Instructions / Assembly

ManualsBrandsIlluminations ManualsChristmas Decorations6 ft. 130-Light RGB LED Multi-Color Color Blast Remote Controlled Cone Tree

OWNER′S MANUAL

DISTRIBUTED BY: Polygroup

Trading Limited

Unit 606, 6/F, Fairmont House, 8 Cotton Tree Drive, Central, Hong Kong

1. Before using or reusing, inspect the product carefully. Discard any products that have cut, damaged or frayed wire

insulation or cords, cracks in the lampholders or enclosures, loose connections, or exposed copper wire.

2. When not in use, store in a cool, dry location protected from sunlight.

USE AND CARE INSTRUCTIONS

READ, AND KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE

FAILURE TO FOLLOW THESE WARNINGS AND INSTRUCTIONS CAN RESULT IN SERIOUS INJURY OR DEATH TO USERS, ESPECIALLY CHILDREN.

IMPORTANT SAFETY INSTRUCTIONS

When using electrical products, basic precautions should always be followed including the following:

READ AND FOLLOW ALL SAFETY INSTRUCTIONS.

2. Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use. When used outdoors,this product must be

connected to a Ground Fault Circuit Interrupting (GFCI) outlet. If one is not provided,contact a qualified electrician for proper installation.

3. This seasonal use product is not intended for permanent installation or use.

4. Do not mount or place near gas or electric heaters, fireplace, candles or other similar source of heat.

5. Do not secure the wiring of the product with staples or nails, or place on sharp hooks or nails.

6. Do not let lamps rest on the supply cord or on any wire.

7. Unplug the product when leaving the house, or when retiring for the night, or if left unattended.

8. This is an electric product - not a toy! To avoid risk of fire, burns, personal injury and electric shock, it should not be played or placed where

small children can reach it.

9. Do not use this product for other than its intended use.

10. Do not hang ornaments or other objects from cord, wire, or light string.

11. Do not close doors or windows on the product or extension cords as this may damage the wire insulation.

12. Do not cover the product with cloth, paper or any materials not part of the product when in use.

13. This product can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or

lack of experience and knowledge if they have been given supervision or instruction concerning use of the product in a safe way and

understand the hazards involved. Children shall not play with the product. Cleaning and user maintenance shall not be made by children

without supervision.

14. The supply cord, adaptor, plugs and/or connectors cannot be replaced or modified. If either is damaged, the product should be scrapped.

15. Strobe lights have been known to trigger seizures in people with photosensitive epilepsy.

16. Read, and follow all instructions that are on the product or provided with the product.

17.

SAVE THESE INSTRUCTIONS.

CAUTION:

1. To reduce the risk of fire or electric shock:

• Do not install on trees having needles, leaves or branches covering of metal or materials which look like metal;

• Do not mount or support cords or cables in a manner that can cut or damage wire insulation;

• Do not attempt to replace lamps or modify string;

• Use only the adaptor provided with this product, and

• This product does not contain lamp shunts, which allow the product to operate if one lamp burns out.

2. Make sure connectors are fully inserted and any connector rings are twisted until completely secured such that the ring can no longer be

turned and the two portions of the connectors are completely assembled.

3. The lighting string is rated 10W (0.42A). Do not overload. To avoid the risk of fire or personal injury, do not exceed the maximum allowable

electrical load.

Cone Tree LED Lights

Rated Wattage: 10W (0.42A), Total Wattage: 11.3 Watts

This product is not extendable. Do not connect with other light products.

AC Adaptor

Input: 120V/60Hz, 0.25A

Output: DC 24V, 0.54A

WARNING

ILLUMINATIONS

COLOR BLAST

REMOTE CONTROLLED LED LIGHTS

CONE TREE LED LIGHTS

Summary of content (4 pages)

PAGE 1
OWNER′S MANUAL ILLUMINATIONSTM COLOR BLAST TM REMOTE CONTROLLED LED LIGHTS CONE TREE LED LIGHTS READ, AND KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE FAILURE TO FOLLOW THESE WARNINGS AND INSTRUCTIONS CAN RESULT IN SERIOUS INJURY OR DEATH TO USERS, ESPECIALLY CHILDREN. WARNING IMPORTANT SAFETY INSTRUCTIONS When using electrical products, basic precautions should always be followed including the following: 1. READ AND FOLLOW ALL SAFETY INSTRUCTIONS. 2.
PAGE 2
OWNER′S MANUAL PARTS LIST (1) Tree Stand Frame x 1 (2) Tree Stand Bases x 5 (3) Tree Stand Rod x 5 (4) Tree Pole x 4 (5) Light String Module & Tree Top Star x 1 (6) Power Adaptor x 1 (7) Ground Stake x 5 SETUP INSTRUCTIONS 2 1. Take the product out from the box. 2. Insert the legs of the Tree Stand Frame into the Tree Stand Bases, and pull apart the legs until they snap and form a star shape. 3. Slot the Tree Stand Rods into the Tree Stand Bases until firmly secured. 4.
PAGE 3
OWNER′S MANUAL SETUP INSTRUCTIONS 5. Insert Tree Top Star into the round base of Light String Module. Then secure the base onto the toppest Tree Pole. 6. Let the light strings hang down, and attach the end of strings to the hooks on Tree Stand Rods. 7. Place the tree at your desired spot. To secure, you can insert the Ground Stakes through the holes of the Tree Stand Bases into the soil or lawn. 8. Plug it in to the wall outlet. 9. Simply use the remote control to enjoy the color spectacle.
PAGE 4
OWNER′S MANUAL REMOTE CONTROL INSTRUCTIONS ON/OFF Cool White Steady Glow Multi Color Steady Glow Color Wheel Next Preset Motion Effect Brightness Up Brightness Down Speed Up Speed Down Previous Preset Motion Effect 1. Remove the insulation tab before use. 2. Tap to turn lights ON or OFF. 3. Tap the Color Wheel to display all lights in one-color steady glow. Sweep around the color wheel to select your desired color. 4. Tap to display all lights in cool white steady glow. 5.