NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice Hardware Identifier COMPETITOR BENCH CB-430 Assembly Instruction Parts List Warranty Ordering Parts Model CB-430 Retain This Manual for Reference 07-03-03 OWNER'S MANUAL IMPEX FITNESS PRODUCTS 14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746 Tel: (800) 999-8899 Fax: (626) 961-9966 www.impex-fitness.com info@impex-fitness.
TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................…. IMPORTANT SAFETY NOTICES..................................................................…. HARDWARE IDENTIFIER.....…....................................................................…. ASSEMBLY INSTRUCTIONS........................................................................…. EXPLODED DIAGRAM………………………………………………………………. PARTS LIST.......................................................
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person at a time should use the machine. 3.
HARDWARE IDENTIFIER 3
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches NOTE: It is strongly recommended two or more people assembling this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Attach the Front Stabilizer (#22) to the Main Frame (#4). Secure it with two M10 x 3 1/8” Carriage Bolts (#54), one 4 ¾” x 1 5/8” Bracket (#26), two ∅ ¾” Washers (#64), and two M10 Aircraft Nuts (#63). B.) Connect the two Rear Stabilizers (#5) with the Lat Bar Base (#6).
STEP 2 (See Diagram 2) A.) Slide the Sliding Weight Post (#11) onto the Lat Bar Frame (#1). Insert the Lat Bar Frame into the opening on the Lat Bar Base (#6). B.) Attach the Cross Brace (#7) to the Lat Bar Base. Align the holes on the Lat Bar Frame, Lat Bar Base, and Cross Brace. Secure them with three M10 x 2 ¾” Carriage Bolts (#56), one 1 5/8” x 2” Bracket (#38), one 6 ¾” x 2” Bracket (#39), three ∅ ¾” Washers (#64), and three M10 Aircraft Nuts (#63). Do not tighten the nuts and bolts yet. C.
STEP 3 (See Diagram 3) A.) Attach the bottom of Right Upright Beam (#3) to the Rear Stabilizer (#5). Attach the Right Upright Beam to the Cross Brace (#7). B.) Secure the Right Upright Beam to the Rear Stabilizer with two M10 x 3 1/8” Carriage Bolts (#54), ∅ ¾” Washers (#64), and M10 Aircraft Nuts (#63). C.) Secure the Right Upright Beam to the Cross Brace with two M10 x 2 ¾” Carriage Bolts (#56), one 4 ¾” x 2” Bracket (#27), two ∅ ¾” Washers (#64), and two M10 Aircraft Nuts (#63). D.
STEP 4 (See Diagram 4) A.) Attach the Cable (#17) to the opening on the top of the Lat Bar Frame (#1). Make sure the ball stopper of the Cable is underneath the Frame. B.) Attach a Pulley (#29) to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#57), two Ø 5/8” Pulley Bushings (#43), two ∅ ¾” Washers (#64), and one M10 Aircraft Nut (#63). C.) Draw the Cable to the bracket on the top of Lat Bar Frame. Attach a Pulley to the bracket.
STEP 5 (See Diagram 5) A.) Attach the Seat Support (#15) to the bracket on the Main Frame. Secure it with one M10 x 2 ½” Allen Bolt (#57), two ∅ ¾” Washers (#64), and one M10 Aircraft Nut (#63). B.) Attach the holes on the Backrest Supports (#16) to the pivot on the Seat Support (#15). Attach the Backrest Board (#19) to the Backrest Supports (#16). Secure it with four M6 x 1 3/8” Hex Bolts (#58) and ∅ ½” Washers (#66). C.) Place the Seat (#18) onto the Seat Support (#15).
STEP 6 (See Diagram 6) A.) Attach the Leg Developer (#8) to the Main Frame. Secure it with M10 x 3” Allen Bolt (#59), two ∅ ¾” Washers (#64), and one M10 Aircraft Nut (#63). B.) Insert one Foam Tube (#25) halfway through the hole on the Main Base Frame. Insert two Foam Tubes halfway through the holes on the Leg Developer. C.) Push six Foam Rolls (#31) onto the Foam Tubes from both ends. D.) Attach the Curl Bar Handle Frame (#13) to the Leg Developer. Secure it with a Lshaped Pin (#40).
10
PARTS LIST KEY NO.
IMPEX INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX.
