NOTE: Please read all instructions carefully before using this product Table of Contents MARCY SMITH MACHINE Safety Notice MXM-5 Hardware Identifier Assembly Instruction Parts List Warranty Ordering Parts Model MXM-5 Retain This Manual for Reference 09-01-05 OWNER'S MANUAL IMPEX 14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746 Tel: (800) 999-8899 Fax: (626) 961-9966 www.impex-fitness.com info@impex-fitness.
TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................... IMPORTANT SAFETY NOTICES..................................................................... HARDWARE PACK….......…..........................................………………………. ASSEMBLY INSTRUCTIONS...........................................……………………. EXPLODED DIAGRAM…………………………………………………………….. PARTS LIST………..……………………………………………………………….. WARRANTY........................................................
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person at a time should use the machine. 3.
WARNING LABEL REPLACEMENT The warning labels shown here have been placed on the Cross Brace and Upper Frame. If the labels are missing or illegible, please call customer service at 1-800-888-8899 for replacements. Apply the labels in location shown.
HARDEWARE PACK 4
HARDEWARE PACK 5
HARDEWARE PACK 6
HARDEWARE PACK 7
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches NOTE: It is strongly recommended two or more people assembling this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) NOTE: Do not tighten the Nuts and Bolts until instructed to do so. B.) Connect the Left & Right Base Frames (#17 & #18) by a Cross Brace (#20) in the midspan.
DIAGRAM 1 9
STEP 2 (See Diagram 2) A.) Attach the Rear Vertical Beam (#23) onto the Cross Brace (#20). Attach the Weight Glide Post (#22) to the Rear Vertical Beam and Cross Brace. Align the holes and secure them with two M10 x 2 ¾” Carriage Bolts (#93), ∅ ¾” Washers (#82), and M10 Aircraft Nuts (#99). B.) Slide the Sliding Weight Post (#34) onto the Weight Glide Post (#22). C.) Place the Upper Frame (#21) onto the Rear Vertical Beam (#23), Weight Glide Post (#22), and Front Top Beam (#32). D.
DIAGRAM2 11
STEP 3 (See Diagram 3) A.) Attach the Butterfly Base (#24) and Butterfly Pulley Bracket (#33) to the Rear Vertical Beam (#23). Align the holes and secure them with two M10 x 2 ½” Carriage Bolts (#92), ∅ ¾” Washers (#82), and M10 Aircraft Nuts (#99). B.) Insert the pivot on the Right Butterfly (#26) through the hole on the Butterfly Base. Secure it with one Lock Ring (#73), M6 x 1 ¼” Allen Screw (#100), and M6 Aircraft Nut (#101). C.) Push a Butterfly Arm Pad (#49) onto the Right Butterfly. D.
STEP 4 (See Diagram 4) A.) Note: Help of another person is strongly recommended for this step. Place the Weight Lifting Sleeve (#38) in between the two Safety Stop Frames (#37). Align the holes and insert the Weight Bar (#39) into the Safety Stop Frame from one end through the Weight Lifting Sleeve to the other Safety Stop Frame on the opposite end. Secure the Weight Bar to each Safety Stop Frame with a M8 x 3/8” Allen Bolt (#103). B.
CABLE LOOP DIAGRAM 14
STEP 5 (See Diagram 5 & Cable Loop Diagram) A.) Attach a 124” Cable (#51) to the front opening on the Upper Frame (#21). Attach a Pulley (#74) to the opening. Secure it with one M10 x 2 1/8” Allen Bolt (#87), two Ø 7/8” Bushings (#79), and one M10 Aircraft Nut (#99). Make sure the ball stopper of the Cable is underneath the Upper Frame. B.) Draw the Cable over the Pulley along the Upper Frame to the opening on the rear of Upper Frame. Attach a Pulley to the opening.
DIAGRAM 5 16
STEP 6 (See Diagram 6 & Cable Loop Diagram) A.) Attach one end of the 79” Butterfly Cable (#52) to the clip on the Left Butterfly (#25). Draw the Cable to the left Butterfly Pulley Bracket (#33). B.) Attach a Pulley (#74) to the Bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#86), two ∅ ¾” Washers (#82), and one M10 Aircraft Nut (#99). C.) Draw the Cable around the Pulley then downward. Attach the Cable to a Single Floating Pulley Bracket (#36). Install a Pulley to the Bracket.
STEP 7 (See Diagram 7 & Cable Loop Diagram) A.) Attach one 124” Cable (#51) to the lower opening on the Rear Vertical Beam (#23). Attach a Pulley to the opening. Secure it with M10 x 2 3/8” Allen Bolt (#88), two Ø 1” Bushings (#78), and one M10 Aircraft Nut (#99). B.) Draw the Cable underneath the Pulley to the open bracket on the Weight Glide Post (#22). Attach a Pulley to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#86), two ∅ ¾” Washers (#82), and one M10 Aircraft Nut (#99). C.
STEP 8 (See Diagram 8) A.) Attach the Main Seat Support (#1) to the Front & Rear Stabilizers (#3 & #4). B.) Secure each end with two M10 x 3 1/8” Carriage Bolts (#94), one 4 ¾” Curve Bracket (#8), two ∅ ¾” Washers (#82), and two M10 Aircraft Nuts (#99).
STEP 9 (See Diagram 9) A.) Do not tighten all nuts and bolts until instructed to so. B.) Attach the Leg Developer Holder (#2) to the Main Seat Support. Secure it with two M10 x 3 1/8” Carriage Bolts (#94), one 6 ¼” Curve Bracket (#9), two ∅ ¾” Washers (#82), and two M10 Aircraft Nuts (#99). C.) Attach the Backrest Supports (#5) to the bracket on the Main Seat Support. Attach the seat support on the Leg Developer Holder (#2) to the inside of the open bracket.
STEP-10 (See Diagram 10) A.) Attach the Leg Developer (#7) to the Leg Developer Holder (#2). Secure it with one M10 x 3 1/8” Allen Bolt (#90), two ∅ ¾” Washers (#82), and one M10 Aircraft Nut (#99). Do not over tighten the nut and bolt. Make sure the Leg Developer is able to swivel. B.) Insert three Foam Tubes (#15) halfway through the holes on the Leg Developer Holder and Leg Developer. Push six Foam Rolls (#53) onto the Tubes. Plug six Foam Roll End Caps (#55) into the Tubes. C.
STEP-11 (See Diagram 11) A.) Attach the Arm Curl Pad (#14) to the Arm Curl Stand (#13). Secure it with two M8 x ¾” Allen Bolts (#96) and ∅ 5/8” Washers (#81). B.) Insert the Arm Curl Stand into the opening on the Leg Developer Holder. Use a Lock Knob (#58) to secure it in position. Remove the Arm Curl Stand and Curl Bar Holder Frame when doing leg exercises.
SMITH MACHINE EXPLODED DIAGRAM 23
24
PARTS LIST KEY NO.
IMPEX LIMITED WARRANTY IMPEX warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX Customer Service Department at 1-800-999-8899.
