NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice Hardware Identifier Assembly Instruction Parts List MARCY® CLASSIC INVERSION TABLE IVT-450 Warranty Ordering Parts Model IVT-50 Retain This Manual for Reference 05-27-09 OWNER'S MANUAL IMPEX® INC. 14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746 Tel: (800) 999-8899 Fax: (626) 961-9966 www.impex-fitness.com info@impex-fitness.
TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................…. IMPORTANT SAFETY NOTICES..................................................................…. HARDWARE IDENTIFIER.....…....................................................................…. ASSEMBLY INSTRUCTIONS........................................................................…. EXPLODED DIAGRAM………………………………………………………………. PARTS LIST.......................................................
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person at a time should use the machine. 3.
WARNING LABEL REPLACEMENT The Warning Label shown here has been placed on the Rear Support Frame. If the label is missing or illegible, please call customer service at 1-800-999-8899 for replacement. Apply the label in location shown.
HARDWARE IDENTIFIER NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
ASSEMBLY INSTRUCTION Tools Required for Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended that two or more people assemble this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Do not tighten the Nuts and Bolts until instructed to do so. B.) Attach Front Support Frame (#1) to Rear Support Frame (#2). Secure them together with one M10 x 1” Allen Bolt (#34), two Ø ¾” Washers (#45), and one M10 aircraft Nut (#43) on each end. C.
DIAGRAM 1 6
STEP 2 (See Diagram 2) A.) Attach the two Pivot Brackets (#12) to the Backrest Frame (#7) from each side. B.) Secure each Pivot Bracket to the Backrest Frame with two M8 x ¾” Allen Bolts (#38) and two Ø ¾” Washers (#45). C.) Lift the Backrest Frame and insert the two Pivot Brackets into the open slot on Rear Support Frame (#2). Make sure the groves on the Pivot are attached on the slots completely and the Pivots can swing smoothly. D.
STEP 3 (See Diagram 3) A.) Attach the Left Handle (#8) to Front Support Frame (#1). Secure it with one M8 x ¾” Allen Bolt (#35), one Ø 5/8” Washer (#46), and one M8 Aircraft Nut (#43). B.) Attach the Left Handle to the Rear Support Frame (#2). Secure it with one M8 x 1 ¾” Allen Bolt (#36), one Ø 5/8” Washer (#46), and one M8 Aircraft Nut (#43). C.) Repeat Procedures A & B to install the Right Handle (#9).
STEP 4 (See Diagram 4) A.) Pull up the Foot Adjustment Lock Pin (#23). Insert the Foot Lock Frame (#13) into the Adjustment Fame (#11). Push down the Pin to securely lock the Foot Lock Frame in position. B.) Insert the Foot Support (#6) into the bottom of Adjustment Frame. Secure it with one M8 x 1 5/8” Allen Bolt (#40), one Ø 5/8” Washer (#46), and one M8 Aircraft Nut (#43). C.) Insert the Foam Tube halfway through the hole on Adjustment Frame. Push two Foam Rolls (#17) onto the Tube from both ends. D.
STEP 5 (See Diagram 5) A.) Pull out the Backrest Adjustment Lock Pin (#22). Insert the Adjustment Frame (#11) into the opening on the vertical frame on the back of Backrest Frame (#7). Push back the Pin into the selected hole on Adjustment Frame. B.) Insert the Ring Lock Pin (#21) through the hole on the vertical frame and hole on Adjustment Frame to securely lock the Adjustment Frame. C.) Attach hook on Inversion Adjustment Belt (#15) to Front Support Frame (#1) and to the vertical frame on Backrest Frame.
EXPLODED DIAGRAM 11
PARTS LIST KEY NO.
® IMPEX INC. LIMITED WARRANTY ® IMPEX Inc. ("IMPEX ") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX.
