Cut Sheet

Toolin
g
Information
MT-25
b
Hand
Dieless
IDT-6
b
,
IDT-6H
b
,
IDTB-6
b
series
(6-Ton
Hydraulic
Dieless)
IDT-12-N
b
(Dieless)
IVTB-6
b
(Dieless)
Lug/Splice Size Wire Size Color Code Crimps Die Code Crimps Crimps Crimps Die Code Crimps Die Code Crimps Die Code Crimps Crimps
8 8 AWG Blue 1 M,K 2 1 ILD-374 1 ILD-374 1 ILD-374 1
1
6 6 AWG Gray 1 K,K 2 1 1 ILD-346 1 ILD-346 1 ILD-346 1
1
4 4 AWG Green 1 H,H 3 1 1 ILD-375 1 ILD-375 1 ILD-375 1
1
2 2 AWG Pink 2 E,A 3 1 1 ILD-348 1 ILD-348 1 ILD-348 1
2
1 1 AWG Gold 2 E,A 3 1 1 ILD-471 1 ILD-471 1 ILD-471 1
2
1/0 1/0 AWG Tan 2 A,C 3 1 1 ILD-296 1 ILD-296 1 ILD-296 1
2
2/0 2/0 AWG Olive 2 A,B 3 2 1 ILD-297
1
c
ILD-297
1
c
ILD-297
1
c
2
3/0 3/0 AWG Ruby 2 A,A 3 2 1 ILD-467
1
c
ILD-467
1
c
ILD-467
1
c
2
4/0 4/0 AWG White 2 2 1 ILD-298 2 ILD-298 2 ILD-298 2
2
250 250 kcmil Red 2 1 ILD-324 2 ILD-324 2 ILD-324 2
2
300 300 kcmil Blue 2 1 ILD-470 2 ILD-470 2 ILD-470 2
2
350 350 kcmil Brown 2 1 ILD-299 2 ILD-299 2 ILD-299 2
2
400 400 kcmil Green 2 1 ILD-472 4 ILD-472 4 ILD-472 4
2
500 500 kcmil Pink
2
e
1 ILD-300 4 ILD-300 4 ILD-300 4 2
600 600 kcmil Black
2
e
1 ILD-473 4 ILD-473 4 ILD-473 4
700/750 700/750 kcmil Yellow
2
e
1 ILD-936 3 ILD-936 3 ILD-936 3
700/750
g
900 kcmil
Compact Al
Yellow ILD-936 3 ILD-936 3 ILD-936 3
1000 1000 kcmil Brown
ILD-P302
h
3
Additional Information:
1) The ALNS, ALND, ASNS, ASND, ALNB, ASNB, ALNN, ASNN, and ASN connectors are marked with the die numbers and required number of crimps for ILSCO hydraulic tools.
When using other listed tools, consult chart for crimps required. Crimps should be evenly space on connector.
2) Consult manufacturers data for catalog numbers of dies for each tool.
a
Number of crimps shown on chart must be applied to both sides of ASN splice connector's centerline.
e
For ASN splicer connector, apply 4 crimps on both sides of splice connector's centerline.
b
Dieless tools are not color coded and do not require dies.
g
700/750 size lug/splice are additionally rated for use with 900 kcmil compact aluminum wire.
c
For ASN splicer connector, apply 2 crimps on both sides of splice connector's centerline.
h
The die index of ILD-P302 is 302.
d
For ASN splicer connector, apply 3 crimps on both sides of splice connector's centerline.
Connector Installation
1. Select proper connector for the wire size to be used. Series can be used with concentric, compressed or compact aluminum or copper wire.
2. Strip wire insulation using an approved method. Do not nick or ring the wire. Remove any major coating on the wire.
3. Remove surface oxides from the wire with a wire brush.
4. Insert wire all the way into the barrel of the connector.
5. Select the proper die for approved tool. See chart above for approved tools and dies. Compress barrel from tang toward wire, or from inside of ASN connector towards wire.
6. When terminating an aluminum connector to a steel or copper stud, use a belleville or compression type washer in combination with a flat washer. Tighten until the belleville
washer is flat.
FORM 196
Page 1 of 3 Revised 12/19/2017
InformationSheet
SeriesALNS,ALND,ASNS,ASND,ALNB,ASNB,ALNN,ASNN,andASN
a
CompressionConnectorsforAluminumorCopperConductor
ILC-12-N,
ILC-12H-N,
ILCB-12 series
(12-Ton Hydraulic)94285
TM-12U1000,
TR-12U1000,
TB-12U1000 series
(12-Ton Hydraulic)
ILC-15H
(15-Ton)
ILSCO
LR‐29601