NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice Hardware Pack Assembly Instruction MARCY® MWM 980 HOME GYM Parts List Resistance Chart Warranty Ordering Parts Model MWM-980 Retain This Manual for Reference 08-07-09 OWNER'S MANUAL IMPEX® INC. 14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746 Tel: (800) 999-8899 Fax: (626) 961-9966 www.impex-fitness.com info@impex-fitness.
TABLE OF CONTENTS BEFORE YOU BEGIN....................................................................................……….. 1 IMPORTANT SAFETY NOTICES...................................................................……….. 2 HARDWARE IDENTIFIER.....….....................................................................……….. 4 ASSEMBLY INSTRUCTIONS.........................................................................……….. 6 PARTS LIST…………………………………………………………………………………. 24 RESISTANCE CHART………….................
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person at a time should use the machine. 3.
WARNING LABEL REPLACEMENT The warning labels shown here have been placed on the Rear Stabilizer and Upper Frame. If the labels are missing or illegible, please call customer service at 1-800-888-8899 for replacements. Apply the labels in the location shown.
HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
ASSEMBLY INSTRUCTION Tools Required for Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended this machine to be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Insert the two Guide Rods (#17) into the holes on the Rear Stabilizer (#4). Secure each Guide Rod with one M10 x ¾” Allen Bolt (#60) and ∅ ¾” Washer (#65) from the bottom. The Guide Rods have holes on the rods to lock the weight stack when not in use.
DIAGRAM 1 7
STEP 2 (See Diagram 2) A.) Attach the Leg Developer Holder (#5) onto the Base Frame (#3). Secure it with two M10 x 2 ¾” Carriage Bolts (#55), one 1 ¾” x 4 ¾” Bracket (#20), two ∅ ¾” Washers (#65), and two M10 Aircraft Nuts (#69). B.) Attach the Seat Support (#6) to the Vertical Frame (#2). Secure it with two M10 x 2 ¾” Carriage Bolts (#55), one 1 ¾” 4 ¾” Bracket (#20), two ∅ ¾” Washers (#65), and two M10 Aircraft Nuts (#69). C.) Attach the other end of Seat Support to the Leg Developer Holder.
DIAGRAM 2 9
STEP 3 (See Diagram 3) A.) Attach the Weight Stack Cover (#16) to the bracket on Rear Stabilizer (#4) and Upper Frame (#1). B.) Attach two Weight Stack Cover Brackets (#29) to top and bottom of Weight Stack Cover. C.) Secure the Weight Stack cover Bracket, Weight Stack Cover to Upper Frame with four M6 x ¾” Allen Bolts (#63), four Ø ½” Washers (#67), and two M6 Aircraft Nuts (#70). D.
STEP 4 (See Diagram 4) A.) Attach the Front Press Base (#8) to the Upper Frame (#1). Secure it with one 3” Front Press Axle (#38), two Ø ¾” Spacers (#68), and two M10 Aircraft Nuts (#69). Do not over tighten the Nuts. B.) Attach the Right Butterfly (#9) to the open bracket on Front Press Base. Secure it with one 2 5/8” Butterfly Axle (#39), two Ø ¾” Spacers (#68), and two M10 Aircraft Nuts (#69). Push one large Foam Roll (#27) onto the Right Butterfly. C.
DIAGRAM 4 12
STEP 5 (See Diagram 5) A.) Attach the Backrest Board (#24) to the Vertical Frame (#2). Secure it with two M8 x 2 ¾” Allen Bolts (#61) and two Ø 5/8” Washers (#66). B.) Attach the Seat Pad (#25) to the Seat Support (#6). Secure it with four M8 x 5/8” Allen Bolts (#62) and two Ø 5/8” Washers (#66).
STEP 6 (See Diagram 6) A.) Attach one Swivel Pulley Bracket (#14) to the open bracket on the back of Vertical Frame (#2). Secure it with one M10 x 2 ½” Allen Bolt (#57), two Ø ¾” Washers (#65), and one M10 Aircraft Nut (#69). Do not over tighten the Nut and Bolt. Make sure the Swivel Pulley Bracket can swivel freely. B.) Repeat Procedure A to install the other Swivel Pulley Bracket on the other side. C.) Attach two Butterfly Cable Brackets (#12) to the Right & Left Butterfly (#9 & #10).
DIAGRAM 6 15
CALBE LOOP 16
STEP 7 (See Diagram 7 & Cable Loop Diagram) A.) Attach the 116” Upper Cable (#48) to the front opening on the Upper Frame. NOTE: The Ball Stopper on the Cable needs to be underneath the Frame. B.) Attach a Pulley (#42) to the opening. Secure it with one M10 x 2 ¾” Allen Bolt (#56), two Ø 7/8” Pulley Bushings (#43) pre-installed on Upper Frame, and one M10 Aircraft Nut (#69). C.) Draw the Cable towards the back of the machine to the second opening on the Upper Frame.
DIAGRAM 7 18
STEP 8 (See Diagram 8 & Cable Loop Diagram) A.) Attach one end of the 91” Butterfly Cable (#49) to one Butterfly Cable Bracket (#12). Secure it with one M10 x ¾” Allen Bolt (#60) and one M10 Aircraft Nut (#65). B.) Draw the Cable towards the right open Swivel Pulley Bracket (#14). C.) Attach a Pulley (#42) to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#59), two ∅ ¾” Washers (#65), and one M10 Aircraft Nut (#69). D.) Draw the Cable over the Pulley then pull downward.
STEP 9 (See Diagram 9 & Cable Loop Diagram) A.) Attach the 134” Lower Cable (#50) to the opening on the bottom of the Leg Developer (#7). B.) Attach a Pulley (#42) to the opening. Secure it with one M10 x 2 ¾” Allen Bolt (#56), two ∅ 7/8” Pulley Bushings (#43) pre-installed on the holes, and one M10 Aircraft Nut (#69). C.) Draw the Cable underneath the Pulley towards the back of the machine through the opening on the Leg Developer Holder (#5). Repeat Procedure B to install a Pulley. D.
DIAGRAM 9 21
STEP 10 (See Diagram 10) A.) Attach Lat Bar (#18) to the Upper Cable (#48) with two C-Clips (#34) and one Chain (#33) when doing Lat Pull exercises. B.) Attach Lat Bar to the Lower Cable (#50) with two C-Clips (#34) and one Chain (#33) when doing Arm Curl exercises C.) Remove Arm Curl Stand. Replace Lat Bar with the Ankle Strap (#47) to the Lower Cable (#50) for various leg exercises. D.
Set up the Lock Combination A.) The combination is pre-set at 0-0-0 by the factory. B.) Turn the dials to 0-0-0 and aligned to the Combination Set Up Line. 0. C.) Pull out the shackle and turn 180 D.) Press down on the shackle. E.) Turn the dials (aligned to the Combination Set Up Line) to your desired combination. F.) Pull out the shackle and twist back to normal position and the combination are set. G.) Repeat Procedure C to F to re-set the combination.
PARTS LIST KEY NO.
MWM980 WEIGHT RESISTANCE CHART Weight Plate 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Front Press 31 44 57 70 83 96 109 122 135 148 161 174 187 200 Butterfly 15 20 25 30 35 40 45 50 55 60 65 70 75 80 Lat Pull 30 40 50 60 70 80 90 100 110 120 130 140 150 160 Note: Each plate weights 10 lbs. Numbers are approximate. Actual weights may vary. Values for Butterfly are for each arm.
® IMPEX INC. LIMITED WARRANTY ® IMPEX Inc. ("IMPEX ") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX.
