User’s Manual CoolCopyD1AL(DVD-Backup) CoolCopyD 3 CoolCopyD 7
Table of Contents . Chapter 1 Introduction .................................................................4 1.1 Overview ....................................................................................4 1.2 Features .....................................................................................4 1.3 Specifications ............................................................................4 Chapter 2 Installation Procedure .............................................5 2.1 Controller only .
4.11.7 Auto Compare ......................................................................20 4.11.8 Auto Prescan .......................................................................21 4.11.9 Eject Disc ............................................................................21 4.11.10 Burn on The Fly ................................................................21 4.11.11 Burn Mode ........................................................................21 4.11.12 Button Sound .......................
Chapter 1 Introduction 1.1 Overview People who want to create multiple copies of their DVDs or CDs usually take a long time to do so. They might not have enough DVD+RW drives or they might be using their computers for some other important tasks. The duplication process noticeably slows down a computer during the burn process. Rather than sit at the computer for hours duplicating discs one at a time, it is much more efficient to use a CoolCopyD DVD/CD duplication system.
Writing mode - Auto Detect (DAO, TAO) Supported DVD-ROM Drive* - EPO, TEAC Supported DVD-RW Drive* - Plextor, TEAC, Lite-On, Asus, SONY Chapter 2 Installation Procedure When you purchase the CoolCopyD DVD Duplicator, the package may be packaged in the following ways: controller only, whole duplicator without writer installed or a complete duplication system. 2.1 Controller only 1.
Hardware Connection with Hard Drive for CoolCopyD3 Coolcopy 3 IDE 3 DVD+/-RW IDE 2 DVD+/-RW IDE 1 DVD+/-RW IDE 0 DVDPower When the system connects with the hard drive, the hard drive must connect on the IDE 0 port with the “Master” setting and the DVD-ROM must set at “Slave”. Hardware Connection without Hard Drive for CoolCopyD3 Coolcopy 3 IDE 3 DVD+/-RW IDE 2 DVD+/-RW IDE 1 DVD+/-RW IDE 0 DVD-ROM Power Copyright©2005 ILY Enterprise, Inc. All rights reserved.
Hardware Connection with Hard Drive for CoolCopyD7 Coolcopy 7 IDE 4 DVD+/- IDE 3 DVD+RW IDE 2 DVD+RW IDE 1 DVD- IDE 8 DVD+RW IDE 7 DVD+RW IDE 6 DVD+RW IDE 5 DVD+RW Power When the system has a hard drive connected, the hard drive must connect on IDE 0 port with “Master” setting and the DVD-ROM must set at “Slave.
Chapter 3 Key Functions and Operating Instruction 1. 2. 3. 4. 5. LCD Display Panel: Display main functions and all messages. Scroll up through menus or functions. Scroll down through menus or functions. Execute the function which you select. Cancel the function which you select. After turning the power on, the CoolCopyD DVD Duplicator will execute a self test for a few seconds. After the self testing procedure runs, the LCD will show: 1. CoolCopyD3: CD Duplicator 1-3 ver: 1.10B 2. Initialize SDRAM....
• • Failed discs will remain in writers. The default setting is to keep failed discs in the writers, but this can be changed. Press the buttons on the drivers to take the failed DVDs. During the duplication process do not press any button because interruption will harm the device. DVDs will be damaged. 2. Without a hard drive installed If you don’t install a 3.5” hard disc, the operation procedures will be as follows: • Place the master disc in the DVD-ROM.
Function 2 Test will simulate the copying process. When the simulation completes, the discs will remain blank. Press ENT button to start the disc simulation. 2. Test If you use DVD rewriteable discs that contain data, the old Data will be quickly erased before simulation. The LCD will show the testing Information as the following screen: . When the process is finished, the LCD will show the message as the following screen: Testing-24X 0% 650.0MB 74:00 2.
4.5 Compare Function 5, Compare, allows you to make a comparison between the source and the target DVDs after copying. Select Function 5. Put the source DVD into DVDROM and the target DVDs into DVD writers. Press ENT to compare. LCD will show the comparison information as the following screen: When comparison completes, the LCD will show as the following screen: Press ENT to see the details of source 1.
If the master disc cannot be read correctly, the LCD will show the following screen: PreScan Fail! 4.7 Disc Info Function 7, Disc Info, shows the basic information of the source DVD. Select Function 7. Place source DVD into DVD-ROM. Press the ENT button to show the disc information. The LCD will show the total sessions and tracks on the master disc.
4.9.1 Load Place the master DVD disc into the DVD-ROM or any one of the DVD writers, the duplicator will detect and analyze the master DVD. Here the function “Load” will allow you to load data from the DVD-ROM or any DVD writer into the current partition of the hard disc. P:A means Partition A. Press ENT to load. The LCD will show the loading information.
Press ENT again and use the arrow button to select the session. The LCD will show the information in the session. Press ENT again and use arrow button to select the track. The LCD will show track information. Session 01 Track 01 - 01 Track 01 DATA 650.0MB 4.9.4 Compare Image Use this function to compare the contents of the source DVD and those of the image file in the partition. First select the function by pressing the arrow.
Use the arrow button to select which partition will be worked. When the partition is set, the LCD will show the following screen: Select Working Partition - A Set Partition to A 4.9.6 Select Src Drive This function allows you to select the DVD-ROM or any DVD writer as the source from which you can load data into a particular partition as an image file. Press ENT and the arrow button to select the source. Then use the arrow button to select the disc as the master source.
Press ENT to finish the disc editing. Use the arrow button to make “Yes” or “No” selection. The LCD will then show the following screen: When copying ends, the LCD will show the following message: The system will ask if you want to continue editing. Use the arrow button to make a “Yes” or “No” selection . If “Yes” is selected, the source disc will be automatically ejected. Insert another disc. Follow the steps to select the track that you want to edit. Then press ENT.
4.10.2 CD to HDD This function lets you select one or more tracks from DVD-ROM and then copies into a certain partition of the HDD. Press ENT to enter the setting. 10-02. Edit Track CD to HDD Edit Follow the LCD to select the track that you want to edit. Here 1/10 means the number one of 10 tracks and 3:25 means the playing time. Select Track: 1/10 03:25 Press ENT button to select the track. After the track is selected, the “+” will appear. Pressing ENT again will cancel the track.
CD-R/RW or move into partition. Selecting “Burn” will start the process. The LCD will show the copying information as such: When burning is finished, the LCD will show the following screen: Selecting Move will move the data from the hard drive template to a certain partition. Select the partition that the data will move into by pressing the arrow.
Press ESC and the arrow to select the function. Press ENT. The system will ask whether you want to close. After this step, the data cannot be written onto the disc. The LCD will show the message as the following screen: When you are finished closing the session, the LCD will show the following message: 10-04. Edit Track Close Session Close all disc’s session? Yes Closing Session Please wait--Closing Complete OK :3 Fail :0 4.11 Setup This function allows you to change default settings.
speed then press ENT. The default is maximum. Other choices are 32X, 16X and 8X. 4.11.4 Auto Start Drive This function automatically tests or copies once you put the blanks discs into the writers. Press the ENT button to enter Auto Start Drive. Use the arrow button to change either the number or the “Off” setting. Then press ENT or ESC to go back to the 11-04 menu. 11-04. Setup Auto Start Drive Auto Start Drive Off 4.11.
4.11.8 Auto Prescan This setting allows you to automatically scan if the source DVD can be read correctly and also tests the reading speed. Press the ENT button to enter Auto Prescan. Use the arrow button to change the “On” or “Off” Setting. Then press ENT or press ESC to return to the 11-08 menu. 11-08. Setup Auto Prescan Auto Prescan Off 4.11.9 Eject Disc The Eject disc setting allows three choices: Eject Good Only, Eject All Disc and Do Not Eject. Press ENT button to enter the following figure: 11-09.
. Press the ENT button to enter Burn Mode. Use the arrow button to change TAO or DAO mode setting. Then press ENT or press ESC to return to the 11-11 menu. 11-11. Setup Burn Mode Burn Mode DAO 4.11.12 Button Sound This setting allows you to control the sound when you press it. Press the ENT button to enter Button Sound. Use the arrow button to change On or Off setting. Then press ENT or press ESC to return to the 11-12 menu. 11-12. Setup Button Sound Button Sound On 4.11.
press ESC to return to the 11-13 menu. Press ENT to see the information and ESC to return to the 11-13 menu. 03 IDE2 Master DVD+RW : PLEXTOR CD-R PX-W2410A 1.01 4.11.14 System Info This function shows the information of the system. Press ENT button to enter the System Info and see the information. Press ESC to exit. The CoolCopyD3 infomation will look like this screen: The CoolCopyD7 information will look like this screen: 11-14. Setup System Info CD Duplicator 1-3 ver: 1.
LCD will show the information as the following screen: Erasing disc 03:24 (Full) When finished, the LCD will show the following message: Full Erase OK:01 Fail:00 4.12 Adv Setup This function allows you to change the system configuration. Changes should be made only when you are fully familiar with the function. To enter the function, please press “ESC” button for 2 seconds. 4.12.
Press the ENT button to enter Format HDD. Use the arrow button to change Yes or No setting. Then press ENT or ESC to go back to the 12-04 menu. All data will be lost, format? Yes If the system does not connect with hard drive, the LCD will show the following message: There is no HDD! 4.12.5 Verify HDD This function verifies whether or not the hard disc or any of its partitions is working well. Press ENT to enter Verify HDD. Use the arrow button to change setting to Disk.
the data and update its firmware automatically. During updating, do not turn off the power of machine because the update will not be finished until machine resets itself. The Update Firmware function updates firmware to the latest version. 2. Unzip the firmware you have and write the file “cdxxx.bin” into the root directory of a blank DVD-R or DVD-RW disc. You have to close the DVD session. If the same DVD disc still has capacity to add more data, it can be used to store newer versions of the firmware.
Press the ENT button to enter Load Default. Use the arrow button to change settings. When “Yes” is selected, the duplicator will return to its factory’s default setting. The LCD message will show that the setting has been changed with the following message: 12-10. Adv Setup Load Default Load Default Config? Yes Load Default OK Chapter 5 Trouble Shooting 1. There’s no display on the LCD or the unit does not operate when you power on.
• Check the DVD-Writer’s maximum writing speed. If you want to copy at 24X writing process or higher, please copy to hard drive first and then to DVD. 7. It cannot boot-up or fails to upgrade firmware. • Contact your dealer to solve the problem. Please note you may be charged for this. • Check whether the BIOS program is correct. Customers tend to download the wrong program or simply write the zipped file to the CD. You should unzip the file before writing it onto the CD.
