NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice Hardware Identifier MARCY CLASSIC MCB-347 COMBO BENCH Assembly Instruction Exploded Diagram Parts List Warranty Ordering Parts Model MCB-347 Retain This Manual for Reference 06-25-08 OWNER'S MANUAL IMPEX® INC. 14777 Don Julian Rd., City of Industry, CA 91746 Tel: (800) 999-8899 Fax (626) 961-9966 www.impex-fitness.com info@impex-fitness.
TABLE OF CONTENTS BEFORE YOU BEGIN............................................................................................... 1 IMPORTANT SAFETY NOTICE................................................................................ 2 HARDWARE PACK……............................................................................................ 4 ASSEMBLY INSTRUCTIONS.................................................................................... 5 EXPLODED DIAGRAM........................................
Toll-Free Customer Service Number 1-800-999-8899 Mon. - Fri. 9 a.m. - 5 p.m. PST www.impex-fitness.com info@impex-fitness.com 1 IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times.
1. Lubricate moving parts with WD-40 or light oil periodically. 2. Inspect and tighten all parts before using the machine. 3. The machine can be cleaned using a damp cloth and mild non-abrasive detergent. DO NOT use solvents. WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC.
WARNING LABEL REPLACEMENT The Warning Label shown here has been placed on the Cross Brace. If the label is missing or illegible, please call customer service at 1-800-999-8899 for replacement. Apply the label in location shown.
HARDWARE PACK 4
ASSEMBLY INSTRUCTION Tools required assembling the machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended two or more people assembling this machine to avoid possible injury. STEP 1 (SEE DIAGRAM 1) A.) Connect the two Rear Upright Beams (#1) by a Cross Brace (#2) in the Mid-span. Secure each end of Cross Brace with two M10 x 3 1/8” Hex Bolts (#40), four ∅ ¾” Washers (#48), one Bracket (#17), and two M10 Aircraft Nuts (#51). B.
STEP 2 (SEE DIAGRAM 2) A.) Attach the Front Stabilizer (#5) to the Main Seat Support (#3). Secure it with two M10 x ¾” Hex Bolts (#43), four ∅ ¾” Washers (#48), and two M10 Aircraft Nuts (#51). DO NOT tighten the nuts and bolts yet. B.) Attach the Main Seat Support (#3) to the Cross Brace (#2). Secure it with two M10 x 2 1/8” Hex Bolts (#41), one Bracket (#17), four ∅ ¾” Washers (#48), and two M10 Aircraft Nuts (#51). C.) Attach one end of Diagonal Support (#4) to the Main Seat Support.
STEP 3 (SEE DIAGRAM 3) A.) Attach the Leg Developer (#6) to the bracket on the Front Stabilizer (#5). Secure it with one M10 x 2 ¾” Hex Bolt (#42), two Ø ¾” Washers (#48), and one M10 Aircraft Nut (#51). Do not over tighten the Nut and Bolt. Make sure the Leg Developer is able to swivel. B.) Insert two Foam Tubes (#8) halfway through the holes on the Leg Developer. Push four Foam Rolls (#39) onto the Tubes from both ends. C.) Attach the Arm Curl Handle (#7) to the open bracket on the Leg Developer.
STEP 4 (SEE DIAGRAM 4) A.) Attach the side holes on the Backrest Supports (#14) to the Pivot on the Main Seat Support (#3). Place the other end rest against the Backrest Adjustment Bar (#9). B.) Attach the Backrest Board (#19) onto the Backrest Supports. Secure it with four M6 x 1 ½” Hex Bolts (#47) and ∅ ½” Washers (#50). C.) Place the Seat Pad (#18) onto the bracket on the Main Seat Support. Secure it with four M6 x 1 ¼” Hex Bolts (#46) and ∅ ½” Washers (#50). D.
8 STEP 5 (SEE Diagram 5) A.) Attach the ball end of the Cable (#38) to the Pulley (#36). Place the Pulley in the open slot on the Lat Bar Frame (#15). Secure the Pulley with one M10 x 2 1/8” Hex Bolt (#41), two Bushings (#37), and one M10 Aircraft Nut (#51). B.) Slide the Weight Holder (#13) onto the Lat Bar Frame from the bottom. Connect the Cable to the Holder with a Hook (#22). Attach a Spring Clip (#21) onto the post on the Weight Holder. C.) Connect the Lat Bar (#16) to the Cable with a Hook (#22).
9
10
PARTS LIST KEY NO.
® IMPEX INC. LIMITED WARRANTY ® IMPEX Inc. ("IMPEX ") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX.
