NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice Hardware Identifier MARCY CLASSIC MCB-346 COMBO BENCH Assembly Instruction Exploded Diagram Parts List Warranty Ordering Parts Model MCB-346 Retain This Manual for Reference 06-29-06 OWNER'S MANUAL IMPEX® INC. 14777 Don Julian Rd., City of Industry, CA 91746 Tel: (800) 999-8899 Fax (626) 961-9966 www.impex-fitness.com info@impex-fitness.
TABLE OF CONTENTS BEFORE YOU BEGIN...............................................................................................1 IMPORTANT SAFETY NOTICE................................................................................2 HARDWARE PACK……............................................................................................4 ASSEMBLY INSTRUCTIONS....................................................................................5 EXPLODED DIAGRAM............................................
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person at a time should use the machine. 3.
WARNING LABEL REPLACEMENT The Warning Label shown here has been placed on the Cross Brace. If the label is missing or illegible, please call customer service at 1-800-999-8899 for replacement. Apply the label in location shown.
HARDWARE PACK 4
ASSEMBLY INSTRUCTION Tools required assembling the machine: Two Adjustable Wrenches and Allen Wrenches STEP 1 (SEE Diagram 1) A.) Connect the two Rear Upright Beams (#1) by a Cross Brace (#15) in the Mid-span. Secure them with two M10 x 2 3/8” Hex Bolts (#2), four ∅ ¾” Washers (#3), one Bracket (#7), and two M10 Aircraft Nuts (#4) on each end of the Cross Brace. B.) Insert the Backrest Adjustment Bar (#10) through a selected hole to obtain desired incline of Backrest. C.
STEP 2 (SEE DIAGRAM 2) A.) Connect the Front Stabilizer (#42) to the Main Seat Support (#52) and secure them with two M10 x ¾” Hex Bolts (#46), four ∅ ¾” Washers (#3), and two M10 Aircraft Nuts (#4). DO NOT tighten the nuts and bolts yet. B.) Connect the Main Seat Support (#52) to the open bracket on the Cross Brace (#15). Secure it with two M10 x 2 3/8” Bolts (#2), four ∅ ¾” Washers (#3), and two M10 Aircraft Nuts (#4). DO NOT tighten the nuts and bolts yet. C.
STEP 3 (SEE DIAGRAM 3) A.) Attach the Leg Developer (#38) to the bracket on the Front Stabilizer (#42). Secure it with a Socket axle (#44) and Socket Screw (#45). Do not over tighten the Screw. Make sure the Leg Developer is able to swivel. B.) Insert two Foam Roll Tubes (#39) halfway through the holes on the Leg Developer. Push four Foam Rolls (#37) onto the Tubes from both sided. C.) Attach a Spring Clip (#34) onto the weight post on the Leg Developer. D.
STEP 4 (SEE DIAGRAM 4) A.) Attach the Backrest Supports (#16) onto both ends of the Pivot on the Main Seat Support (#52). Place the other end rest against the Backrest Adjustment Bar (#10). B.) Place the Backrest Board (#18) onto the Backrest Supports. Secure it with four M6 x 1 3/8” Hex Bolts (#50) and ∅ ½” Washers (#51). C.) Place the Seat (#19) onto the bracket on the Main Seat Support (#52). Align the holes and secure the Seat with four M6 x 1 3/8” Hex Bolts (#50) and ∅ ½” Washers (#51). D.
STEP 5 (SEE Diagram 5) A.) Attach the ball end of the Cable to the Pulley (#28). Place the Pulley in the open slot on the Lat Bar Frame (#31). Secure it with one M10 x 2 1/8” Hex Bolt (#32), two Bushings (#29), two ∅ ¾” Washers (#3), and one M10 Aircraft Nut (#4). B.) Slide the Weight Holder (#33) onto the Lat Bar Frame from the bottom. Connect the Cable to the Holder with a Hook (#26). Attach a Spring Clip (#34) onto the post on the Weight Holder. D.
10
PARTS LIST KEY NO.
® IMPEX INC. LIMITED WARRANTY ® IMPEX Inc. ("IMPEX ") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX.