Instruction manual
PPOOWWEERR OONNOOFFFF IIMMAAGGEE RREEVVEERRSSIINNGG CCIIRRCCUUIITT ________________________________________________
A single control on the housing operates both the Power ONOFF and Image
Reversing Circuit
Secure the camera to the tray and partially slide the camera and tray inside the
housing so you can connect the cable from the PowerImage Reversing circuitry to
the AV Out port on the camera
PPoowweerr OONNOOFFFF SSwwiittcchh
If the camera is OFF hold the Power button down for one second to turn the
camera ON When turning the camera OFF there is a minute standby power down
delay that occurs when the reversing circuit is ON during power down To avoid the
minute power down delay turn the Reversing Circuitry OFF and then hold the the
Power button down for three seconds to turn the camera OFF
IImmaaggee RReevveerrssiinngg CCiirrccuuiitt
The circuit reverses flips the image and words on the LCD screen so that when
the image is reflected in the external mirror it appears correct lefttoright
FFuunnccttiioonnss LLoocckkeedd OOuutt
When the reversing circuit is ON some camera functions may be locked out To
activate the locked out functions temporarily turn the Reversing Circuit OFF change
the locked out function on the camera and then turn the Reversing Circuit back ON
SSttiillll MMooddee
When in Still Mode and full wide angle the image may show vignetting shading
in the corners To correct slightly zoom in on the image until vignetting disappears
FFIINNAALL PPRREEPPAARRAATTIIOONN
__________________________________________________________________________________________________________
Remove the lens cap and cord from the camera
Otherwise they may interfere
with the housing seal
The cameras auto focus feature is utilized underwater For best results move in
close to your subject and use the wide angle range to shoot thru as little water as
possible The full zoom range is accessible underwater
Turn the cameras builtin flash OFF
Chart shows recommended initial settings
underwater
WWHHIITTEE BBAALLAANNCCEE
__________________________________________________________________________________________________________________
Initially set the white balance to Auto Use the touch screen controls on the
housing to change white balance
CCoolloorr FFiilltteerr::
When using the color filter during the day set camera white balance
to Auto for foot depth For foot depth set white balance to Outdoor
VViiddeeooLLiittee::
When using optional Video Lite at NIGHT set the camera white balance
to the Indoor position During the DAY use the Outdoor setting for subjects beyond
feet and the Indoor setting for closer subjects
CCAAMMEERRAA SSEETTTTIINNGG
Power OnOff Camera On
Zoom Lever Wide Angle Setting
Focus Auto Mode
Exposure Auto Mode
Program AE Auto Mode
Shutter Speed Normal
White Balance Auto Mode see section
Steady Shot Off
Builtin Flash Off
II NN SS TT AA LL LL AA TT II OO NN
CCAAMMEERRAA TTRRAAYY
________________________________________________________________________________________________________________________
The camera mounts to the tray which extends from the back plate of the
housing
DDOO NNOOTT
remove the tray from the back plate
Position the camera against the two stabilizing
pins on the tray and secure with the camera
mounting bolt The camera should fit easily on the
tray and should be parallel with the sides of the tray
IINNSSEERRTTIINNGG TTHHEE CCAAMMEERRAA
__________________________________________________________________________________________________
Check that the oring is clean and properly positioned on the lip of the clear
housing back plate Check that the lens shade is completely threaded into the camera
Once the camera is mounted to the tray as shown above pull the housing
controls out to provide clearance for installing the camera Partially slide the camera
into the housing so you can connect the reversing circuit cable to the AV Out port on
the camera When sliding the camera into the housing align the housings zoom con
trol to accept the cameras zoom lever Make sure the lens shade on the front of the
camera fits into the port recess in the front of the housing
DDOO NNOOTT
force this installation; the camera and tray should slide easily into place
so the housings back plate oring is resting against the main housing body In this
position the lid snaps can be positioned over the lid hooks on the housing back plate
and snapped into position to seal the housing
HHOOUUSSIINNGG CCOONNTTRROOLLSS
__________________________________________________________________________________________________________
Slide the housing controls back in place making sure they properly align with the
camera functions
Operate each control to see how it works with the camera Some controls such
as startstop will be used frequently Other controls may seldom be utilized Refer to
your camera owners manual for the proper function of each camera control Look
thru the back to be sure that you can see into the viewfinder
When using the housing controls especially the startstop do NOT use excessive force
because you could damage the camera
CCAAUUTTIIOONN
Remove the lens cap and cord from the camera Otherwise the cord may
interfere with the housing seal
If the housing controls are not properly positioned they could interfere with the housing seal
MMAANNUUAALL FFOOCCUUSS OOPPEERRAATTIIOONN
__________________________________________________________________________________________
Manual focus may be preferred in low light levels or when the subject possesses
little contrast Set the focus pad on the LCD screen to Manual to cancel the auto
focus If you want to manually adjust the focus rotate the manual focus control as
desired
To reactivate the auto focus set the focus pad on the LCD screen to Auto
IIKKEELLIITTEE UUNNDDEERRWWAATTEERR SSYYSSTTEEMMSS
West rd Street • PO Box • Indianapolis IN USA •
Email: ikelite@ikelitecom
• wwwikelitecom
Camera Mounting Bolt
Camera Tray
O
’ring
Back Plate
Stabilizing
Pins