terminal Assignment 1 PIN NC 4 PIN GND 2 PIN RX+ 5 PIN TX+ 3 PIN RX- 6 PIN TX- * Turn power off first and connect update cable when you update monitor firmware.
Assignable functions are listed below. Function Name Description SDI-1 Input Switches the input to SDI-1 SDI-2 Input Switches the input to SDI-2 HDMI Input Switches the input to HDMI YPbPr Input Switches the input to YPbPr CVBS-1 Input Switches the input to CVBS-1 CVBS-2 Input Switches the input to CVBS-2 CVBS-3 Input Switches the input to CVBS-3 KEY-UP ▲ CURSOR UP on Menu Control. KEY-DOWN ▼ CURSOR DOWN on Menu Control.
List of Compatible Video Formats (HDMI/Composite) NO Signal Input Formats INPUT Composite HD-YPbPr SD-RGB HDMI 1 NTSC O O 2 PAL O O 3 720*576/50i X O 4 720*480/59.94i X O 5 720*480/60i X O 6 720*576/50p X O 7 720*480/59.94p X O 6 720*480/60p X O 8 1280*720/23.98p X O 9 1280*720/24p X O 10 1280*720/25p X O 11 1280*720/29.97p X O 12 1280*720/30p X O 13 1280*720/50p X O 14 1280*720/59.
List of Compatible Video Formats (SDI) NO Input Signal Composite/ Formats S-Video Component YPbPr SDI RGB DVI 1 NTSC √ - - - - 2 PAL √ - - - - 3 525/60i (SD) - √ √ √ - 4 625/50i (SD) - √ √ √ - 5 720*480/59.94p - √ - - √ 6 720*576/50p - √ - - √ 7 1280*720/23.98p - - - - - 8 1280*720/24p - - - - - 9 1280*720/50p - √ - √ √ 10 1280*720/59.94p - √ - √ √ 11 1280*720/60p - √ - √ √ 12 1920*1035/59.
Specifications BSM-182 i Input Output I/O Port BSM-212 i 2 x BNC HD/SD-SDI, 1.485G/270M 3 x BNC Analog(YPbPr/CVBS/S-Video/RGB) 1 x HDMI HDMI (with HDCP v.1.1), 19pin Female 1 x DVI DVI-I, 24pin, Female 3 x BNC Analog(YPbPr/CVBS/S-Video/RGB) 2 x BNC HD/SD-SDI, 1.485G/270M 1 x Phone Jack In Line In(Stereo) 2 x Phone Jack Out Line Out(Stereo), H/P Out(Front, Stereo) 2 x Speaker Out 2W+2W, Stereo BSM-242 i Size 18.5” 21.
Dimensions BSM-182i (WxHxD) 438.4 x 310.8 x 66.4mm (17.2 x 12.2 x 2.6 inches) BSM-212i (WxHxD) 505.6 x348.0 x 59.2mm (19.9 x 13.7 x 2.3 inches) BSM-242i (WxHxD) 553.4 x 403.5 x 62.5 mm (21.7 x 15.8 x 2.
www.ikancorp.com CONDITIONS OF WARRANTY SERVICE • Free service for one year from the day of purchase if the problem is caused by manufacturing errors. • The components and maintenance service fee will be charged if the warranty period has expired. Free Service will not be Provided in the Following Situations: (* Even if the product is still within the warranty period.) • Damage caused by abuse or misuse, dismantling, or changes to the product not made by the company.