NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice Hardware Pack Assembly Instruction MARCY® CLASSIC MID-SIZE BENCH MCB 880-MG Parts List Resistance Chart Warranty Ordering Parts Model MCB-880MG Retain This Manual for Reference 07-16-08 OWNER'S MANUAL IMPEX® INC. 14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746 Tel: (800) 999-8899 Fax: (626) 961-9966 www.impex-fitness.com info@impex-fitness.
TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................... IMPORTANT SAFETY NOTICES..................................................................... HARDWARE PACK……….....…....................................................................... ASSEMBLY INSTRUCTIONS...............................................................….......... EXPLODED DIAGRAM……………………………………………………………. PARTS LIST…………………………………………………………….……….……. WARRANTY................
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person at a time should use the same station. 3.
WARNING LABEL REPLACEMENT The warning labels shown here have been placed on the Rear Stabilizer, Base Frame, and Lat Bar Frame. If the labels are missing or illegible, please call customer service at 1-800-888-8899 for replacements. Apply the labels in location shown.
HARDWARE PACK 4
HARDWARE PACK 5
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended two or people assembling this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Attach the two Base Frames (#65) together on a flat surface. Attach the Left & Right Upright Beams (#67 & #68) onto the two Base Frames. Secure each Upright with two M10 x 3 ¾” Carriage Bolts (#46), Ø ¾” Washers (#39), and M10 Aircraft Nuts (#51).
STEP 2 (See Diagram 2) A.) Attach the Lat Bar Frame Support (#66) onto the joint of the two Base Frames (#65). Align the holes and secure them together with two M10 x 3 ¾” Carriage Bolts (#46), Ø ¾” Washers (#39) and M10 Aircraft Nuts (#51). B.) Attach the Lat Bar Frame Support (#66) to the bracket on the Cross Brace (#69). Attach the Rear Diagonal Support Frame (#77) to the back of Lat Bar Frame.
STEP 3 (See Diagram 3) A.) Attach the 57” Cable (#74) to a Pulley (#57). Attach the Pulley to the top opening on the Lat Bar Frame (#70). Secure it with a M10 x 2 3/8” Allen Bolt (#48), two Pulley Bushings (#59), and one M10 Aircraft Nut (#51). Make sure the ball stopper on the Cable is underneath the opening. B.) Draw the Cable over the Pulley to the open bracket on the rear of the Lat Bar Frame.
STEP 4 (See Diagram 4) A.) Attach the Main Frame (#1) onto the Front & Rear Stabilizers (#2 & #6). Secure each end with two M10 x ¾” Allen Bolts (#32) and Ø ¾” Washers (#39).
STEP 5 (See Diagram 5) A.) Attach the two Backrest Supports (#3) to the pivot on the Main Frame (#1). Secure it with one M12 x 5 ¾” Allen Bolt (#31), two Ø1” Washers (#38), and one M12 Aircraft Nut (#36). Do not over tighten the nut and bolt. Make sure the Backrest Supports are able to swivel. B.) Attach the Backrest Incline Support (#4) in between the two Backrest Supports. Secure it with one M12 x 5 ¾” Allen Bolt (#31), two Ø 1” Washers (#38), and one M12 Aircraft Nut (#36).
STEP 6 (See Diagram 6) A.) Attach the Leg Developer (#5) to the open bracket on the Main Frame (#1). Secure it with one Axle (#42), two M10 x 5/8” Allen Bolts (#30), and two Ø ¾” Washers (#39). Do not over tighten the bolts. Make sure the Leg Developer is able to swivel. B.) Insert the U-shaped Pin (#10) into the tube in front of the Main Frame. Secure it with one Spring (#29), Ø ½” Washer (#28), and M6 x 5/8” Philips Screw (#41). C.
STEP 7 (See Diagram 7) A.) Attach the Arm Curl Pad (#13) to the Arm Curl Stand (#7). Secure it with two M8 x ¾” Allen Bolts (#33) and Ø 5/8” Washers (#40). B.) Insert the Arm Curl Stand into the front opening on the Main Frame. Use a Lock Knob (#16) to secure the Stand at desired height. C.) The Leg Developer can be locked when doing sit up exercises. Simply pull the U-shaped Pin (#10) out and drop into the hole on the Leg Developer. Remove the Pin when doing Leg Developer exercises. D.
EXPLODED DIAGRAM 13
14
PARTS LIST KEY NO.
® IMPEX INC. LIMITED WARRANTY ® IMPEX Inc. ("IMPEX ") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX.
