NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice Hardware Identifier Assembly Instruction Parts List MARCY® CLASSIC WEIGHT BENCH MCB-379 Warranty Ordering Parts Model MCB-379 Retain This Manual for Reference 05-26-09 OWNER'S MANUAL IMPEX® INC. 2801 S. Towne Ave, Pomona, CA 91766 Tel: (800) 999-8899 Fax: (626) 961-9966 www.impex-fitness.com info@impex-fitness.
TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................…. IMPORTANT SAFETY NOTICES..................................................................…. HARDWARE IDENTIFIER.....…....................................................................…. ASSEMBLY INSTRUCTIONS........................................................................…. EXPLODED DIAGRAM………………………………………………………………. PARTS LIST.......................................................
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person at a time should use the machine. 3.
WARNING LABEL REPLACEMENT The Warning Label shown here has been placed on the Cross Brace. If the label is missing or illegible, please call customer service at 1-800-999-8899 for replacement. Apply the label in location shown.
HARDWARE IDENTIFIER NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
ASSEMBLY INSTRUCTION Tools Required for Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches NOTE: It is strongly recommended that two or more people assemble this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Connect the Right & Left Upright Beam (#1 & #2) with a Cross Brace (#4) in the Midspan. Secure them with two M10 x 3 1/8” Carriage Bolts (#29), one 2 3/8” x 4 ¾” Bracket (#13), two ¾” Washers (#38), and two M10 Aircraft Nuts (#39) on each end of the Cross Brace. B.
STEP 2 (See Diagram 2) A.) Do not tighten Nuts and Bolts until instructed to do so. B.) Attach the Main Seat Support (#3) to the Cross Brace (#4). Secure them together with two M10 x 2 ½” Carriage Bolts (#30), one 1 ¾” x 4 3/8” Bracket (#12), two Ø ¾” Washers (#38), and two M10 Aircraft Nuts (#39). C.) Attach the Main Seat Support to the Front Post (#5). Secure it with three M8 x 5/8” Allen Bolts (#32) and three Ø 5/8” Washers (#37). D.) Attach the Diagonal Support (#8) to Front Post.
STEP 3 (See Diagram 3) A.) Attach the Leg Developer (#7) to the open bracket on Front Post (#5). Secure it with one M8 x 2 5/8” Allen Bolt (#31), two Ø 5/8” Washers (#37), and one M8 Aircraft Nut (#40). B.) Attach the pivot on Arm Curl Handle to the open bracket on Leg Developer. Use the Lshaped Lock Pin (#23) to lock it in position.
STEP 4 (See Diagram 4) A.) Attach the Backrest Supports (#10) onto both ends of the pivot on the Main Seat Support (#3). Place the other end rest against the Backrest Adjustment Bar (#9). B.) Place the Backrest Board (#15) onto the Backrest Supports. Secure it with four M6 x 1 ½” Hex Bolts (#34) and four Ø ½” Washers (#36). C.) Place the Seat Pad (#16) onto the Main Seat Support. Secure it with four M6 x 1 3/8” Hex Bolts (#35) and four Ø ½” Washers (#36). D.
STEP 5 (See Diagram 5) A.) Insert two Foam Tubes (#11) halfway through the holes on Leg Developer (#7). B.) Push four Foam Rolls (#18) onto the Tubes from both ends. C.) Remove the Arm Curl Handle (#14) when doing Leg Developer exercises.
10
PARTS LIST KEY NO.
® IMPEX INC. LIMITED WARRANTY ® IMPEX Inc. ("IMPEX ") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX.
