NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice Hardware Identifier MARCY PLATINUM MP-PWR 10.0 Assembly Instruction Parts List Warranty Ordering Parts Model MP-PWR10.0 Retain This Manual for Reference 04-08-05 OWNER'S MANUAL IMPEX INC. 14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746 Tel: (800) 999-8899 Fax: (626) 961-9966 www.impex-fitness.com info@impex-fitness.
TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................... 1 IMPORTANT SAFETY NOTICES..................................................................... 2 HARDWARE PACK……….....…....................................................................... 3 ASSEMBLY INSTRUCTIONS........................................................................... 6 EXPLODED DIAGRAM.........................................................................……….
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person at a time should use the machine. 3.
HARDWARE PACK 3
HARDWARE PACK 4
HARDWARE PACK 5
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches NOTE: It is strongly recommended this machine be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Attach the Main Frame (#27) to the Bench Front & Rear Stabilizers (#28 & 29). Secure each end with two M10 x ¾” Allen Bolts (#81) and ∅ ¾” Washers (#69). B.) Attach four Stabilizer End Caps (#58) onto the Stabilizers.
STEP 2 (See Diagram 2) A.) Attach the two side-holes on bottom of Backrest Supports (#30) to the pivot on the Main Frame (#27). Secure it with one M12 x 5 ¾” Allen Bolt (#75), two Ø 1” Washers (#68), and one M12 Aircraft Nut (#71). B.) Align the pivot on top of Backrest Incline Support (#31) to the middle side-holes in between the Backrest Supports. Secure it with one M12 x 5 ¾” Allen Bolt (#75), two Ø 1” Washers (#68), and one M12 Aircraft Nut (#71). C.
STEP 3 (See Diagram 3) A.) Attach the Leg Developer (#33) to the open bracket on the Main Frame (#27). Secure it with one M10 x 3 1/8” Allen Bolt (#76), two Ø ¾” Washers (#69), and one M10 Aircraft Nut (#72). Do not over tighten the bolt and nut, make sure Leg Developer is able to swivel. B.) Insert the U-shaped Pin (#39) into the open tube on the Main Frame (#27). Secure it with one M6 x ½” Philips Screw (#43), Ø ½” Washer (#41), and Spring (#42).
STEP 4 (See Diagram 4) A.) Attach the Arm Curl Pad (#37) to the Arm Curl Stand (#32). Secure it with two M8 x ¾” Allen Bolts (#84) and two ∅ ¾” Washers (#70). Insert the Arm Curl Stand into the front opening on the Main Frame (#27) and secure it with a Lock Knob (#61) to hold it at the desired height. B.) Remove the Arm Curl when using the Leg Developer to exercise.
STEP 5 (See Diagram 5) A.) Note: Do not tighten the Nuts and Bolts until instructed to do so. B.) Attach the top of Left Support (#2) to an Upright Beam (#1). Secure it with two M10 x 5/8” Allen Bolts (#82) and Ø ¾” Washers (#69). C.) Attach the Left Floor Stabilizer (#4) to the Upright Beam. Secure it with one M10 x 4” Carriage Bolt (#73), ∅ ¾” Washer (#69), and M10 Aircraft Nut (#72). D.) Attach the other end of the Left Floor Stabilizer (#4) and Rear Stabilizer (#7) to the bottom of Left Support (#2).
STEP 6 (See Diagram 6) A.) Attach the Rear Vertical Frame (#9) onto the Rear Base (#8). Secure it with two M10 x 2 ½” Carriage Bolts (#74), Ø ¾” Washers (#69), and M10 Aircraft Nuts (#72). B.) Attach the Rear Base (#8) and Front Vertical Frame (#10) to the Rear Stabilizer (#7). Align the holes and secure them together with two M10 x 2 ½” Carriage Bolts (#74), Ø ¾” Washers (#69), and M10 Aircraft Nuts (#72). C.) Align the Front Vertical Frame (#10) to the Cross Brace (#6).
DIAGRAM 6 12
CABLE LOOP DIAGRAM 13
STEP 7 (See Diagram 7 & Cable Loop Diagram) A.) Attach the 113 7/8” Upper Cable (#24) to the front opening on the Upper Frame (#11). Make sure the ball stopper of the Cable is underneath the Frame. B.) Attach a Pulley (#45) to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#77), two 5/8” Pulley Bushings (#65), and one M10 Aircraft Nut (#72). C.) Draw the Cable along the Upper Frame towards the back of the machine to the open bracket on the Upper Frame.
STEP 8 (See Diagram 8 & Cable Loop Diagram) A.) Attach the 58 1/8” Lower Cable (#25) to the lower opening on the bottom of Front Vertical Frame (#10). Attach a Pulley (#45) to the opening and secure it with one M10 x 2 3/8” Allen Bolt (#78), two ½” Pulley Bushings (#66), and one M10 Aircraft Nut (#72). B.) Pull the Cable underneath the Pulley to the open bracket on the Rear Base (#8).
STEP 9 (See Diagram 9) A.) Attach a Weight Post (#20) to the Right Support (#3). Secure it with a M10 x ¾” Allen Bolt (#81) and Ø ¾” Washer (#69). Slide an Olympic Sleeve (#44) onto the Post. Repeat the same procedure to install the other side. B.) Insert the Left & Right Bar Catches (#15 & 16), Left & Right Safety Catches (#13 & 14) into the selected holes on the Upright Beams (#1).
17
RACK EXPLODED DIAGRAM 18
PARTS LIST KEY NO.
IMPEX INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX.
