Flash Duplicator USB/FlashMax/CF/SD/eUSB User’s Manual Version 6.
Table of Contents I. II. Introduction 1.1 Features 2 1.2 Control Panel Overview 3 1.3 Specifica ons 4 Duplication Options Overview 2.1 Copy 5 2.2 Compare 6 2.3 Copy+Compare 6 2.4 Capacity Check 6 2.5 U 6 2.6 ty 2.5.1 Format FAT 6 2.5.2 Measure Speed 7 2.5.3 Quick Erase 7 2.5.4 Full Erase 7 2.5.5 DOD Erase 7 2.5.6 Media Check 7 2.5.7 Media Informa on 8 2.5.8 Device Model 8 2.5.9 System Informa on 8 2.5.10 System Update 8 Setup 9 2.6.
I. Introduction 1. Features Each channel has its own processing control unit and operates independently with dedicated bandwidth of up to 35MB per second. Standalone operation, no PC or software is required to operate. Minimizes possible computer virus infection. Instant power on and off, no warm-up or cool-down required. Easy-to-use One-Touch Copy operation. Available Compare function to verify copy accuracy User-friendly menu options easily accessible through the 4-button control panel.
2.
3. Specifications Model USB, eUSB, SD, MicroSD, CF or CFast Duplicator Target 7, 15, 20, 34, 48, 55, 63, 118 (other configura ons may be available) Operation Standalone (No PC or So ware is required) USB/eUSB: USB 1.1/2.0/3.0 compa ble devices, eUSB (embedded USB) Supported Media Secure Digital: SD / SDHC / Micro SD / MMC / Mini SD CompactFlash: Type 1, II, Micro Drive and CFast Key Features 1. Easy-to-use One-Touch Opera on 2. Support true Asynchronous & Synchronous copy modes 3.
II. Duplication Options Overview 1. Copy: There are two copy modes available: Asynchronous and Synchronous. Please check section 2.6.2 Asynchronous under menu 2.6 Setup to select the correct copy mode. 1.1 Synchronous Copy The duplicator will not start to copy the data from source to target devices until all target devices have been inserted into proper target channels. The copy process will begin and end at the same time. (USB Flash drive was used as the sample device in this manual.) 1.
2. The Green LED above each target channel will begin flashing during the copy process. DO NOT remove any device while the Green LED is flashing. Remove the target devices only after the Green LED stops flashing and replace with a new target device. The copy process starts automatically. 3. You do not have to wait for copy process to complete on all target channels. Simply repeat the process of removing the finished target devices and replacing with a blank one in each individual target channel.
standard FAT format (FAT32 by default). Insert the target flash device into the target channel, scroll to menu option 5.1 Format FAT and press ENT. The duplicator will detect target device capacity automatically and format the device accordingly. Note: buttons to view the real-time status of each You can use individual target device during Format process. To avoid accidental format of source device, the Master Channel will not support Format option. 5.
5.6.1 Verify 100%: Duplicator will read through the entire target device. This option will NOT alter or erase the data format and existing content. 5.6.2 Check USB 100%: To check quality by “0” and “1” reading/writing the flash. Note: Existing content will be erased during the test!!! 5.6.3 Set Range: This option allows you to define the percentage of target device which you wish to have the duplicator to verify. 5.
6 Setup 6.1 Copy Area This option allows you to select the area on the source device to copy onto the target devices. You may select either “Only Data Area” to skip all the unoccupied area on the source device or “Whole Media”. 6.1.1 System and Files The duplicator first analyzes the file format of source device. You may copy only the system and files area to save overall copy time if the file format is FAT16, FAT32, NTFS or Linux (Ext2, Ext3).
6.4 Unknown Format This option allows you to Copy or Skip unknown format. If option Skip is selected here, the unknown format from source will not be copied during copy process. 6.5 Check Before Copy Enable or disable the function to check device before copying. 6.6 Display Mode Two display options: Basic and Expert. 6.7 Start-up Menu Chose one of the following as the default start-up function: Copy, Compare, Copy+Compare, Capacity Check, Utility and Setup. 6.
