NOTE: Please read all instructions carefully before using this product Table of Contents MARCY DIAMOND ELITE Safety Notice SMITH MACHINE MD-4100 Hardware Identifier Assembly Instruction Parts List Warranty Ordering Parts Model MD-4100 Retain This Manual for Reference 09-25-07 OWNER'S MANUAL IMPEX® INC. 14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746 Tel: (800) 999-8899 Fax: (626) 961-9966 www.impex-fitness.com info@impex-fitness.
TABLE OF CONTENTS BEFORE YOU BEGIN..................................................................................... IMPORTANT SAFETY NOTICES.................................................................... HARDWARE PACK….......…...........................................……………………… ASSEMBLY INSTRUCTIONS..........................................……………………… EXPLODED DIAGRAM…………………………………………………………….. PARTS LIST………..……………………………………………………………….. WARRANTY...........................................................
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person at a time should use the machine. 3.
WARNING LABEL PLACEMENT The warning labels shown here have been placed on the Cross Brace and Upper Frame. If the labels are missing or illegible, please call customer service at 1-800-888-8899 for replacements. Apply the labels in the location shown.
HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches NOTE: It is strongly recommended two or more people assembling this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Do not tighten all nuts and bolts until instructed to do so. B.) Attach one Base Frame (#1) to the Left Rear Vertical Frame (#5). Attach the Cross Brace (#8) to the back of the Left Rear Vertical Frame.
STEP 2 (See Diagram 2) A.) Insert one Guide Rod (#24) into the hole on the Left Base Frame (#1). Secure the bottom with one M10 x 1” Allen Bolt (#59). B.) Slide the Left Lower Safety Stop Frame (#20) onto the Guide Rod from the top. Slide the Safety Stop Frame (#19) onto the Guide Rod from the top. C.) Attach top of the Guide Rod to the tube on the Left Rear Vertical Frame (#5). Secure it with a M8x1¾” Allen Bolt (#65), two Ø 5/8” Washers (#72), and one M8 Aircraft Nut (#74). D.
STEP 3 (See Diagram 3) A.) Attach the Rear Vertical Frame Base (#9) to the Cross Brace (#8). Attach the Rear Vertical Frame (#10) to the Cross Brace. Align the holes and secure them together with two M10 x 2 3/8” Carriage Bolts (#67), Ø ¾” Washers (#73), and M10 Aircraft Nuts (#75). B.) Slide the Sliding Pulley Bracket (#14) onto the Rear Vertical Frame. Use a Lock Knob (#52) to secure it in position. C.) Attach the Weight Glide Post (#13) to the bracket on the Rear Vertical Frame Base (#9).
STEP 4 (See Diagram 4) A.) Attach the Upper Frame (#11) to the top of the Rear Vertical Frame (#10). Attach two Cover Brackets (#12) to the Upper Frame and the Rear Vertical Frame. Secure them together with four M10 x 2 3/8” Carriage Bolts (#67), Ø ¾” Washers (#73), and M10 Aircraft Nuts (#75). B.) Attach the two Cover Brackets to the Weight Glide Post (#13). Secure them with one M10 x 2 ½” Carriage Bolt (#70), Ø ¾” Washer (#73) and M10 Aircraft Nut (#75). C.
CABLE LOOP DIAGRAM 11
STEP 5 (See Diagram 5 & Cable Loop Diagram) A.) Attach the 135” Upper Cable (#54) to the front opening on the Upper Frame (#11). Attach a Pulley (#42) to the opening. Secure it with one M10 x 2 1/8” Allen Bolt (#60), two Ø 1 1/8” x 3/8” Pulley Bushings (#58), and one M10 Aircraft Nut (#75). Make sure the ball stopper on the Cable is underneath the Frame. B.) Draw the Cable over the Pulley along the Upper Frame to the opening between the two Cover Brackets (#12). Attach a Pulley to the opening.
DIAGRAM 5 13
STEP 6 (See Diagram 6 & Cable Loop Diagram) A.) Attach the “Ball” on the 245” High-Low Cable (#55) in between two Small Pulleys (#43). Attach the two Small Pulleys to the Sliding Pulley Bracket (#14). Secure each Small Pulley to the Bracket with one M10 x 1 ¾” Allen Bolt (#62), two Ø ¾” Washers (#73), and one M10 Aircraft Nut (#75). B.) Draw the Cable upward to the top opening on the Rear Vertical Frame (#10). Attach a Pulley (#42) to the opening.
DIAGRAM 6 15
STEP 7 (See Diagram 7) A.) NOTE: Help of another person is strongly recommended for this step. Place the Lifting Sleeve (#22) in between the two Safety Stop Frames (#19). Align the holes and insert the Weight Bar (#27) all the way through. Center the bar and secure it with two M8 x 3/8” Allen Bolts (#71) on each side. B.) Turn the safety catch hook forward on the Lifting Sleeve to secure its position on the selected “knuckle” on the Left & Right Front Vertical Frames (#2 & #3).
EXPLODED DIAGRAM 17
PARTS LIST KEY NO.
® IMPEX INC. LIMITED WARRANTY ® IMPEX Inc. ("IMPEX ") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX.
