User’s Guide for Model IAHRF79 v2258-01
FCC WARNINGS SAFETY WARNINGS • WARNING: Where the mains plug or appliance coupler is used as the disconnect device, such disconnect device shall remain readily operable. WARNING: To assure continued operation, follow the attached installation instructions and use only shield cables when connecting to other devices. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. • Risk of electric shock.
TABLE OF CONTENTS Introduction - 4 Features Includes Overview Headphones - 5 Base - 6 Control Functions - 7 LED Indicator Lights - 7 Setup Base Power - 8 Headphone Charging - 9 Digital Optical Audio - 10 RCA Stereo Audio - 11 Coaxial Audio - 12 Line In - 13 Listening Pairing the Headphones to the Base - 14 Troubleshooting - 15 Customer Support - 16 Contact Information International Support Warranty Information 3
INTRODUCTION Trying to do some around-the-house chores and still want to listen to the TV or your favorite music? These wireless headphones allow freedom of movement while maintaining excellent reception. Features »» Digital 2.4GHz wireless connection »» Up to 100ft transmission distance without line of sight limitations »» Compatible with any media device with a 3.
OVERVIEW Headphones 1. LED Indicator 2. Power/Pair Button 3. Volume Control 4. Aux In (3.5mm audio input) 5. Micro-USB DC Charging Port 6.
OVERVIEW Base 7. Charging Contacts 8.
Control Functions »» Power Press and hold to power ON and OFF. »» Volume Press up or down to adjust volume level. »» Pair Press to pair to the headset base (see pg. 14 for pairing procedure).
SETUP Base Power Connect the DC Power Input on the base to a standard power outlet using a DC Power Adapter (included). The base must be connected to a power source and powered ON to transmit audio to the headphones.
Headphone Charging There are two ways to charge the headphones. »» Place the headphone on the base so that the charging contacts are aligned. »» Use a Micro-USB to USB cable (included) to connect the DC Input (MicroUSB) on the headphones to the USB port on a powered on computer or USB power adapter (not included). A fully charged battery will provide up to 7 hours of playtime. Battery life will improve at lower volume levels and decrease at higher volume levels.
CONNECTING AUDIO Digital Optical Audio Requires a media source with an Optical Audio Output and a Digital Optical Audio Cable (included). 1. Using a Digital Optical Audio Cable, connect the Optical Output on your media source (TV, amplifier, etc.) to the Optical Input on the base. 2. On the connected media source (TV, amplifier, etc.), make sure the audio settings are set to PCM or Optical Audio. 3. Audio played through the connected media source (TV, amplifier, etc.) will now be sent through the base.
RCA Stereo Audio Requires a 3.5mm to RCA stereo audio cable adapter and a 3.5mm audio cable (included). When connecting an RCA stereo audio cable (Red/White), match the colored plugs to their corresponding ports. 1. Using a 3.5mm to RCA Stereo Audio Cable (included), connect the RCA Stereo Output on your media source (TV, amplifier, etc.) to the Aux In (3.5mm audio input) on the base. 2. Audio played through the connected media source (TV, amplifier, etc.) will now be sent through the base. Aux In R 3.
CONNECTING AUDIO Coaxial Audio Requires a media source with a Coaxial Audio Output and a Coaxial Audio Cable (not included). 1. Using a Coaxial Audio Cable, connect the Coaxial Output on your media source (TV, amplifier, etc.) to the Coaxial Input on the base. 2. On the connected media source (TV, amplifier, etc.), make sure the audio settings are set to Coaxial Output. 3. Audio played through the connected media source (TV, amplifier, etc.) will now be sent through the base.
Line In Requires a 3.5mm audio cable (included). 1. Connect a 3.5mm audio cable to the Line In on the base or the headphones and the audio output/headphone jack on an audio device.
LISTENING Pairing the Headphones to the Base Note: After the initial pairing, the headphones will stay paired to the transmitter base. It will not be necessary to reconnect each time you use the headphones. 1. Press and hold the Power/Pair button to power on the headphones. 2. Press the Power/Pair button again to begin pairing. The headphones will automatically detect the base and connect to it. 3. After a successful connection, the LED on the headphones will slowly blink blue.
TROUBLESHOOTING PROBLEM POSSIBLE SOLUTION Unit will not power on »» Make sure the headphones’ battery is charged. Recharge if needed. Audio distortion »» Volume on the headphones or the connected device may be too high. Reduce the volume of one or both of the devices. Headphones won’t play or fails to connect »» Make sure the volume on the headphones is turned up to an audible level. »» Make sure the headphones’ battery is charged and they are powered on. »» Stay within 3 ft.
CUSTOMER SUPPORT Contact Information Warranty Information Website: www.iLiveElectronics.com Email Support: prodinfo@dpiinc.com Email Parts: partsinfo@dpiinc.com Phone Support: 1-888-999-4215 For Warranty Information and the most up-to-date version of this User’s Guide, go to www.iLiveElectronics.com. International Support To download this User’s Guide in English, Spanish, or French, or to get answers to frequently asked questions, visit the support section at: www.iLiveElectronics.
