User Manual

ManualsBrandsImpact ManualsLightingDigital Monolight 300Ws

VSD Series Monolight

INSTRUCTIONS

www.impactstudiolighting.com

impact

Page 16

(back cover)

Page 1

(front cover)

10M 25M 50M 75 M 100M 10Y 25Y 50Y 75Y 100Y

To see all of our lighting equipment,

please visit our Web site.

Impact provides a limited warranty that this product is free from defects in

materials and workmanship to the original purchaser under normal use for a

period of one (1) year from the original purchase date. Impact’s responsibility

with respect to this limited warranty shall be limited solely to repair or

replacement, at its option, of any product which fails during normal consumer

use. This warranty does not extend to damage or failure which results from

misuse, neglect, accident, alteration, abuse, improper installation or

maintenance. To obtain a replacement during the time of this warranty,

please return the defective item with proof of purchase along with an RMA

number to the place of purchase. This warranty gives you specic legal

rights, and you may also have other rights which vary from state to state.

Summary of content (16 pages)

PAGE 1
VSD Series Monolight INSTRUCTIONS
PAGE 2
Thank you for purchasing an Impact VSD Series Monolight. This device is proof that highly-functional monolights can be affordable. The VSD Series Monolight provides enough stored power to light a portrait or small still-life setup and offers features found on monolights costing twice as much. We expect that you will get many years of trouble-free service and enjoyment from your Impact VSD Monolight. Please read these operating instructions and safety precautions carefully before operating this equipment.
PAGE 3
Preparing Your Monolight for Use Contents of carton Carefully remove the monolight from the box. You should have the following: • • • • 110-120V monolight with protective cap and flashtube installed 100W modeling lamp (60W with VSD-160 model) 7˝ grid reflector • sync cable power cable • user manual Mount on a stand (1) Select a stand or support system of suitable weight and dimensions to ensure stable operation of the unit.
PAGE 4
T A B C G F K D E L H I J P M N O Q R S 4
PAGE 5
Operating Instructions Legend A – Digital Power Readout B – Modeling Light Control – Up C – Modeling Light Control – Down D – Flash Power Control – Up E – Flash Power Control – Down F – Modeling Lamp Control G – Modeling Lamp LED – Free H – Modeling Lamp LED – Proportional I – Recycle Tone Control J – Recycle Tone LED K – Photo Slave Control L – Photo Slave LED M – Test Fire Button N – Full Recycle Status LED O – Mini-plug Sync Jack P – On/Off Switch Q – Power Socket R – Fuse Holder S – Umbrella Holder T –
PAGE 6
Flash Settings Flash Output The flash power output is variable over a four f/stop range (five f/stops) from full power to 1/16 power in 1/10 f/stop increments. The power is displayed on the LCD screen. Minimum setting is 2.0 and the maximum is 6.0. Pressing the up and down touch-pad buttons under the LCD changes the value by 0.1 f-stop (a total of 40 values). If the current value is 5.6 and you want to reduce the power by one stop, set the power to 4.6. Setting Power 6.0 Full Power 5.0 1/2 Power 4.
PAGE 7
Modeling Lamp Settings There are three modes for the modeling light: Proportional, Full, and Off. You can choose a mode by pressing the modeling lamp control button, which is to the left of the FULL and PROP LEDs. Each time you press, the mode will change. Proportional Mode During normal use, most photographers will use a monolight in “proportional” mode. The modeling light intensity will increase or decrease in response to changes in the flash power.
PAGE 8
Triggering the Flash TEST Button There are three ways to trigger your flash, but the simplest is to press the TEST button. This is useful when you need to discharge the power built up in the flash unit, for example just before replacing the flashtube (more on that later). Sync Connection The sync jack on the VSD Monolight may be used for direct connection to a camera set to ‘X’ synchronization.
PAGE 9
Audible Beep Settings To Turn the Audible Beep Off A beep will sound when the flash has recycled and is ready to flash again. You can turn this audible beep off by pressing the AUDIO button with the musical eighth notes. The small LED next to this button will not be lit when the audible beep has been turned off. If you have turned the audible beep off, you can still confirm that the flash has recycled and is ready to fire by looking at the small LED next to the TEST button.
PAGE 10
Use of Umbrellas and Softboxes Umbrellas An umbrella with a shaft diameter of up to 8mm can be secured in the umbrella holder. Firmly press the umbrella shaft through the holder. The locking knob is located beneath the holder. Do not overtighten to avoid damaging the shaft of the umbrella. The monolight can be pointed up or down by loosening the release lever. Adjust to your preferred angle and then tighten the lever back down.
PAGE 11
Changing the Flashtube Discharge the Flash Unit The charge in the flash unit must be discharged before removing the flashtube. Make sure the flash unit is on. Push the TEST button on the rear panel of the flash. The unit will flash, discharging the power. Immediately turn off the power switch on the rear panel. Unplug the power cord from the power source. It is advisable to wait at least 30 minutes before touching or removing the flashtube. Remove Old Flashtube First, remove the reflector.
PAGE 12
Changing the Fuse A 6A fuse is mounted in the rear panel and protects the circuitry of the flash unit. Turn off the unit and disconnect the power supply before changing the fuse. Never replace with a fuse of a different type or rating. A spare 6A fuse is fitted within the fuse holder. Use a small screwdriver to release the fuse cover. Remove the old fuse, place the new fuse in the slot, then replace the fuse holder.
PAGE 13
Best Practices As with any flash unit, the useful life of the flashtube and the unit as a whole depends on the way it is used. Avoiding excessive heat is the key to long life. • The fast recycling feature of the VSD Series allows a rapid sequence of high-power flashes. However, this feature should be used sparingly, since continuous rapid flashing can cause overheating and subsequent damage to the flashtube and possibly the internal electronics.
PAGE 14
Safety and Maintenance Notes Safety Notes • Do not use your flash in an environment where moisture may come in contact with the unit. • A fire hazard exists if flammable materials are placed in close proximity to the flash tube or the modeling lamp. Do not use your flash in an environment where flammable vapors are present. • Do not restrict the ventilation holes when the flash is in use. • Always switch off the power and disconnect the power cord before changing the fuse, modeling lamp, or flashtube.
PAGE 15
Specifications Model Flash Output VSD-160 VSD-300 160 Watt/sec 300 Watt/sec Flash Variations Guide Number1 1/16 – Full GN40 GN55 Power Supply 110V AC / 60 Hz Recycle Time 1-2 seconds @ min. power Modeling Lamp Color Temperature Flash Triggering Trigger Voltage Sync Range Dimensions (mm) Weight 60 Watts 100 Watts 5600 ±200°K sync cord, slave cell, test button 4.3V DC ≥10m 11.6˝ x 8.4˝ x 6.1˝ (with reflector) 11.6˝ x 8.4˝ x 5.2˝ (with protective cap) 3.
PAGE 16
One-Year Limited Warranty This IMPACT product is warranted to the original purchaser to be free from defects in materials and workmanship under normal consumer use for a period of one (1) year from the original purchase date or thirty (30) days after replacement, whichever occurs later.