Allows setting or changing the password for Setup. 11.9 11.10 Setup Password Reader Speed 11.11 11.13 Compare Speed CHG Bad Master CD Overburn 11.14 Clear Setup 12. IMAGE MANAGER 12.1 Select Image Used to select an Image file as a Source to be copied to the discs. 12.2 Disc -> Image Used to copy a Source Disc to HDD to save as an Image file 12.3 Reader Speed 12.4 Image Info. 12.5 Rename Image 12.6 Delete Image Deletes an image file in HDD.
• The Compare Disc function serves as a bit-by-bit Comparison between Master Reading Source and the copied discs inside the writer trays. This operation ensures that all of the copies are completely identical to the Master • Reading Source. 5. VERIFY 5. Verify 7 discs detected This function will check the master disc and the copied discs’ readability to ensure that all of the copies are readable. 5. Verify 79:45 Loading Disc a.
Burn Speed Audio CD = 40 Press ENT & use , to set the Audio CD burning speed The recommended Audio burn speed is 40x. Burn Speed DVD = 8 Press ENT & use , to set the DVD burning speed Note: DVD burn speed setting is only available on DVD duplicators 8. SELECT SOURCE 8. Select Source Source Drive ==> HDD: ST380021A Source Drive ==> D#1: dvd-rom Set an Optical Drive or Hard Drive Disk as the Master Reading Source. a. Move to 8. Select Source and press ENT. b.
g. Once the Copying Audio Tracks process is complete, copied CD will be displayed. It shows total track on the CD, total time used and total time remain. Track 04 Used Free 20:53 59:25 h. You will need to finalize, indicated on 9.2, before playing back. If you choose NOT to finalize, you can go back to the first step to continue the process. If you choose to finalize, please use “9.2 Close Disc”. Note: Once you finished copy Audio Track, you will NEED to perform “9.
10.3 Full Erase [Utility] 3. Full Erase This operation will erase re-writable discs in the Writer Tray. It is timelier than Quick Erase function. When finished, the writer will automatically eject the trays. Full Erase Disc _O _ _ _ O_o Insert re-writable disc and press ENT Erasing finished and eject discs 10.4 Eject All Discs [Utility] 4. Eject All Disc Ejects disks, including master source disc and discs in writer trays. Press ENT Eject all discs 10.5 Disc Info [Utility] 5.
press ENT Start Update Writing 5% 100% Start Update Pass eject CD New BIOS updated Restart System System re-boot 10.9 Counter This function keeps count of the number of successful and failed disc copied. [Utility] 9. Copy Count a. b. [Copy Count] 1. Show Count press ENT to display the counter CD P0 DVD P0 Shows the number of CD and DVD that passed and failed F0 F0 Turn on the duplicator select 10. Utility, and press ENT, Select 9.
11. SETUP Use this function group to change the manufacturer’s default setting. 11.1 Power On Time [Setup] 1. Power On Time Power On Delay 15 seconds You can set the system warm up time from 5 sec to 255 sec after system power on. a. Select 11. Set Up and press ENT b. Select 1. Power On Time and press ENT c. Press , to increase or decrease the seconds. press ENT press , to set seconds 11.
[Setup] 6. Read Error Skip Skip Read Error ON 11.6 Read Error Skip Choose to stop the duplicating process when error has occurred. press ENT press , to select ON/OFF 11.7 Eject on Start [Setup] 7. Eject On Start Eject On Start Eject All You can choose whether or not to eject the disc when powering up the system. press ENT press , to select Eject All/No Eject/ Eject Target/ Eject Source 11.8 Boot Password [Setup] 8.
There are total of 6 positions for the password. To enable the password set all 6 positions. An empty space is acceptable. Press ESC to cancel the process. The duplicating system will ask for password when 11. Setup is entered. 11.10 Reader Speed [Setup] 10. Reader Speed [Reader Speed] CD = 56 [Reader Speed] DVD = 16 Allow you to set the reading speed of the reader. press ENT press , to change the CD read speed press ENT to select press , to change the DVD read speed press ENT to select 11.
[Image Manager] 2. Disc => Image [Disc = = > A001] 10% 446MB 12.2 Disc => Image This function shows you how to load the master source disc onto the Hard Drive and save it as an image file. a. Place Master Source Disc into any Drive, b. Select 12.2 Disc -> Image and press ENT press ENT 100% [Disc = = > A001] Finished • Note: The source disc can be placed in any Reader or any one of Writer Drive. 12.3 Reader Speed [Image Manager] 3. Reader Speed When you wish to perform this function, 12.
12.6 Delete Image [Image Manager] 6. Delete Image [Delete Image] A001 DVD 4469M This function allows you to delete an image file in HDD. If the file is selected as source file, you will not be able to delete it unless you go back to 12.1 to re-select another image as source. press ENT Select the image file you would like to rename [Delete Image] A003 DVD 4372M Press ENT to confirm A003 DVD 4372M DELETE Complete Press ENT and execute delete 12.7 HDD Info. [Image Manager] 7. HDD Info.
13. LINK SETUP To access this menu use the until you arrived at 13. Link Setup, and then press ENT Note: If no Hard Drive is present in the tower, this function will default to 12. Link Setup. 13.1 Set MyPosition [Link Setup] 1. Set MyPosition [Link Position] == > First This function will allow you to set the position of the tower within the chain. a. Select 13. Link Setup and press ENT b. At 1.Set My Position and press ENT c.
14. About HDD Manager Our duplicator uses rational and dynamic HDD management technology. The traditional method of formatting an HDD requires you to choose the number of partitions designated for DVDs and CDs before formatting your hard drive. The problem is that you might not be able to predict how many DVDs or CDs you will load onto your hard drive. Many incomplete partitions can be created, mainly with new DVD disks constantly coming out, such as the double- layer DVD.
