NOTE: Please read all instructions carefully before using this product Table of Contents MARCY® HOME GYM Safety Notice Hardware Identifier MWM-1509 Assembly Instruction Parts List Resistance Chart Warranty Ordering Parts Model MWM-1509 Retain This Manual for Reference 111102 OWNER'S MANUAL IMPEX® INC. 14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746 Tel: (800) 999-8899 Fax: (626) 961-9966 www.impex-fitness.com info@impex-fitness.
TABLE OF CONTENTS BEFORE YOU BEGIN....................................................................................……….. 1 IMPORTANT SAFETY NOTICES...................................................................……….. 2 HARDWARE PACK……….....….....................................................................……….. 4 ASSEMBLY INSTRUCTIONS.........................................................................………..
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual and all posted warning labels before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2.
WARNING LABEL REPLACEMENT The warning labels shown here have been placed on the Rear Base and Upper Frame. If the labels are missing or illegible, please call customer service at 1-800-888-8899 for replacements. Apply the labels in the location shown.
HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches, two Allen Wrenches, and one Philips Screwdriver. NOTE: It is strongly recommended this machine be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Connect two Lower Guide Rods (#46) and two Upper Guide Rods (#45) with two M10 Stud Bolts (#48). Firmly thread the Rods together. B.) Insert the two Lower Guide Rods (#46) into the holes on the Rear Base Frame (#2).
DIAGRAM 1 8
STEP 2 (See Diagram 2) A.) Slide 9 Weight Plates (#66) onto the Guide Rods. Make sure the grooves on the Weight Plates are all facing the back of the machine and downward. Insert the Selector Rod (#47) through the center hole on the Weight Plates. B.) Slide the Selector Stem (#65) onto the Guide Rods. C.) Slide the Ring on the Selector Pin (#67) onto the Selector Rod. Insert the Selector Pin into the selected groove to choose the number of weight plates for exercise.
DIAGRAM 2 10
STEP 3 (See Diagram 3) A.) Attach the Left Butterfly (#10) to the open bracket on the Front Press Base (#9). Secure it with one M12 x 4” Hex Bolt (#84), two Ø 1” Washers (#88), and one M12 Aircraft Nut (#91). B.) Slide a Butterfly Foam Roll (#57) onto the Left Butterfly arm. C.) Repeat Steps A&B above to install the Right Butterfly (#11). D.) Attach two 1 ¾” Spacers (#61) to the Lower & Upper Vertical Frames (#4 & #15). Attach the Backrest Board (#38) to the Spacers.
CABLE LOOP DIAGRAM 12
STEP 4 (See Diagram 4 & Cable Loop Diagram) A.) Attach the 122” Upper Cable (#40) to the open bracket underneath the front of Upper Frame (#8). B.) Attach a Pulley (#49) to the open bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#75), two Ø ¾” Washers (#86), and one M10 Aircraft Nut (#90). Note: The Ball Stopper on the Cable should be underneath the Frame and Pulley. C.) Draw the Cable towards the back of the machine to the open bracket under the Upper Frame.
DIAGRAM 4 14
STEP 5 (See Diagram 5 & Cable Loop Diagram) A.) Attach one end of the 119” Butterfly Cable (#41) to the hook on the Right Butterfly (#11). B.) Draw the Cable to the right open bracket on the back of Upper Vertical Frame (#15). C.) Attach a Pulley to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#75), two Ø ¾” Washers (#86), and one M10 Aircraft Nut (#90). D.) Draw the Cable over the Pulley then downward. Attach the Cable to a Crossed Double Floating Pulley Bracket (#14). Install a Pulley.
STEP 6 (See Diagram 6 & Cable Loop Diagram) A.) Attach the 130” Lower Cable (#39) to the opening on the bottom of the Leg Developer (#7). B.) Attach a Pulley (#49) to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#77), two Pulley Bushings (#33), and one M10 Aircraft Nut (#90). C.) Draw the Cable underneath the Pulley through the opening on the Lower Vertical Frame (#4) to the open bracket on the back. D.) Attach a Pulley to the open bracket.
DIAGRAM 6 17
EXPLDOED DIAGRAM 18
PARTS LIST KEY NO.
WM-1509 WEIGHT RESISTANCE CHART WEIGHT PLATE Station 1 2 3 4 5 6 7 8 9 Front Press 30 42 54 66 78 90 102 114 126 Butterfly 15 20 25 30 35 40 45 50 55 Lat Pull 30 40 50 60 70 80 90 100 110 Low Pulley 30 40 50 60 70 80 90 100 110 Leg Developer 30 40 50 60 70 80 90 100 110 * Each plate weights approximately 10 lbs. *Numbers are approximate. Actual weight may vary. *Value for butterfly is for each arm.
® IMPEX INC. LIMITED WARRANTY ® IMPEX Inc. ("IMPEX ") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX.
