NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice Hardware Identifier Assembly Instruction MARCY HOME GYM MWM-7300 Parts List Resistance Chart Warranty Ordering Parts Model MWM-7300 Retain This Manual for Reference 09-15-08 OWNER'S MANUAL IMPEX® INC. 14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746 Tel: (800) 999-8899 Fax: (626) 961-9966 www.impex-fitness.com info@impex-fitness.
TABLE OF CONTENTS BEFORE YOU BEGIN....................................................................................……….. 1 IMPORTANT SAFETY NOTICE...................................................................……….. 2 HARDWARE PACK……….....….....................................................................……….. 4 ASSEMBLY INSTRUCTIONS.........................................................................……….. 6 PARTS LIST………………………………………………………………………………….. 23 RESISTANCE CHART…………....................
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person at a time should use the machine. 3.
WARNING LABEL REPLACEMENT The warning labels shown here have been placed on the Base Frame and Upper Frame. If the labels are missing or illegible, please call customer service at 1-800-888-8899 for replacements. Apply the labels in the location shown.
HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler or scale to measure the size.
HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler or scale to measure the size.
ASSEMBLY INSTRUCTION Tools Required for Assembling the Machine: Two Adjustable Wrenches, two Allen Wrenches, and one Philips Screwdriver. NOTE: It is strongly recommended that this machine to be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Do not tighten Nuts and Bolts until instructed to do so. B.) Attach the front of Main Base Frame (#1) onto the Foot Plate (#7). Secure it with two M10 x 2 1/8” Allen Bolts (#80) and two Ø ¾” Washers (#91). C.
DIAGRAM 1 7
STEP 2 (See Diagram 2) A.) Slide two Ø 2 ½” x 1” Rubber Bumpers (#65) onto the Guide Rods (#18). Attach the two Guide Rods onto the Weight Stack Frame (#17). Secure the bottom of Guide Rods with two M10x 1” Allen Bolts (#82) and two Ø ¾” Washers (#91). B.) Pull the top of the two Guide Rods off the Weight Stack Frame. Slide 14 Weigh Plates (#59) onto the Guide Rods. Make sure the deep groove on the Weight Plates are all facing the machine and downward. C.
DIAGRAM 2 9
STEP 3 (See Diagram 3) A.) Do not tighten Nuts and Bolts until instructed to do so. B.) Attach the Lower Cross Brace (#16) to the Weight Stack Frame (#17). Secure them with two M10 x 3 1/8” Carriage Bolts (#72), one 5 1/8” x 1 5/8” Bracket (#58), two Ø ¾” Washers (#91), and two M10 Aircraft Nuts (#94). C.) Attach the Upper Cross Brace (#15) to the Rear Vertical Frame (#3) and Upper Frame (#4).
DIAGRAM 3 11
STEP 4 (See Diagram 4) A.) Attach the Right & Left Seat Swivel Frame (#13) & (#14) to Main Base Frame (#1) from each side. Secure them together with one M12 x 7 7/8” Allen Bolt (#74), two Ø 1” Washer (#90), and one M12 Aircraft Nut (#93). Do not over tighten the Nut and Bolt. Make sure the Swivel Frames are able to swivel smoothly. B.) Repeat above procedure to install the two Front Seat Swivel Frames (#12). C.) Attach the Seat Support to the top of the two Seat Swivel Frames and Swivel Supports.
CABLE LOOP DIAGRAM 13
STEP 5 (See Diagram 5 & Cable Loop Diagram) A.) Attach the 205” Upper Cable (#35) to the opening at the front of the Upper Frame (#5). Note: The Ball Stopper on the cable need to be underneath the Frame. B.) Attach a Pulley (#51) to the opening. Secure it with one M10 x 4 1/8” Allen Bolt (#77), two Ø ¾” Washers (#91), and one M10 Aircraft Nut (#94). C.) Draw the Cable towards the back of the machine to the opening on the Upper Frame. Repeat B to install a Pulley. D.
DIAGRAM 5 15
STEP 6 (See Diagram 6 & Cable Loop Diagram) A.) Attach the 118” Lower Cable (#36) to the opening on the bottom of the Leg Developer (#10). B.) Attach a Pulley (#51) to the opening. Secure it with one M10 x 3 3/8” Allen Bolt (#78), two Ø ¾” (#91), and one M10 Aircraft Nut (#94). C.) Draw the Cable underneath the Pulley to the open bracket on Main Base Frame (#1). D.) Attach a Pulley to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#81), two Ø ¾” (#91), and one M10 Aircraft Nut (#94). E.
DIAGRAM 6 17
STEP 7 (See Diagram 7) A.) Attach the Front Weight Stack Cover (#29) to the Weight Stack Frame (#17). Secure it with six M6 x 2 ½” Philips Screws (#89) and six Cover Spacers (#54). B.) Repeat the Procedure A to install the Rear Weight Stack Cover (#30) to the other side.
STEP 8 (See Diagram 8) A.) Attach the Backrest Board (#34) to Front Vertical Frame (#2). Secure it with two M8 x 2 1/8” Allen Bolts (#85) and two Ø 5/8” Washers (#92). B.) Attach the Seat Pad to Seat Support (#11). Secure it with two M8 x 2 1/8” Allen Bolts (#85) and two Ø 5/8” Washers (#92). C.) Insert two Foam Tubes (#19) halfway through the holes on Seat Support and Leg Developer (#10). Push four Foam Rolls (#55) onto the Tubes from both ends. Plug four Foam Roll End Caps (#44) into the Ends. D.
DIAGRAM 8 20
STEP 9 (See Diagram 9) A.) Attach the Front Press (#6) to the Front Press Base (#5). Secure it with one 8 ¾” Long Axle (#57), two Ø ¾” Washers (#91), and two M10 Aircraft Nuts (#94). Do not over tighten the Nuts. Make sure the Front Press is able to swivel smoothly. B.) Use the T-shaped Lock Pin (#40) to lock the Front Press to the Front Press Base in desired position. C.) Connect the Lat Bat (#21) to Upper Cable with two Hooks (#69) and one Short Chain (#67). D.
22
PARTS LIST KEY NO.
MWM-7300 WEIGHT RESISTANCE CHART WEIGHT PLATE Station 1 2 3 4 5 6 7 8 9 Lat Pull 10 20 30 40 50 60 70 80 90 Front Press 15 26 37 48 59 70 81 92 103 Low Pulley 10 20 30 40 50 60 70 80 90 Leg Developer 15 29 43 57 71 85 99 113 127 Leg Press 30 60 90 120 150 180 210 240 270 WEIGHT PLATE Station 10 11 12 13 14 Lat Pull 100 110 120 130 140 Front Press 114 125 136 147 158 Low Pulley 100 110 120 130 140 Leg Developer 141 155 169
® IMPEX INC. LIMITED WARRANTY ® IMPEX Inc. ("IMPEX ") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX.
