NOTE: Please read all instructions carefully before using this product Table of Contents ROCKING HAMMOCK GD-600 Safety Notice Hardware Pack Assembly Instruction Parts List Warranty Ordering Parts Model GD-600 Retain This Manual for Reference 11-24-09 OWNER'S MANUAL IMPEX® INC. 14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746 Tel: (800) 999-8899 Fax: (626) 961-9966 www.impex-fitness.com info@impex-fitness.
TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................... IMPORTANT SAFETY NOTICES..................................................................... HARDWARE IDENTIFIER……......…............................................................... ASSEMBLY INSTRUCTIONS........................................................................... OPERATION………………………………………………………………………… EXPLODED DIAGRAM......................................................
IMPORTANT SAFETY NOTICE Please read the entire manual before assembling or operating the equipment. In particular, note the following safety precautions to reduce the likelihood of injury. 1. Children must be supervised at all times and never left unattended with the unit. 2. Make sure the surfaces are free of objects that may cause tipping over. 3. Place the equipment on level ground, not less than 6 ft (1.
WARNING LABEL PLACEMENT The Warning Label shown here has been placed on the Stabilizer Frame. If the label is missing or illegible, please call customer service at 1-800-999-8899 for replacement. Apply the label in location shown.
HARDWARE IDENTIFIER Part# Description #2 Cap Washer (Qty 16) #3 Cover Cap (Qty 16) #24 M8 x 5/8” Allen Bolt (Qty 16) Identifier Tools: #5 Allen Wrench (Qty 1) 4
ASSEMBLY INSTRUCTION Tool Required for Assembling the Machine: #5 Allen Wrench NOTE: It is strongly recommended that two or more people assemble this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Do not tighten Bolts until instructed to do so. B.) Attach the two Stabilizer Tubes (#11) to the two Hammock Base Frames (#4). C.) Secure each end of the Stabilizer Tube to the Hammock Base Frame with two M8 x 5/8” Allen Bolt (#24) and two Cap Washers (#2). D.
Step 2 (See Diagram 2) A.) Do not tighten Bolts until instructed to do so. B.) Insert a Hammock Body Support Tube (#12) through the sleeve next to the pillow on Hammock Body (#15). NOTE: The pillow needs to be on top of the Hammock Body. C.) Insert the Right Long Support (#6) into the right opening on the Hammock Base Frame (#4). D.) Attach right end of the Hammock Body Support Tube to the Right Long Support Frame. Attach the left end to the Left Long Support (#5). E.
Step 3 (See Diagram 3) A.) Insert the Right Short Support (#8) into right opening on the Hammock Base Frame (#4). B.) Insert the Hammock Body Support Tube (#12) through the other open sleeve on the Hammock Body. C.) Attach the right end of the Hammock Body Support Tube to the Right Short Support. Attach the other end to the Left Short Support (#7). D.) Insert the Left Short Support into the left opening on the Hammock Base Frame. E.) Securely tighten all Bolts in previous step and this step.
Step 4 (See Diagram 4) A.) Insert the Support Rod (#21) and Sun Shade Rod (#20) through the sleeve on the Sun Shade (#14). B.) Insert each end of the Support Rod into the Left and Right Rod Holder (#18) on Sun Shade Support Frame.
Step 5 (See Diagram 5) A.) Insert the Sun Shade Support Frame (#13) into the Long Support Cover Caps (#17).
Step 6 (See Diagram 6) A.) Cover all M8 x 5/8” Allen Bolts (#24) and Cap Washers (#2) with sixteen Cover Caps (#3).
OPERATION 1. 2. 3. 4. Place the Rocking Hammock on flat surface. Lay in the middle of the Hammock Body only, and place head on the pillow. Gently sway body and the Hammock will start rocking. To remove the Sun Shade just simply pull out the Support Rod from the Rod holder, and then pull out the Sun Shade Support Frame.
EXPLODED DIAGRAM 12
Parts list KEY NO.
® IMPEX INC. LIMITED WARRANTY ® IMPEX INC ("IMPEX ") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of 2 YEARS from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX.
