b6 06 AC Intelligent Balance Charger Instruction Manual www.imaxrc.
B606 Pro Intelligent digital balance Charger Operating Manual Special features……………………………………………………………………………………….... 01 Performance parameter……………………………………………………………………………… 02 Exterior and accessories……………………………………………………………………………… 02 Key features……………………………………………………………………………………………….. 02 Operating instructions…………………………………………………………………………..…….03 Warning and error messages……………………………………………………………………….11 Safety messages…………………………………………………………………………………………..
Special features: This charger employs an advanced charging calculation and design which allow multilayer error to be compatible.
Performance parameter Input voltage range DC:11~18V AC:100~240V 0.1~6.0A 0.1~2.0A max.80W max.10W max.300mA 0.
Operating instructions: Main menu This shows you the type of charger for 2s, press -check OK. imaxRC B606 Pro Dec. Mode/Esc Dec. User set program, press Mode key down and Esc Press Enter start key into submenu. USER SET PROGRAM Dec. Mode/Esc PROGRAM SELECT Li**BATT Lithium battery program Dec. Mode/Esc PROGRAM SELECT NiMH BATT NiMH battery program Dec. Mode/Esc NiCd battery program PROGRAM SELECT NiCd BATT Dec. Mode/Esc Pb battery program PROGRAM SELECT PB BATT Dec.
Initial parameter set up USER SET PROGRAM Tip: please set up correctly in the “user set” menu before into the job for the first time you use it. Mode/Esc Enter LiPo V.TYPE Lilo V.TYPE 3.7V 3.6V LiFe V.TYPE 3.3V Dec. Inc. LiPo/Lilo/LiFe CHK Time 10 min A0 Dec. Inc. NiMH Sensitivity D.Peak Default A1 Dec. Inc. NiCd Sensitivity D.Peak Default A2 Dec. Inc. A3 USB/Temp Select Temp Cut-off 80C USB/Temp Select USB Enable Dec. Inc. Waste Time CHG DCHG 5min v Dec. A6 Dec. Inc.
Tips: if the voltage of charging battery is lower than 2.5V, V may can not be perceived, this will cause a danger of discharge. You can connect a temperature sensor or use the charger current above 1C to avoid it. There is a 3-pin port on the left side of the unit. It can be used as a temperature sensor port or USB port, if the port is assigned as a temp.
Lithium batteries (Lilo/LiPo/LiFe) program PROGRAM SELECT Li** BATT Mode/Esc Enter/Start Dec. LiPo CHARGE 2.0A 11.1V(3S) Dec. Inc. LiPo BALANCE 2.0A 11.1V(3S) Dec. Inc. LiPo FAST CHG 2.0A 11.1V(3S) Dec. Inc. LiPo 1.0A STORAGE 11.1V(3S) Dec. Inc. LiPo 1.0A DISCHARGE 11.1V(3S) Press Mode key to the screen on the left, then press Enter key to enter into the parameter Start Esc setting menu. You can switch at the same level menu by Dec./Inc. key. Please refer the detailed flow chart on the left.
“Discharge mode” theoretically, Lithium battery do not need to discharge, especially deep-discharge. This feature is to ensure the power wastage of the Lithium battery over 90%, to avoid the overcharge of the individual battery, you should connect the balance plug of the battery to the charger, and the current may not exceed 1C. Start to charge/discharge: after set up the mode menu correctly, press start the process. LiPo 2.0A CHARGE 11.1V(3S) LiPo 2.0A BALANCE 11.1V(3S) LiPo 2.0A FAST CHG 11.
According to press Dec./Inc. key you can inquire the individual voltage of each batteries and final voltage etc. continually as follow (this need to connect the balance plug): Inc. 4.20 0.00 4.20 0.00 4.20 0.00 End Voltage AUTO CHK You can check the individual voltages of each cell in the battery pack while using the individual connection cable to the battery. The final voltage will be reached at the end of process. Dec. Capacity Cut-off ON 5000mAh You can inquire the safety capacity. Dec.
NiMH/NiCd battery program PROGRAM NiMH Enter Press Mode key to the screen on the left, and then press Enter start key to start into the Esc submenu. You can switch at the same level menu to select the mode by Dec./Inc. Key. Please refer the detailed flow chart on the left. When you are willing to alter the parameter value in the program, press Enter start key to make it blink, then change the value with Dec./Inc. key. The value will be stored by pressing Enter start key once.
After check all the mode, to start the process press NiMH CHARGE Aut CUR LINIT 5.0A NiMH 1.0A DISCHARGE 11.5V Mode/Esc Enter >2S Start NiMH 2.0A 7.42V CHG 022:45 00890 1 v NiMH DCHG CHG 2 3 4 5 Enter Start key for more than 2 seconds. The screen displays the present state of process.
discharging Pb battery Pb 4.0A Mode Esc DISCHARGE 12.0V(6P) Enter >2S Start Pb-6 0.4A 12.59V DSC 022:43 00682 Set discharge current on the left and final voltage on the right, the discharge current ranges from 0.1-5.0A and the voltage should be matched with battery being discharged. Start the discharge process by pressing Enter Start key for more than 2 seconds. The screen displays the current state of discharge.
Warning and error messages REVERSE POLARITV The output is connected to a battery with incorrect polarity. CONNECTION BREAK This will be displayed in case of detecting an interruption of the connection between battery and output or voluntarily disconnecting the charge lead during the operation of charge or discharge on output. SHORT ERR There was a short-circuit at output. Please check the charging leads. INPUT VOL ERR The voltage of input power drops below the limit.
BATTERY VOL TAGE CELL LOW VOL The voltage of one of the cell in the Lithium battery pack is too low. Please check the voltage of the cell one by one. BATTERY VOL TAGE CELL HIGH VOL The voltage of one of the cell in the Lithium battery pack is too high. Please check the voltage of the cell one by one. BATTERY VOL ERR CELL CONNECT There is bad connection at the individual connector. Please check the connector and cables carefully. TEMP OVER ERR The internal temperature of the unit goes too high.
Do not attempt the voltage higher than the requirement by manufactures. Ensure the type of the battery and the voltage of the battery pack are selected correctly. Do not use the different types of different types or different capacities synchronously. The standard accessories can only support one battery pack. When you are willing to use multi-packs, please separately purchase the special accessories, never do a disassembly or alteration to the charger.
Warning: imaxRC Co.,LTD • Add: F4 201-205, F518 IDEALAND Baoyuan Road, Baoan, Shenzhen, P.R. C • Tel: +86-755-89830228 • Fax: +86-755-29558361 • Web: www.imaxrc.
b6 06 AC All specifications and figures are subject to change without notice.