NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice Hardware Identifier MARCY PLATINUM SMITH CAGE MP-3105 Assembly Instruction Parts List Warranty Ordering Parts Model MP-3105 Retain This Manual for Reference 12-27-06 OWNER'S MANUAL IMPEX® 14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746 Tel: (800) 999-8899 Fax: (626) 961-9966 www.impex-fitness.com info@impex-fitness.
TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................... IMPORTANT SAFETY NOTICES..................................................................... HARDWARE PACK….......…..........................................………………………. ASSEMBLY INSTRUCTIONS...........................................……………………. EXPLODED DIAGRAM…………………………………………………………….. PARTS LIST………..……………………………………………………………….. WARRANTY........................................................
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person at a time should use the machine. 3.
WARNING LABEL REPLACEMENT The warning labels shown here have been placed on the Cross Brace, Rear Stabilizer, and Upper Frame. If the labels are missing or illegible, please call customer service at 1-800-888-8899 for replacements. Apply the labels in location shown.
HARDEWARE PACK 4
HARDEWARE PACK 5
HARDEWARE PACK 6
HARDEWARE PACK 7
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended two or more people assembling this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) NOTE: Do not tighten the Nuts and Bolts until instructed to do so. B.) Attach one Diagonal Support (#3) to the Right Cross Brace (#15).
DIAGRAM 1 9
STEP 2 (See Diagram 2) A.) Attach the Left Vertical Beam (#1) to the left Diagonal Support (#3). Secure it with two M10 x 2 ¾” Carriage Bolts (#83), one 4 3/8” x 2 ¾” Bent Bracket (#25), two Ø ¾” Washers (#87), and two M10 Aircraft Nuts (#89). B.) Attach one Guide Rod (#5) onto the left Diagonal Support. Secure it with one M10 x 1” Allen Bolt (#72) and Ø ¾” Washer (#87) from the bottom. C.) Slide a Ø 2 ½” x 1” Rubber Bumper (#65) and the Left Safety Stop Frame (#7) onto the Guide Rod from the top. D.
STEP 3 (See Diagram 3) A.) Place the Weight Glide Post (#12) onto the Weight Glide Post Base (#11). Secure it with four M10 x ¾” Carriage Bolts (#79), Ø ¾” Washers (#87) and M10 Aircraft Nuts (#89). B.) Slide the Sliding Weight Post (#22) onto the Weight Glide Post. C.) Attach the Upper Frame (#13) onto the Rear Vertical Beam (#10). Secure it with two M10 x 3 1/8” Carriage Bolts (#84), one 3 ½” x 1 5/8” Bent Bracket (#28), two Ø ¾” Washers (#87), and two M10 Aircraft Nuts (#89). D.
DIAGRAM 3 12
STEP 4 (See Diagram 4) A.) Attach the Butterfly Base (#17) to the front of Rear Vertical Beam (#10). Attach the Butterfly Pulley Bracket (#18) to the back of Rear Vertical Beam. Align the holes and secure them with two M10 x 2” Carriage Bolts (#80), Ø ¾” Washers (#87), and M10 Aircraft Nuts (#89). B.) Insert the Axle on the Left Butterfly (#19) into the Butterfly Base from the bottom. Secure it with one Lock Ring (#54), Ø 1 ½” Washer (#53), M6 x 1 ¼” Allen Bolt (#69), and M6 Aircraft Nut (#88). C.
CABLE LOOP DIAGRAM 14
STEP 5 (See Diagram 5 & Cable Loop Diagram) A.) Attach a 123” Cable (#37) to the front opening on the Upper Frame (#13). Attach a Pulley (#44) to the opening. Secure it with one M10 x 2 3/8” Allen Bolt (#75), two Ø 1 1/8” x 3/8” Pulley Bushings (#42), and one M10 Aircraft Nut (#89). Make sure the ball stopper on the Cable is underneath the Upper Frame. B.) Draw the Cable over the Pulley along the Upper Frame to the opening on the rear of Upper Frame. Attach a Pulley to the opening.
DIAGRAM 5 16
STEP 6 (See Diagram 6 & Cable Loop Diagram) A.) Attach one end of the 79” Butterfly Cable (#36) to the clip on the Left Butterfly (#19). Draw the Cable to the left Butterfly Pulley Bracket (#18). B.) Attach a Pulley (#44) to the Bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#73), two ∅ ¾” Washers (#87), and one M10 Aircraft Nut (#89). C.) Draw the Cable around the Pulley then downward. Attach the Cable to a Single Floating Pulley Bracket (#24). Install a Pulley to the Bracket.
STEP 7 (See Diagram 7 & Cable Loop Diagram) A.) Attach one 123” Cable (#37) to the lower opening on the Rear Vertical Beam (#10). Attach a Small Pulley (#45) to the opening. Secure it with a M10 x 2 ¾” Allen Bolt (#76), two Ø 1” x 5/8” Pulley Bushings (#41), and one M10 Aircraft Nut (#89). B.) Draw the Cable underneath the Pulley to the open bracket on the Weight Glide Post Base (#11). Attach a Pulley to the bracket.
STEP 8 (See Diagram 8) A.) Note: Help of another person is strongly recommended for this step. Place the Weight Lifting Sleeve (#6) in between the two Safety Stop Frames (#7 & #8). Align the holes and insert the Weight Bar (#9) into the Left Safety Stop Frame through the Weight Lifting Sleeve to the other end of Right Safety Stop Frame. Turn the safety hooks on the Weight Lifting Sleeve to secure its position on the selected slot of the Vertical Beams (#1 & #2).
STEP 9 (See Diagram 9) A.) Attach the Main Seat Support (#92) to the Rear Stabilizer (#93). Secure it with two M10 x 3 ½” Allen Bolts (#114), one 2 ¾” x 2” Bent Bracket (#27) and two Ø ¾” Washers (#87). B.) Attach the Front Post (#94) to the Main Seat Support. Secure it with two M10 x 2 ¾” Carriage Bolts (#83), one 4 3/8” x 2 ¾” Bent Bracket (#25), two Ø ¾” Washers (#87), and two M10 Aircraft Nuts (#89). C.
STEP-10 (See Diagram 10) A.) Attach the Seat Bracket (#95) to the pivot on the Main Seat Support (#92). B.) Attach the two Backrest Supports (#97) to the Seat Bracket (#95) and align the holes. Secure them with a M12 x 8 ½” Allen Bolt (#113), two Ø 1” Washers (#111), and one M12 Aircraft Nut (#112). Use the T-shaped Lock Pin on the Main Seat Support to lock the Seat Bracket at desired incline. C.) Attach the Backrest Incline Support (#96) in between the two Backrest Supports (#97).
STEP-11 (See Diagram 11) A.) Place the Seat Pad (#103) onto the Seat Bracket (#95). Secure it with four M8 x 1 5/8” Allen Bolts (#98) and Ø 5/8” Washers (#86). B.) Attach the Bench Backrest Board (#104) to the Backrest Supports (#97). Secure it with four M8 x 1 5/8” Allen Bolts (#98) and Ø5/8” Washers (#86).
SMITH MACHINE EXPLODED DIAGRAM 23
24
PARTS LIST KEY NO.
® IMPEX LIMITED WARRANTY ® IMPEX warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX Customer Service Department at 1-800-999-8899.
