NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice Hardware Pack Magnetic-Resistance Elliptical Exerciser NS-40501E Assembly Instruction Parts List Warranty Ordering Parts Model NS-40501E Retain This Manual for Reference 140926 ASSEMBLY & OWNER'S MANUAL IMPEX® INC. 2801 S. Towne Ave, Pomona, CA 91766 Tel: (800) 999-8899 Fax: (626) 961-9966 www.impex-fitness.com support@impex-fitness.
TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................…. IMPORTANT SAFETY NOTICES..................................................................…. WARNING LABEL PLACEMENT………………………………………………….. HARDWARE PACK …………………………………………………………………. ASSEMBLY INSTRUCTIONS........................................................................…. EXPLODED DIAGRAM………………………………………………………………. PARTS LIST.................................................................
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person at a time should use the machine. 3.
WARNING LABEL PLACEMENT The Warning Labels shown here has been placed on the Rear Stabilizer. If the labels are missing or illegible, please call customer service at 1-800-999-8899 for replacement. Apply the labels in location shown. © IMPEX INC. 3 www.impex-fitness.
HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. © IMPEX INC. NO.
29 Hex Bolt M10 x ¾” 2 30 Lock Washer Ø ⅜” 2 31 Ø 1 ¼” x Ø ⅜” 2 32 D Washer 2 12 Flat Washer Ø 1 ⅛” 2 51L/R Hex Nut 1/1 41 © IMPEX INC. Curve Washer Ø ¾” x Ø ⅜” 6 Allen key L6 1 Allen key L4 1 Allen key L8 1 Allen wrench 2 5 www.impex-fitness.
COMPONENTS FOR ASSEMBLY © IMPEX INC. 6 www.impex-fitness.
ASSEMBLY INSTRUCTION • Tools Required For Assembling the Machine: One Crossing Wrench and Allen Wrench, provided by manufacturer. • NOTE: It is strongly recommended that two or more people assemble this machine to avoid possible injury. STEP-1 A.) Attach the Rear Stabilizer (#2) to the Main Frame (#1). Secure it with two M8 x 3” Carriage Bolts (#6), two Ø ⅞” Curved Washers (#7), and two Acorn Nuts (#8). B.) Attach the Front Stabilizer (#3) to the Main Frame.
STEP-2 A.) Remove the Tension Knob Screw (#50) and Ø ½” Washer (#49) from the Tension Knob. B.) Insert the Upper Tension Cable (#25) through the opening on Front Post to the bottom of the Front Post. C.) Plug the Tension Knob (#25) into the opening, secure the Tension Knob to Front Post with the Tension Knob Screw (#50) and the Ø ½” Washer (#49). © IMPEX INC. 8 www.impex-fitness.
STEP-3 A.) NOTE: Extra help may be needed to hold the Front Post (#22) while connecting the cables and wires. B.) Attach the Front Post (#22) to the Main Frame (#1). Connect the Upper Computer Wire (#26) from the bottom of the Front Post to the Lower Computer Wire (#28) from the Main Frame. C.) Pull the tension connector from the Upper Tension Cable (#25) and slide in between the opening on the connector on the Lower Tension Cable (#27).
STEP-4 A.) Attach left Stride Tube (#21L) to the left axle on Front Post (#22). B.) Secure the Stride Tube (#21L) to Front Post with one D Washer (#32), one Ø 1 ¼” x Ø ⅜” Flat Washer (#31), one Ø ⅜” Lock Washer (#30), and one M10 x ¾” Hex Bolt (#29). C.) Cover the pivot joint with two left Stride Tube Covers (#47L) and secure them together with two ST5 x ⅝” Self Tapping Screws (#33). D.
STEP-5 A.) Do not tighten Nuts and Bolts until instructed to do so. B.) Place the pivot on bottom of left Stride Tube (#21L) to the open bracket on Left Pedal Support (#9L). Secure the Tube to the Left Pedal Support with one M10 x 3 ⅛” Hex Bolt (#20), one Sleeve (#18), one Ø ¾” Washer (#17), and one M10 Aircraft Nut (#16). C.) Attach the Left Pedal Support rear pivot to the Crank (#24).
STEP-6 A.) Do not tighten Nuts and Bolts and Nuts until instructed to so. B.) Place the pivot on bottom of right Stride Tube (#21R) to the open bracket on Right Pedal Support (#9R). Secure the Tube to the right Pedal Support with one M10 x 3 ⅛” Hex Bolt (#20), one Sleeve (#18), one Ø ¾” Washer (#17), and one M10 Aircraft Nut (#16). C.) Attach the Right Pedal Support rear pivot to the Crank (#24).
STEP-7 A.) Attach the Stationary Handle (#39) to Front Post (#22). Secure it with two M8 x ⅝” Allen Bolts (#23) and two Ø ¾” x Ø ⅜” Curve Washers (#41). B.) Remove four M5 x ½”Philips Screws (#48) from Computer (#38). Connect the computer wire from Computer to the Upper Computer Wire (#26) from Front Post. Slide the computer onto the bracket on Front Post. Secure the Computer to the bracket with the four M5 x ½”Philips Screws (#48). © IMPEX INC. 13 www.impex-fitness.
STEP-8 A.) Place the left Stride Handle (#37L) onto left Stride Tube (#21L). Secure it with two M6 x ¾” Carriage Bolts (#36) and two M6 x ½” Allen Bolts (#35). B.) Repeat A to install right Stride Handle (#37R) to right Stride Tube (#12R). © IMPEX INC. 14 www.impex-fitness.
EXPLODED DIAGRAM © IMPEX INC. 15 www.impex-fitness.
EXPLODED DIAGRAM © IMPEX INC. 16 www.impex-fitness.
NS-40501E PARTS LIST PART NO. 1 2 3 4 5 6 7 8 9L 9R 10L 10R 11 12 13L 13R 14 15 16 17 18 19 20 21L/R 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37L/R © IMPEX INC. DESCRIPTION SPEC.
38 39 40 41 42 43 44 45 46L/R 47L/R 48 49 50 51L/R 52 53 54L/R 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 © IMPEX INC.
CARE, MAINTENANCE AND STORAGE 1. Inspect and tighten all parts each time you use the machine. Replace any worn parts immediately. 2. The machine can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents. 3. Store the bike IN-DOOR. Excess moisture and water would cause rust on the frame. 4. The Bike shall be placed at least 24 inches away from the wall or/and any other object such as furniture to provide safe access to and passage around the machine. 5.
COMPUTER AUTO START / STOP When exercise starts, the monitor will automatically turn on and display the progress. When exercise stops, the monitor will automatically turn off after 4 minutes to save energy. MODE1. Press “MODE” key, will automatically scan Time, Speed, Distance, Calories, and ODO for every 4 seconds. 2. When Computer is in Scan mode, press “MODE” key to select Time, Distance, or Calories function. SETPress SET key to set the targeted exercises value of Time, Distance, and Calories.
EXERCISE GUIDELINES Using your MAGNETIC BIKE will provide you with several benefits, it will improve your physical fitness, tone muscle and in conjunction with calorie controlled diet help you lose weight. 1. The Warm Up Phase This stage helps get the blood flowing around the body and the muscles working properly. It will also reduce the risk of cramp and muscle injury. It is advisable to do a few stretching exercises as shown below.
3. The Cool Down Phase This stage is to let your Cardio-vascular System and muscles wind down. This is a repeat of the warm up exercise e.g. reduce your tempo, continue for approximately 5 minutes. The stretching exercises should now be repeated, again remembering not to force or jerk your muscles into the stretch. As you get fitter you may need to train longer and harder. It is advisable to train at least three times a week, and if possible space your workouts evenly throughout the week.
® IMPEX INC. LIMITED WARRANTY ® IMPEX Inc. ("IMPEX ") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX.