X200 AC/DC Manual
New Charger X200AC/DC Released AC Function DC Function Touch Screen Operation 4.3 inch touch screen make the operation more convenient 4.3 inch display screen 4.3 inch TFT display screen, WQVGA(480*272),65 thousand resolution iM·OS V2.15 A whole new OS system for X200AC/DC professional charger with high efficiency USB Port Output 5V 2.1V USB port specially design for iPhone and smartphone charging.
iM·OS System Type Current Cells Mode X200AC/DC support more than 6 type batteries LiPo / Lilon / LiFe / NiMh / NiCd / Pb Input / Output Current Charge 0.1-10A Discharge 0.
iM·OS System LiPo Lipo Battery,Single Nominal Voltage: 3.7V,Charge cutoff voltage 4.2V,Discharge cut-off voltage 3.0V LiIon LiIon Battery,Single Nominal Voltage: 3.6V,Charge cut-off voltage 4.1V,Discharge cut-off voltage 2.5V LiFe LiFe Battery,Single Nominal Voltage: 3.3V,Charge cutoff voltage 3.6ischarge cut-off voltage 20.V NiMH NiMH Battery,Single Nominal Voltage: 1.2V,Charge cut-off voltage 1.5V,Discharge cut-off voltage 1.0V NiCd NiCd Battery,Single Nominal Voltage: 1.2V,Charge cutoff voltage 1.
Balance Lipo balance charge use CC-CV charging way. The charger will balance the battery voltage when charging, this only for LiPo battery. Please connecting the balance port when charging and discharging. Support 2-6 cells. Charge Use CC-CV charging way. On the basis of Users setting current the charger will charge the battery to the cut-off voltage. Warning: The voltage can not balance even connecting the balance port when using LiPo battery. FastCharge FastCharge. Almost same as the Charge Mode.
Checker Measuring Mode. The charger only collect battery primary port and balance port voltage,but can not charge and discharge. Manual Charge This function only for NiMH battery which same as The Charge mode. Cycle This function only for NiMH battery. On the basis of Users setting current for MiNH battery cycle charging and discharging.The Cycle times is 1-6.
X200AC/DC is a professional RC model battery charger,please view the manual before using. If you are a fresh man please read this entire operating manual completely before using. 【Warning: 】The warning of charger operation and disclaimer, Please read and abide by the following terms before operation. 1. This is a sophisticated hobby product. The person who operates the charger should be professional who master professional knowledge about chargers. 2.
Connecting X200AC/DC Please follow the below steps connecting: 1: Please connect the AC power cord with X200AC/DC charger and then plug adapter of power cord into socket. AC input connection DC input connection 2: Connect battery correctly with X200AC/DC. If LiPo battery, pls also connect balance adapter of battery with balance port of X200AC/DC LiPo battery connection NIMH battery connection 【NOTE】 USB support 5V 2.
4: Sarting X200AC/DC startup X200AC/DC to enter the main interface ( Image 1 ). V2.15 Image 1 Showing“Warning and Disclaimer” 2 seconds and will know the copyright and security information ( Image 2 ).
Image 3 【NOTE】 Please read Disclaimer before doing anything. 6: Enter into main interface after accepting( Image 4 ). Start to charge and discharge according to the different battery. Action Bar Information Bar Image 4 【NOTE】 Information bar can not get touched.
Example 1:Choose a set of LiPo battery charging,please follow the below steps: Step 1: Touch Type( Image 5 ) Enter into the “Type interface”, and then Touch :LiPo ( Image 6 ) will Enter into main interface go on the next step.
Step 2: Touch ‘Mode’ icon( Image 7 ) to enter into Mode interface. Please choose battery charge mode ( Image 8 ) and go back to main interface to continue setting. Image 7 Image 8 【Note】 There are six charge/discharge modes in Mode interface( Image 8 ), see iM.OS System function for further details. please set charge/discharge mode according to your requirement. Image 7 is showing Balance charge mode.
Step 3: Touch Cells icon ( Image 9 ) to enter into Cells interface. Please set battery packs by sliding ( Image 10 ). Touch OK to go back to main interface and continue setting. Image 9 Image 10 【Note】Please set according to suitable battery packs.
Step 4: Touch Current icon ( Image 11 ) to enter into Current interface. Please set charge current by sliding ( Image 12 ). Touch OK to go back to main interface and continue setting. Image 11 Image 12 【NOTE】 Set charge current in charge mode and discharge current in discharge mode.
Step 5: If you often use the same battery, please touch Save icon ( Image 13 ) to enter into Save interface. Touch Unused icon to save the data and it will be easy for you to charge next time. ( Image 14 ) Image 13 Image 14 【NOTE】You could use this function after you have set Type/ Mode/Cells and Current correctly.
Step 6: You could load your previous data according to X200AC/ DC’s load function. Touch Load icon ( Image 15 ) to enter into Load interface. Choose the data you want to load ( Image 16 ).
Step 7: Touch Start icon ( Image 17 ) to enter into Start interface. The system will check battery status automatically. If everything is OK, the charger will begin to charge.
【NOTE】The charger will pop-up window when the battery is fully charged. Touch OK to finish charging process ( Image 19 ). Image 19 【NOTE】 The charger will send out an alert and pop-up window if the battery packs’ setting is incorrect (Image 20).
Example 2: If you want to charge a pack of NiMh battery, please execute the operation as follows: Step 1: Touch Type icon ( Image 21 ) to enter into Type interface. Touch NiMh icon to go back to main interface and continue setting ( Image 22 ).
Step 2: Touch Mode icon ( Image 23 ) to enter into Mode interface. Touch Charge icon ( Image 24 ) to go back to main interface and continue setting. Image 23 Image 24 【NOTE】 There are four charge/discharge modes in Mode interface( Image 24 ), see iM.OS System function for further details. please set charge/discharge mode according to your requirement. Image 23 is showing charge mode.
Step 3: Touch Cells icon to enter into Cells interface. Please set NiMh battery packs by sliding ( Image 25). Touch OK to go back to main interface and continue setting ( Image 26). Image 25 Image 26 【NOTE】The battery cannot be charged if each pack of the battery voltage is less than 0.7V, please use the less battery packs to activate charging process. If you need lower voltage during discharging process, please use the less battery packs to discharge.
Step 4: Touch Current icon ( Image 27 ) to enter into Current interface. Please set charge current by sliding ( Image 28 ). Touch OK to go back to main interface and continue setting. Image 27 Image 28 【NOTE】Please set charge current in charge mode and discharge current in discharge mode. As for Save and Load functions, please see Step5 and 6 in Example1 for further details.
Step 5: Touch Start icon ( Image 29 ) to enter into Start interface. The charger will check battery status automatically. If everything is OK, the charger will begin to charge ( Image 30 ).
【NOTE】The charger will pop-up window when the battery is fully charged. Touch OK to finish charging process ( Image 31 ). Image 31 【NOTE】The charger will send out an alert and pop-up window if the battery packs’ setting is incorrect. ( Image 32 ) All Lipo battery packs setting are the same operation.
Example 3: If you want to charge a pack of Pb battery, please execute the operation as follows, Step 1: Touch Type icon ( Image 33 ) to enter into Type interface. Touch Pb icon ( Image 34) to go back to main interface and continue setting. Present Setting Battery Type: Type Cells Mode Current LiPo Mode: Balance Cells: 2Cells 7.4V Current: C 2.0A D 1.
Step 2: Touch Mode icon ( Image 34 ) to enter into Mode interface. Touch Charge icon ( Image 35 ) to go back to main interface and continue setting. Image 34 Image 35 【NOTE】 There are some options in Mode interface ( Image 35 ). Please set according to your requirement. Image 30 is showing charge process.
Step 3: Touch Cells icon ( Image 36 ) to enter into Cells interface. Please set Pb battery packs by sliding ( Image 37 ). Touch OK to go back to main interface and continue setting. Image 36 Image 37 【NOTE】Pleasr set according to suitable battery packs.
Step 4: Touch Current icon ( Image 38 ) to enter into Current interface. Please set charge current by sliding ( Image 39 ). Touch OK to go back to main interface and continue setting. Image 38 Image 39 【NOTE】Set charge current in charge mode and discharge current in discharge mode. As for Save and Load functions, please see Step 5 and 6 in Example1 for further details.
Step 5: Touch Start icon ( Image 40 ) to enter into Start interface. The charger will check battery status automatically. If everything is OK, the charger will begin to charge.
【NOTE】The charger will pop-up window when the battery is fully charged. Touch OK to finish charging process ( Image 42 ). Image 42 【NOTE】The charger will send out an alert and pop-up window if the battery packs’ setting is incorrect. ( Image 43 ) All Lipo battery packs setting are the same operation.
iM·OS SYSTEM ADVANCED APPLICATION iM·OS SYSTEM is brand-new software of charger which was Independently research and develop by iMaxRC. It is the first operation system in the world especially to support touch screen charger,and it’s going to be Industry standard for touch screen charger series. Here we will full display the Advanced application Settings for you. Pls touch Uset ( Image 44 ) to enter into advanced application setting interface.( Image 45 ) Image 44 Cut off Low: 11.
Touch “Cut off Low Input”( Image 46 ), the information bar on left will skip into setting menu( Image 47 ), touch “OK” after setting done, it will turn back to interface ( Image 47 ), then you can go on with setting of other features. Cut off Low: 11.0V Cut off temperaturey: Battery 60℃ Cut off Low Input Cut off temperaturey Cut off Capacity Cut off Time Lixx Check Time Nixx Delta Peak Waste Time Cycle Times Backlight Level Buzzer Language Cut off capacity: 5.
Cut off Low Input Cut off Low Input Range of setting:10-24V. Lowest cut off input voltage, charger will stop charging/discharging when input voltage is lower than setting value. Cut off temperaturey Cut off Temperature Range of setting: 40-80°C. Cut off Temperature, charger will stop charging/discharging when temp of batteries is lower than setting value. Cut off Capacity Cut off Capacity Range of setting: 0.1Ah-10Ah. Safety capacity.
Cycle Time Cycle Times Backlight Level Range of setting: 1-6 times. Backlight Level Range of setting: 1-10, Brightness level. Buzzer Buzzer Range of setting: All sounds open, only touch tone closed, All sounds closed. Language Language Language option. Now provisionally only support English interface. Back Back Turn back to main interface 【IMPORTANT NOTICE】 X200AC/DC charger have 3 parameters to control rotate speed of fan. 1.
Please follow the instruction to operate your X200AC/DC charger, to insure safety of you and charger, and use it easily. Please keep manual within easy reach, to be easy reference for you and other user. 【NOTE】 Procedures, which if not properly followed, can result in potential nullification of any vendor warranties or liabilities.
NEVER use X200AC/DC charger under following operating environment: the environment full of floating dust, smoke from burning or cooking in air. the place have ultrasonic humidifier (for unfiltered tap water) working on. In rare cases, these smoke or particles in air may float into X200AC/DC charger from air-vent. This may lead inner surface of screen appear mist.
without notice.
