NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice Hardware Pack MARCY DIAMOND WEIGHT BENCH MD-844 Assembly Instruction Exploded Diagram Parts List Warranty Ordering Parts Model MD-844 Retain This Manual for Reference 05/08/09 OWNER'S MANUAL IMPEX® INC. 2801 S. Towne, Pomona, CA 91766 Tel: (800) 999-8899 Fax (626) 961-9966 www.impex-fitness.com info@impex-fitness.
TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................... IMPORTANT SAFETY NOTICE....................................................................... HARDWARE PACK………............................................................................... ASSEMBLY INSTRUCTIONS........................................................................... EXPLODED DIAGRAM....................................................................................
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person at a time should use the machine. 3.
WARNING LABEL REPLACEMENT The Warning Labels shown here have been placed on the Base Frame. If the label i missing or illegible, please call customer service at 1-800-999-8899 for replacement.
HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
ASSEMBLY INSTRUCTION Tools Required For Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended for two or more people to assemble this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Attach one Rear Base Frame (#3) to the Base Frame (#2). Attach an Upright Beam (#1) onto the Base Frame and Rear Base Frame.
DIAGRAM 1 7
STEP 2 (See Diagram 2) A.) Attach the Main Seat Support (#6) to the Base Frame (#2). Secure it with two M10 x 3 ½” Carriage Bolts (#43), one 4 ¾” x 2” Bracket (#15), two Ø ¾” Washers (#53), and two M10 Aircraft Nuts (#57). Do not tighten the Nuts and Bolts yet. B.) Attach the Front Post (#10) to the Main Seat Support. Secure it with two M10 x 2 ¾” Allen Bolts (#47), one 4”x 2” Bracket (#16), one Ø ¾” Washer (#53), and one M10 Aircraft Nut (#57). C.) Securely tighten all Nuts and Bolts.
STEP 3 (See Diagram 3) A.) Attach the holes on the end of the two Backrest Supports (#8) to the pivot on the Main Seat Support (#6). Secure the two Backrest Supports to the pivot with one M12 x 6 1/8” Hex Bolt (#42), two Ø 1” Washers (#52), and one M12 Aircraft Nut (#56). Do not over tighten the Nuts and Bolts. Make sure the Backrest Supports are able to swivel. B.) Attach the two L-shaped Seat Brackets (#20) to the Main Seat Support. Align the holes.
STEP 4 (See Diagram 4) A.) Attach two Ø ¾” Leg Developer Bushings (#27) to the Leg Developer (#11). Attach the Leg Developer to the Front Post (#10). Secure it with one M10 x 3 1/8” Allen Bolt (#46), two Ø ¾” Washers (#53), and one M10 Aircraft Nut (#57). Do not over tighten the Nut and Bolt. Make sure the Leg Developer is able to swivel. B.) Insert three Foam Tubes (#13) halfway through the holes on the Leg Developer and Front Post. Push six Foam Rolls (#33) onto the Tubes from both ends.
STEP 5 (SEE DIAGRAM 5) A.) Attach the Arm Curl Pad (#23) to the Arm Curl Bracket (#19). Secure it with two M8 x 5/8” Allen Bolts (#50) and two Ø 5/8” Washers (#54). B.) Attach the Arm Curl Bracket to the bracket on the Arm Curl Stand (#9). Insert the M10 x 3 1’2” Allen Bolt (#45) through the open track on the Arm Curl Stand and the holes on the Arm Curl Bracket then secure the Bolt with two Ø ¾” Washers (#53), and one M10 Aircraft Nut (#57). Do not over tighten the Nut and Bolt.
12
PARTS LIST KEY NO.
IMPEX INC. LIMITED WARRANTY ® IMPEX Inc. ("IMPEX ") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX.