NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice Hardware Pack MARCY PLATINUM MP 1105 HOME GYM Assembly Instruction Parts List Resistance Chart Warranty Ordering Parts Model MP-1105 Retain This Manual for Reference 07-12-06 OWNER'S MANUAL IMPEX® INC. 14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746 Tel: (800) 999-8899 Fax: (626) 961-9966 www.impex-fitness.com info@impex-fitness.
TABLE OF CONTENTS BEFORE YOU BEGIN....................................................................................……….. 1 IMPORTANT SAFETY NOTICES...................................................................……….. 2 HARDWARE IDENTIFIER.....….....................................................................……….. 4 ASSEMBLY INSTRUCTIONS.........................................................................……….. 7 PARTS LIST…………………………………………………………………………………..
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person at a time should use the machine. 3.
WARNING LABEL REPLACEMENT The warning labels shown here have been placed on the Rear Stabilizer and Upper Frame. If the labels are missing or illegible, please call customer service at 1-800-888-8899 for replacements. Apply the labels in the location shown.
HARDWARE PACK 4
HARDWARE PACK 5
HARDWARE PACK 6
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended two or more people assembling this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Do NOT tighten the nuts and bolts until instructed to do so. B.) Slide two Ø2 ½” Round Rubber Bumpers (#43) onto the Guide Rods (#7). Insert the two Guide Rods into the holes on the Rear Stabilizer (#8).
DIAGRAM 1 8
STEP 2 (See Diagram 2) A.) Slide 9 Weight Plates (#37) onto the Guide Rods (#7). Make sure the grooves on the Plates all face up and to the same direction. Insert a Selector Rod (#21) into the center hole on the Plates. Slide the Selector Stem (#36) onto the Guide Rods. B.) Attach the Upper Frame (#6) onto the Guide Rods (#7). Secure it with two M10 x 1” Allen Bolts (#72) and Ø ¾” Washers (#79). C.) Place the Upper Frame (#6) onto the Vertical Frame (#2).
STEP 3 (See Diagram 3) A.) Place the Seat (#55) onto the Seat Support (#10). Secure it with two M8 x 1 5/8” Allen Bolts (#67) and Ø 5/8” Washers (#80). B.) Insert the Seat Support into the opening on the Main Base Frame (#1). Use a Lock Knob (#53) to secure the Seat Support at desired height. C.) Attach two ∅1” x ½” Bushings (#34) to the Leg Developer (#9). Attach the Leg Developer to the bracket on the Main Base Frame.
STEP 4 (See Diagram 4) A.) Attach the Front Press Base (#3) to the Upper Frame (#6). Secure it with one Axle (#24), two Ø ¾” Washers (#79), and two M10 Aircraft Nuts (#82). Do not over tighten the Nuts. B.) Insert the axle on the Right Butterfly (#4) through the holes on the Front Press Base (#3) from the bottom. Slide a Lock Ring (#60) onto the axle. Align the holes and secure it with one M6 x 1 ¼” Allen Bolt (#75) and M6 Aircraft Nut (#83). Repeat the same step to install the Left Butterfly (#5). C.
CABLE LOOP DIAGRAM 12
STEP 5 (See Diagram 5 & Cable Loop Diagram) A.) Attach the 144” Upper Cable (#57) to the front opening on the Upper Frame (#6). NOTE: The Ball Stopper on the Cable needs to be underneath the Frame. B.) Attach a Pulley (#41) to the opening. Secure it with one M10 x 3 7/8” Allen Bolt (#77), two Ø 7/8” Pulley Bushings (#35), two Ø ¾” Washers (#79), and one M10 Aircraft Nut (#82). C.) Draw the Cable towards the back of the machine to another opening on the Upper Frame. Repeat Step B above to install a Pulley.
DIAGRAM 5 14
STEP 6 (See Diagram 6 & Cable Loop Diagram) A.) Attach one end of the 108” Butterfly Cable (#58) to the hook on the Right Butterfly (#4). Draw the Cable towards the right open Swivel Pulley Bracket (#17). B.) Attach a Pulley (#41) to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#64), two ∅ ¾” Washers (#79), and one M10 Aircraft Nut (#82). C.) Draw the Cable over the Pulley then pull downward. Attach the Cable to an Angled Double Floating Pulley Bracket (#15). Install another Pulley.
STEP 7 (See Diagram 7 & Cable Loop Diagram) A.) Attach the 170” Lower Cable (#59) to the opening on the bottom of the Leg Developer (#9). B.) Attach a Pulley (#41) to the opening. Secure it with one M10 x 3” Allen Bolt (#76), two Pulley Bushings (#40), two Ø ¾” Washers (#79), and one M10 Aircraft Nut (#82). C.) Draw the Cable underneath the Pulley towards the back of the machine to the opening on the Front Base Frame (#19).
DIAGRAM 7 17
PARTS LIST KEY NO.
19
® IMPEX INC. LIMITED WARRANTY ® IMPEX Inc. ("IMPEX ") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX.
