NOTE: Please read all instructions carefully before using this product Table of Contents LOUNGE ROCKER GD-700 Safety Notice Hardware Pack Assembly Instruction Parts List Warranty Ordering Parts Model GD-700 Retain This Manual for Reference 100126 OWNER'S MANUAL IMPEX® INC. 14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746 Tel: (800) 999-8899 Fax: (626) 961-9966 www.impex-fitness.com info@impex-fitness.
TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................... IMPORTANT SAFETY NOTICES..................................................................... HARDWARE IDENTIFIER……......…............................................................... ASSEMBLY INSTRUCTIONS........................................................................... SET UP LOUNGE ROCKER POSITION…………………………………………. EXPLODED DIAGRAM.............................................
IMPORTANT SAFETY NOTICE Please read the entire manual before assembling or operating the equipment. In particular, note the following safety precautions to reduce the likelihood of injury. 1. Children must be supervised at all times and never left unattended with the unit. 2. Make sure the surfaces are free of objects that may cause tipping over. 3. Place the equipment on level ground, not less than 6 ft (1.
WARNING LABEL PLACEMENT The Warning Label shown here has been placed on the Stabilizer Frame. If the label is missing or illegible, please call customer service at 1-800-999-8899 for replacement. Apply the label in location shown.
HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
ASSEMBLY INSTRUCTION Tool Required for Assembling the Machine: Allen Wrench and Crossing Wrenches NOTE: It is strongly recommended that two or more people assemble this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Do not fasten Bolts until instructed to do so. B.) Slide the Front Cross Tube (#21) onto the front of the Right and Left Base (#8 & #22). Secure each end of the Front Cross Tube with one M10 x 2” Allen Bolt (#6) and one Ø 1” x Ø 3/8” Curved Washer (#7). C.
Step 2 (See Diagram 2) A.) Do not fasten Bolt until all six M8 x 2” Allen Bolts (#2) are installed. B.) Place the Lounge Bed (#1) onto the six upright posts on the Right and Left Base (#8 & #22). Align the holes on the Lounge Bed Frame (#4) to the holes on the six upright posts. C.) Secure each hole on the Lounge Bed to each upright post with one M8 x 2” Allen Bolt (#2) and one Ø 7/8” x 5/16” Curved Washer (#3). D.) Securely fasten all Bolts installed in Procedure C.
Step 3 (See Diagram 3) A.) Securely fasten all six Allen Bolts (#6) installed in Step-1.
Step 4 (See Diagram 4) A.) Attach the Upright Stand (#25) to the bracket on the Rear Cross Tube (#28). Secure it with one M8 x 5/8” Hex Bolt (#16), one Ø 5/8” Washer (#18), and one M8 Aircraft Nut (#19). Note: Do not over tighten the Nut and Bolt. The Upright Stand needs to be able to move smoothly. B.) Turn the Upright Stand stands on floor or horizontally under Middle Cross Tube (#29) to set up various Lounge Rocker position.
Step 5 (See Diagram 5) A.) Attach the Foot Rest Tube (#11) to the Foot Actuator (#12). Secure it with one M8 x 2” Allen Bolt (#2) and one Ø 7/8” x 5/16” Curved Washer (#3). B.) Slide the Foot Rest Support onto the Rocker Tube (#17). Use the Pop Pin (#13) to lock the Foot Actuator at selected hole to obtain the desired footrest position.
Step 6 (See Diagram 6) A.) Attach the Rocker Tube (#17) to the bracket on Front Cross Tube (#21). Secure it with one M8 x 1 5/8” Hex Bolt (#16), one Ø 5/8” Washer (#18), and one M8 Aircraft Nut (#19). Note: Do not over tighten the Nut and Bolt. The Rocker Tube needs to be able to move smoothly.
Set up Lounge Rocker position 1. Neutral Position Turn the Upright Stand (#25) horizontally under the Middle Cross Tube (#29). Tuck the Rocker Tube (#17) under the Lounge Bed so the Rocker Tube could lean on the floor. 2. Rocking Position Turn the Upright Stand (#25) horizontally under the Middle Cross Tube (#29). Pull the Rocker Tube (#17) forward. Step both feet on the Foot Rest Tube (#11); gently push the Foot Rest tube, and the Lounge will start rocking. The Lounge Rocker can rock up to approx.
Storage Lift up the front of Lounge vertically for space saving storage.
13
Parts list KEY NO.
® IMPEX INC. LIMITED WARRANTY ® IMPEX INC ("IMPEX ") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of 2 YEARS from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX.
