SHUTTER MOUNTED EXHAUST FAN 1
Models: ILG8SF7V/ILG8SF10V/ILG8SF12V/ILG8SF16V ILG8SF18V/ILG8SF18S/ILG8SF20V/ILG8SF24V ILG8SF30S/ILG8SF36S OWNER'S MANUAL PLEASE READ AND SAVE THESE INSTRUCTIONS 2
PLEASE READ AND SAVE THESE INSTRUCTIONS. READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE, OR MAINTAIN THE PRODUCT DESCRIBED. PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION. FAILURE TO COMPLY WITH INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PRO PROPERTY PERTY DAMAGE! RETAIN INSTRUCTIONS FOR FUTURE REFERENCE. BEFORE YOU BEGIN WARNING! Installation, trouble shooting, and replacement of parts are to be performed only by authorized service technicians.
Inspect: • After unpacking fan, carefully inspect for any damage that may have occurred during transit. Check for loose, missing, or damaged parts. • Check all bolts, screws, set-screws, etc. for looseness that may have occurred during transit. Tighten as needed. Rotate propeller by hand to ensure it turns freely. • See General Safety Instructions on page 3, and Cautions and Warnings as shown. GENERAL SAFETY INSTRUCTIONS Fans are UL/CUL Listed, Standard 705. 1.
connected load. 9. Protect the power cable from coming in contact with sharp objects. 10. Do not kink or create tight bends in the power cable and never allow the cable to come in contact with oil, grease, hot surfaces, or chemicals. 11. Make certain that the power source conforms to the requirements of your specific exhaust fan model. The fan frame and motor must be electrically grounded to a suitable electrical ground, such as a grounded water pipe or ground wire system. 12.
2. Install any auxiliary components such as thermostats, switches, or speed controls. 3. Connect power to the motor using an approved wiring method. Refer to the following wiring diagrams: diagrams Figure 1 & Figure 2. Fan frame and motor must be securely and adequately grounded to a suitable electrical g ground, round, such as a ground water pipe or ground wiring system. Figure 1: Wiring Diagram - Speed Controllable. 115-volt volt connection.
Figure 2: Wiring Diagram - Single speed. 115-volt connection.
GENERAL SPECIFICATIONS Power source Mounting Position 115V, 60Hz Vertical Frame Material Galvanized Steel Shutter Blade Material Aluminum Alloy Propeller Material Aluminum Alloy and Galvanized Steel Agency Compliance UL/CUL 705 Dimensions (Inches) 9
Figure 3 MODEL Prop. Dia.
ILG8SF36S 36" 1/2 6.00 825 Ball 8.24 6128 4380 2620 OPERATING INSTRUCTIONS 1. Keep the area free of objects that could impede air flow on both the intake and exhaust side of fan. 2. For proper exhaust operation, a window, door, or louver should be opened for fresh air intake on the opposite side of the area to be ventilated. 3. Turn the fan ON; the shutter will open automatically. When the unit is turned OFF, the shutter will close. 4.
1. Disconnect power source before servicing. 2. Periodically clean off accumulated dirt from the propeller, guard, motor, and shutter. Do not depend on any switch as the sole means of disconnecting power when installing or servicing. If power disconnect is not ot visible, utilize OSHA Lock out/Tag out procedure. Failure to do so may result in fatal electrical shock. Employ proper lock-out/tag out/tag-out out procedures when performing maintenance.
Defective motor Replace motor Switch in OFF position Turn switch ON Blocked intake or exhaust opening Clear intake and exhaust openings of any obstructions. Clean motor, guard, propeller, and shutter assembly. Increase the opening of the fresh air intake. Insufficient air flow Low voltage Check electrical wiring. Speed control set too low Increase speed with controller iLIVING USA 239 Harbor Way South San Francisco, CA 94080 Tel: 800-317-1688 Email: service@ilivingusa.
Check out our website: www.ilivingusa.