Industrial BLDC Ceiling Fan Owner’s Manual Model No.
TABLE OF CONTENTS General Safety Instructions………………………………....….......……. 3-4 Specifications ………………………......................... .......................... 4 Parts of the ceiling fan ..............……………………….…….......…....… 5-7 Installation Instructions …………………….............….…….......…....… 8-14 Remote Control & Operating Instructions …………………..……....… 15-17 Maintenance and Cleaning ……………………………....................…. 18 Troubleshooting …………………………………………...................….
GENERAL SAFETY INSTRUCTIONS Read instructions carefully before assembling or installing your fan. It is important that you observe all safety information to help prevent personal injury and/or property damage. 1. Installation work and electrical wiring should be done by qualified person only in accordance with all applicable codes and standards. 2. All wiring and installation procedures must satisfy National Electrical Codes (ANSI/ NFPA 70) and Local Codes. 3.
body, it can cause severe internal burns and can lead to death in as little as 2 hours. Always completely secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the batteries, and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention. Suitable for Commercial or Industrial Use Only.
PARTS OF THE CEILING FAN REF QTY DESCRIPTION SP-HVLS-1 1 Mounting Bracket SP-HVLS-2 1 Downrod/Ball Joint Assembly SP-HVLS-3 1 Canopy SP-HVLS-4 1 Canopy Cover SP-HVLS-5 1 Downrod Cover SP-HVLSxxx-6 1 Motor Assembly SP-HVLS-7 1 Fan Blade Holder SP-HVLSxxx-8 9 Fan Blade SP-HVLS-9 9 Fan Blade Cap SP-HVLS-10 9 Fan Blade Screw Cover SP-HVLS-11 1 Bottom Cover SP-HVLS-1 SP-HVLS-2 SP-HVLS-3 Note: xxx = Fan Blade size, 72, 88, 96, 108 SP-HVLS-4 SP-HVLS-5 SP-HVLS-7 SP-HVLS-10
H7 REF QTY DESCRIPTION H1 2 10# 32x3/4 SCREW H2 3 WIRE CAPS H3 1 3/16 * 2 INCH WOOD SCREW +Ф5.5xФ25xT1.
Dimensions (inch) Model# D H ILG8HVLS72 72 16-3/4 ILG8HVLS88 88 16-3/4 ILG8HVLS96 96 16-3/4 ILG8HVLS108 108 14 7
INSTALLATION INSTRUCTIONS WARNING To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before hanging. (Figure 1) NOTE: If you are not sure if the outlet box is grounded, contact a licensed electrician for advice, as it must be grounded for safe operation. WARNING The fan must be hung with at least 10´ of clearance from floor to blades. (Figure 2) WARNING The outlet box must be securely anchored and capable of withstanding a load of at least 35 lbs.
Before installation, check that the outlet box is securely installed in place and it is able to support at least the fan weight. Securely attach the mount bracket to ceiling outlet box acceptable for ceiling fan support. Leveled Ceiling Mounting Angled Ceiling Mounting Attention Install the ceiling fan in a location such that the spacing from the tip of the blades to the nearest objects or walls is AT LEAST 12” (300mm).
Install the fan assembly to the mount bracket as shown below: Route wires and safety cable through downrod cover, canopy cover and ceiling canopy. Install the downrod with motor assembly through the canopy, canopy cover and downrod cover. Remove the two set screws from the downrod and retain for reinstallation. Install the(H4) mounting pin by aligning the holes in the downrod support with holes in the downrod. Secure pin with (H6) cotter pin.
Install the fan assembly to the mount bracket as shown below. Rotate till notch on the ball joint catches the stopper on the mounting bracket.
Connect wires to supply/grounding wires using connectors as shown below. Attach the safety cable with (H3) 3/16 * 1-1/2 inch wood screw +Ф5.5xФ25xT1.5 lock washer to the ceiling . Conductor of a fan identified as grounded conductor to be connected to a grounded conductor of power supply, conductor of fan identified for equipment grounding to be connected to an equipment-grounding conductor.
Remove the two screws from the mount bracket. Assemble the canopy by tighten the screws. Securely attach and tighten the canopy cover. Rotate canopy until lock pin of mounting bracket is engaged with canopy, then tighten the screws till the keyhole is locked. Install the fan blade cap to the fan blade with (H9) M4x6mm long screw and (H10) Ф4 plain washer. Repeat this step for all 9 fan blades. Install the fan blade screw cover to the fan blade with (H12) M5x8mm long screw and (H11) Ф5 lock washer.
Assemble the fan blade to the fan blade holder with (H5) M5x10mm long screw and (H11) Ф5 lock washer. Repeat this step for all 9 fan blades. Rotate the bottom cover to the fan assembly until tighten.
REMOTE CONTROL & OPERATION Button Description Power ON/Off 1 Speed 1 (Minimum) 2 Speed 2 3 Speed 3 4 Speed 4 5 Speed 5 6 Speed 6 (Maximum) Direction Control (Clockwise/Counterclockwise） 2H 4H 8H Timer Setting HOW TO INSERT BATTERY NOTE: Remove the batteries if the remote control is not to be used for a month or more. Batteries left in the unit may leak and cause damage.
REMOTE CONTROL OPERATION INSTRUCTIONS (1) After the ceiling fan has been installed according to the assembly procedure and connected according to power supply specifications, perform the remote control and ceiling fan pairing procedure (refer to the remote control pairing method below). (2) After the pairing has been completed, you can use the remote control to turn on/off the ceiling fan, and select speed. OPERATING INSTRUCTIONS Remote control pairing procedure: 1.
5. Direction control Press the Direction Control can change the fan blade rotate direction. When the fan blade rotates clockwise (Summer Mode) and the air will blow down. A downward air flow creates a cooling effect.This allows you to set your air conditioner on a higher temperature setting without affecting your comfort. When the fan blade rotates counterclockwise (Winter Mode) and the air will blow up. An upward airflow moves warm air off the ceiling area.
MAINTAINANCE 1. Because of the fan’s natural movement, some connections and screws may become loose. Check the support connections, brackets, and blade attachments at least twice a year to make sure they are secure. 2. Clean the fan periodically to help maintain the appearance. Do not use water when cleaning. This could damage the motor, or possibly cause electric shock. 3. Use only a soft brush or lint-free cloth to avoid scratching the finish. 4. There is no need to oil your fan.
Warranty Information This product comes with a 1-YEAR LIMITED COMPONENT WARRANTY. If your unit does not appear to be working properly, please contact our service center by calling 1-800-317-1688. Prior to your call, we encourage you to visit our service related website www.ilivingusa.com for troubleshooting tips and service instructions if needed. Register your product at our website: Or visit iLivingUSA.com/register-product Feedback Love it? Help us make the product more for you.
