Datasheet

3
Product Features
Auto Cross
Auto
Negotiation
Fiber Alert
FIBER
LOS
X
X
LINK
LINK
Link Loss
X
X
LOS
Industrial
Ethernet
Managed
PoE
The following icons highlight features that are found in IMC Networks’ products.
The icons can be found on the top of each product page.
V-LAN
Tagging
T
T
T
Autocross
Autocross allows for automatic detection of the correct MDI / MDIX configuration
on the copper ports (RJ-45), eliminating the need to specify different
cables (crossover or straight-through) and thus eliminating another step in
troubleshooting.
Auto Negotiation
Auto Negotiation allows devices to automatically assign the most efficient line
speed (10/100/1000 Mbps) and mode (Full-Duplex or Half-Duplex) for a particular
network segment between two devices.
Coarse Wave Division Multiplexing
Coarse Wave Division Multiplexing (CWDM) uses uncooled lasers
to combine multiple wavelengths (four, eight or 16; from 1310 nm to
1610 nm) onto a single fiber, using an ITU standard 20 nm spacing between the
wavelengths. Adding wavelengths to the same fiber increases capacity, making
CWDM technology a sound choice for large networks such as Gigabit Ethernet
and Fibre Channel-based Metropolitan Area Networks (MAN).
Config Control
Configuration Control has been implemented on select iMcV-Modules. Its main
function is to assist the end-user by retaining the latest configuration regardless
of how the initial configuration was setup, whether through DIP Switch settings or
the SNMP Management Module’s configuration.
FiberAlert
FiberAlert minimizes the problems associated with the loss of one strand of fiber.
If a strand is unavailable, the device at the receiver end notes the loss of link.
The device will then stop transmitting on the fiber until a signal or link pulse is
received. The result is that the link LED on BOTH sides of the fiber connection
will go out indicating a fault somewhere in the fiber loop.
Industrial Ethernet / Equipment (IE)
IE stands for “Industrial Ethernet” and refers to IMC Networks’ designation for
products that have been designed to operate in a wider temperature range rather
than the typical 0°C to +40°C. IMC Networks’ “IE” products contain additional
features designed for industrial applications, such as multiple powering options
and DIN clips. IE temperature ranges vary, so check the product specifications
for more details.
IE products require third party enclosures for outdoor installations or protection
from moisture, dust and other harsh environmental factors. External protection is
also required for lightning or other serious power surges.
Last Gasp
The Last Gasp feature available on select IMC Networks modules allows for one
final health status message to be sent when remote modules lose power, notifying
network operators that a field visit is necessary.
Link Fault Pass-Through (LFPT)
LFPT (Link Fault Pass-Through) – A feature that allows a segment of a network,
divided by a media converter, to act as if it was one physical piece of media. It
does this by passing a link fault from one side of the media converter to the other.
If a link is lost on one side of the media converter the converter forces a link fault
on the other.
LinkLoss
LinkLoss is a troubleshooting feature that works on either the twisted pair port
(TP/TX) or the fiber port (FO/FX) of devices which have at least one of each port
type. When a fault occurs on one segment of a conversion, LinkLoss detects the
fault and passes this information to the other segment. For example, if a media
converter is not receiving a fiber link, FO/FX LinkLoss disables the transmitter on
the media converter’s twisted pair port. This results in a loss of link on the remote
twisted pair device.
Managed Products
IMC Networks offers several products that support SNMP management,
allowing operators to proactively manage and monitor their devices from a
remote location.
On Board SNMP Management
IMC Networks offers “intelligent” products with on board SNMP management,
allowing operators to proactively manage and monitor the devices without an
additional management controller.
Power Over Ethernet (PoE)
Power Over Ethernet (PoE) is a standards based (IEEE 802.3af) method of
delivering power over twisted-pair network cables (RJ-45) along with data,
thus eliminating the need for a separate run for a power source. There are
two types of PoE devices: the Power Sourcing Equipment (PSE) and the
Powered Device (PD). The PSE supplies power to the PD.
Q-in-Q
Q-in-Q, also known as Extra-Tagging, is an IEEE 802.1Q compliant method
of assigning a VLAN tag to already tagged network traffic. Q-in-Q enables
the transmission of data across multiple VLANs without altering the original
data, providing safer and more secure transmission of data packets over
the network.
RoHS
With environmental protection becoming more important across the globe,
IMC Networks has taken a leadership position by designing products that are
free of lead, cadmium and 6 other toxic materials. This makes the products
of IMC Networks compliant with the Restriction of Hazardous Substances in
Electrical and Electronic Equipment Directive (RoHS), passed into law by
the European Union. All part numbers starting with “8” are RoHS compliant.
Single-Strand Fiber
Single-Strand Fiber technology allows two wavelengths to share one fiber
strand. Full-Duplex data travels on different wavelengths (1310 nm and
1550 nm) which effectively doubles the capacity of installed fiber. Since
single-strand fiber products use optics that transmit and receive on two
different wavelengths, single-strand fiber products must be deployed in pairs.
The pair can consist of two IMC or third-party products that conform to the
same IMC standard.
Traffic Prioritization
Traffic Prioritization (IEEE 802.1p) provides advanced packet management
of network traffic by assigning a priority ID to each packet, insuring that high-
priority traffic (such as VoIP) receives the network resources and bandwidth
necessary for high Quality of Service (QoS).
Unified Management Agent (UMA)
The Unified Management Agent (UMA) is a proprietary system developed
by IMC Networks to utilize a separate management domain on the network
in order to keep management and other data separate. UMA is an IP-less
management method which simplifies management of supported devices by
reducing the number of IP addresses.
VLAN Tagging
VLAN Tagging (IEEE 802.1Q) involves assigning identification information
to data packets on a network to insure that data is efficiently and correctly
routed between devices. The VLAN tag includes an EtherType, priority bits
and a VLAN ID that allows each packet to remain secure and intact while
being routed across multiple networks.
Administration and Maintenance
IEEE 802.3ah OAM includes features associated with Discovery, Link
Monitoring, Events, Remote Loopback and Performance Monitoring and
Reporting. IMC Networks’ implementation of 802.3ah supports both Active
and Passive operational modes on all ports and software upgrades are Free
to IMC Networks clients.
UMA
1 IP
Address
SNMP
802.1p
Last Gasp
ON
BOARD
Q-in-Q
T
TT
1310
1310
1550
1550
Single
Strand
Fiber
CWDM
LFPT
X
X
X
Config
Control
802.3ah