MICROWAVE HOOD COMBINATION INSTALLATION INSTRUCTIONS This product is suitable for use above electric or gas cooking products up to and including 36" (91.4 cm) wide. See “Installation Requirements” section for further notes. These installation instructions cover different models. The appearance of your particular model may differ slightly from the illustration in these installation instructions.
INSTALLATION REQUIREMENTS EG Ss es Tools Needed Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here. m Measuring tape Stud finder m Pencil mg . Masking tape or thumbtacks 7/16" socket wrench (or box wrench) for 1/4" x 2" lag screws m Scissors m No. 2 Phillips screwdriver bit for wood or metal gm an . No.
Installation Dimensions NOTE: The grounded 3 prong outlet must be inside the upper cabinet. See “Electrical Requirements” section. 12" (30.5 cm) min. 14" (35.6 cm) max. upper cabinet and side cabinet depth Electrical Shock Hazard 30" Plug into a grounded 3 prong outlet. == (76.2 cm) >, typical* Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. Observe all governing codes and ordinances.
INSTALLATION INSTRUCTIONS 4. Lift blower motor out of microwave oven. Remove [Viounting Plaje Depending on your model, the mounting plate may be in the foam packaging, or it may be attached to the back of the microwave oven. NOTE: To avoid possible damage to the work surface, cover the work surface. 1. Remove any remaining contents from the microwave oven cavity. 2. Ifthe mounting plate is attached to the back of the microwave oven, remove it and set it aside. 3.
Roof Venting Installation Only 1. Repeat Step 1 from “Wall Venting Installation Only.” 2. Repeat Step 2 from “Wall Venting Installation Only.” 3. Repeat Step 3 from 4. 5. Repeat Step 4 from “Wall Venting Installation Only. Rotate blower motor so that exhaust ports face the top of , . . ” “Wall Venting Installation Only. « . . ” microwave oven, and flat sides of blower motor face back of microwave oven. Lower blower motor back into microwave 6.
Locate Wail Stud(s) ae NOTE: If no wall studs exist within the cabinet opening, do not install the microwave oven. 1 Using a stud finder, locate the edges of the wall stud(s) within the opening. See illustrations in “Possible Wall Stud Configurations.” 2. Mark the center of each stud, and draw a plumb line down each stud center. See illustrations in “Possible Wall Stud Configurations.
5. With the support tabs facing forward (see illustrations in “Locate Wall Stud(s)” section), align the mounting plate center markers to the centerline on the wall, making sure its bottom edge is aligned to the horizontal line drawn in Step 3, and that the end holes are properly marked. Make sure the mounting plate is level. 6.
Installation for Wall Stud at One End Hole (Figure 3) 1. Drill a 3/16" (6 mm) hole into the wall stud at the end hole marked in Step 3 of “Mark Rear Wall.” 2. If installing on a second wall stud, drill a 3/16" (6 mm) hole into the wall stud at the other hole marked in Step 6 of “Mark Rear Wall.” Refer to Figure 3 in “Possible Wall Stud Configurations” in “Locate Wall Stud(s)” section. 3. Drill a 3/4" (19 mm) hole through the wall at the other end hole. 6.
5. Cut the 11%" (3.8 cm) diameter hole at the circular shaded area “@” on the template. This hole is for the power supply cord. I om, gus gregh he, 2 DL sg , ape OUT install ine Microwove Oven NOTE: If upper cabinet is metal, the supply cord bushing needs to be installed around the supply cord hole, as shown. AWARNING B Excessive Weight Hazard Use two or more people to move and install microwave oven. Failure to do so can result in back or other injury.
NOTE: If microwave oven does not need to be adjusted, skip steps 7-9. 7. If adjustment is required, rotate microwave oven downward. Using 2 or more people, lift microwave oven off of mounting plate, and set aside on a covered surface. 8. Loosen mounting plate screws. Adjust mounting plate and retighten screws. 9. Repeat steps 3-6. 2. Connect vent to damper assembly. A B : 10.
VENTING DESIGN SPECIFICATIONS This section is intended for architectural designer and builder/contractor reference only. NOTES: gm Vent materials needed for installation are not provided with microwave hood combination. We do not recommend To avoid outside, exhaust walls or using a Rectangular to Round Transition NOTE: The minimum 3" (7.6 cm) clearance must exist between the top of the microwave oven and the rectangular to round transition piece so that the damper can open freely and fully.
Recommended Vent Length A 3%" x 10" (8.3 x 25.4 cm) rectangular or 6" (15.2 cm) round vent should be used. 6" (15.2 cm) vent system = 73 ft (22.2 m) total The total length of the vent system including straight vent, elbows), transitions and wall or roof caps must not exceed the equivalent of 140 ft (42.7 m) for either type of vent. See “Recommended Standard Fittings” section for equivalent lengths. A B 6 ft (1.8m) Ww : For best performance, use no more than three 90° elbows.
SECURITE DE ENSEMBLE FOUR A MICRO-ONDES/HOTIE Votre sécurité et celle des autres est trés importante. Nous donnons de nombreux messages de sécurité importants dans ce manuel et sur votre appareil ménager. Assurez-vous de toujours lire tous les messages de sécurité et de vous y conformer. Voici le symbole d’alerte de sécurité. Ce symbole d’alerte de sécurité vous signale les dangers potentiels de décés et de blessures graves a vous et a d'autres.
Dimensions a respecter lors de I'installation eye 1 whe ie, sy, Deposea ra du gabaril de gecarion Pe buy ty Le morceau de carton du dessus de l'emballage du four a microondes est perforé. La partie a l'intérieur des trous de perforation est a utiliser comme gabarit de mur arriére. 1. 2. REMARQUE : La prise de courant a 3 alvéoles reliée a la terre doit étre située a l'intérieur du placard mural. Voir la section “Spécifications électriques”.
Spécifications bo!%, Ge INSTRUCTIONS DE LIAISON A LA TERRE e @ Pour tout appareil ménager connecté par un cordon de courant électrique : ll faut que le four a micro-ondes soit relié a la terre. En cas de court-circuit électrique, la liaison a la terre réduit le Risque de choc électrique risque de choc électrique car le courant électrique dispose d'un itinéraire direct d’acheminement a la terre.
3. Retirer les 2 vis fixant le moteur du ventilateur a l'arriére du four a micro-ondes. Pour une installation avec décharge a I'extérieur a travers le toit seulement co A. Vis (dans les trous décalés) 4. Soulever le moteur du ventilateur pour le sortir du four a micro-ondes. 1. Répéter I'étape 1 de “Pour une installation avec décharge murale seulement”. 2. Répéter |'étape 2 de “Pour une installation avec décharge murale seulement”. 3.
entifier identifi a la position du/d Cas SS f poteauGd) du cc olombage mural REMARQUE : S'il n'y a aucun poteau du colombage mural dans la zone délimitée par l'ouverture dans le placard mural, ne pas installer le four a micro-ondes. 4 1. Utiliser un détecteur magnétique de clou/vis pour localiser dans l'ouverture les rives du/des poteau(x) du colombage mural. Voir les illustrations a la section “Configurations possibles du colombage mural”.
race sur le mur arriere Le four a micro-ondes doit étre fixé sur au moins un poteau du colombage mural, et de préférence sur 2 poteaux; on utilise pour cela au moins 1 vis d'ancrage, et de préférence 2 vis. 1. 5. Utiliser un métre-ruban; déterminer et marquer clairement la position de l'axe central vertical de |'ouverture.
Percage Engager un écrou articulé sur chaque vis par l'arriére de la plaque de montage. Veiller a disposer de suffisamment d'espace pour que les écrous articulés puissent traverser le panneau de gypse et se déployer a l'intérieur de la cavité murale. dé trous cans le mur arriere En plus de la fixation sur au moins un poteau du colombage, on doit également fixer la plaque de montage sur le mur au niveau des deux trous d’angle.
6. Sil est possible de fixer également l'appareil poteau du colombage mural, insérer une vis l'autre trou percé a |'étape 2 du paragraphe face a un poteau du colombage mural” de la des trous dans le mur arriére”. sur un second d'ancrage dans “Un trou d’angle section “Percage 7. Contrdler l'alignement de la plaque de montage; veiller a établir un bon aplomb. 8. Serrer solidement la/les vis d'ancrage et le boulon. 5.
Ly 2 EP Wit UT A AVERTISSEMENT hn, Win, ia ipl, a) sig a, micro-onees 4. Alors que l'avant du four a micro-ondes est encore incliné, enfiler le cordon d'alimentation a travers le trou de passage percé dans le fond du placard mural. 5. Redresser le four a micro-ondes vers le placard mural. Risque du poids excessif Utiliser deux ou plus de personnes pour déplacer et installer le four 4 micro-ondes. Le non-respect de cette instruction peut causer une blessure au dos ou d'autre blessure.
| 7 A Ay Pour une installation avec décharge a>]!l'extérieur a> travers le toit seulement 1. ® ge a Achever linstallation 1. Insérer le module du clapet anti-reflux a travers |'ouverture Installer les filtres. Voir les Instructions d’utilisation pour la mise en place des filtres. découpée dans le placard mural, de telle maniére que la patte longue du module du clapet anti-reflux puisse glisser sous les pattes d'arrimage relevées de la plaque de support du clapet.
SPECIFICATIONS DU CIRCUIT D'EVACUATION Cette section présente de l'information de référence uniquement, a l'intention des architectes/concepteurs et constructeurs. REMARQUES : mg Les matériaux du circuit d'évacuation nécessaires a l’installation ne sont pas fournis avec l'ensemble four a microondes/hotte.
Longueur recommandée du circuit d'évacuation On doit utiliser un conduit rectangulaire de 344" x 10" (8,3 x 25,4 cm), ou un conduit rond de dia. 6" (15,2 cm). Circuit d’évacuation de dia. 6" (15,2 cm) = longueur totale 73 pi (22,2 m) La longueur totale du circuit d'évacuation, ceci incluant les sections de conduit rectilignes, coude(s), raccords de transition et bouche de décharge murale ou sur toit, ne doit pas dépasser l’équivalent de 140 pi (42,7 m) quel que soit le type de conduit.