MULTI-SPEED SHUTTER MOUNTED EXHAUST FAN WITH THERMOSTAT Models: ILG8SF10V-T/ILG8SF12V-T/ILG8SF14V-T/ ILG8SF16V-T/ILG8SF18V-T/ILG8SF20V-T/ ILG8SF24V-T/ILG8SF30V-T OWNER'SMANUAL PLEASE READANDSAVETHESEINSTRUCTIONS 1
PLEASE READ AND SAVE THESE INSTRUCTIONS. READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE, OR MAINTAIN THE PRODUCT DESCRIBED. PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION. FAILURE TO COMPLY WITH INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE! RETAIN INSTRUCTIONS FOR FUTURE REFERENCE. BEFORE YOU BEGIN WARNING! Installation, troubleshooting, and replacement of parts are to be performed only by authorized service technicians.
IMPORTANT SAFETY INSTRUCTIONS Fans are UL/CUL Listed, Standard 507. 1.Do not depend on any switch as the sole means of disconnectingpower when installing or servicing the fan. 2.Always disconnect, lock-out, and tag-out power source before installing or servicing. Failure to disconnect power source can result in fire, shock, or serious injury. 3. Motor will restart without warning after thermal protector trips. Do not touch operating motor; it may be hot enough to cause injury. 4.
INSTALLATIONINSTRUCTIONS WARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TOPERSONS, OBSERVE THE FOLLOWING: a) Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer. b) Before servicing or cleaning unit, switch power off at service panel and lock the servicedisconnecting means to prevent power from being switched on accidentally.
Wooden Plank Minimum Thickness Fan Model 10mm All Models Screw Size Screw Picture 3/16“ x 1-1/4“ 3. Please ensure the space has a gap for enough air to get into the space. The fan installed on free space of at least 100mm above the upper edges of the corner. Air Flow WARNING: This fan is recommended to be mounted by a qualified electrician. Fan frame and motor must be securely and adequately grounded to a suitable electrical ground, such as a ground water pipe or ground wiring system.
Wiring Diagram Thermostat Temperature Range: 32˚F~130˚F (0˚C~54˚C) For ILG8SF10V-T/ILG8SF12V-T/ ILG8SF14V-T For ILG8SF16V-T 6
For ILG8SF18V-T For ILG8SF20V-T/ ILG8SF24V-T For ILG8SF30V-T 7
Power source Mounting Position Frame Material Shutter Blade Material Propeller Material Agency Compliance 115V, 60Hz Vertical Galvanized Steel Aluminum Alloy Aluminum Alloy and Galvanized Steel UL/CUL 507 Dimensions(Inches) For ILG8SF10V-T/ ILG8SF12V-T/ ILG8SF14V-T 8
For ILG8SF16V-T/ ILG8SF18V-T/ ILG8SF20V-T/ ILG8SF24V-T/ ILG8SF30V-T MODEL Prop. Dia.
OPERATING INSTRUCTIONS 1. Keep the area free of objects that could impede air flow on both the intake and exhaust side of fan. 2. For proper exhaust operation, a window, door, or louver should be opened for fresh air intake on the oppositeside of the area to be ventilated. 3. Connect power plug to any standard 115-volt AC outlet. Caution: Make sure the SpeedControl is in the OFF position. 4. Use the pull chain switch to select the desired operating speed. The speed runs as HIGH---MID---LOW--- OFF. 5.
MAINTAINANCE AND CLEANING 1. Disconnect power source before servicing. 2. Periodically clean off accumulated dirt from the propeller, guard, motor, and shutter. Do not depend on any switch as the sole means of disconnecting power when installing or servicing. If power disconnect is not visible, utilize OSHA Lock out/Tag out procedure. Failure to do so may result in fatal electrical shock. Employ proper lock-out/tag-out procedures when performing maintenance.
iLIVING USA 9293 Beatty Dr Sacramento, CA 95826 Tel: 650-952-2257 Email: service@ilivingusa.com Like us on Facebook: https://www.facebook.com/ilivingusa/ Follow us on Twitter: @iLIVINGUSA Check out our website: www.ilivingusa.
