NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice Hardware Identifier Assembly Instruction Parts List POWERHOUSE OLYMPIC BENCH PHC 2000 Warranty Ordering Parts Model PHC-2000 Retain This Manual for Reference 07-28-03 OWNER'S MANUAL IMPEX FITNESS PRODUCTS 14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746 Tel: (800) 999-8899 Fax: (626) 961-9966 www.impex-fitness.com info@impex-fitness.
TABLE OF CONTENTS BEFORE YOU BEGIN....................................................................................……….. 1 IMPORTANT SAFETY NOTICES...................................................................……….. 2 HARDWARE PACK……….....….....................................................................……….. 3 ASSEMBLY INSTRUCTIONS.........................................................................……….. 5 EXPLODED DIAGRAM…………………………………………………………………….. 10 PARTS LIST………….…………...................
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person at a time should use the machine. 3.
HARDWARE PACK 3
HARDWARE PACK 4
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended this machine to be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Attach the Right Upright Beam (#1) to a Rear Stabilizer (#3). Secure it with two M10 x 4 ¾” Carriage Bolts (#49), one 5 ½” x 2” Bracket (#29), two Ø ¾” Washers (#56), and two M10 Aircraft Nuts (#58). Do not tighten the Nut and Bolts yet. B.
STEP 2 (See Diagram 2) A.) Slide the Sliding Block (#7) onto the Main Seat Support (#6). Thread a M18 x ∅3/8” Lock Knob (#32) into the selected hole to hold the Sliding Block in position. B.) Attach the Leg Developer Holder (#9) to the Front Stabilizer (#25). Secure it with three M10 x 5/8” Allen Bolts (#52) and ∅ ¾” Washers (#56). C.) Attach the Main Seat Support (#6) to the Leg Developer Holder.
STEP 3 (See Diagram 3) A.) Attach the holes on the end of the Backrest Supports (#20) to the pivot on the Sliding Block (#7). Attach the Backrest Board (#21) to the Backrest Supports. Secure it with four M8 x 1 5/8” Allen Bolts (#55) and Ø5/8” Washers (#57). B.) Attach the Seat Bracket (#8) to the pivot on the Sliding Block. Secure it with one M10 x 4 ¾” Allen Bolt (#53), two Ø ¾” Washers (#56), and one M10 Aircraft Nut (#58). C.) Place the Seat (#22) onto the Seat Bracket.
STEP 4 (See Diagram 4) A.) Attach the Leg Developer (#11) to the Leg Developer Holder (#9). Secure it with an Axle (#36), two M10 x 5/8” Allen Bolts (#52) and two ∅ ¾” Washers (#56). B.) Insert one Foam Tube (#24) halfway through the hole on the Leg Developer Holder. Insert two Foam Tubes halfway through the holes on the Leg Developer. Push six Foam Rolls (#30) onto the Tubes from both ends. Plug six Foam Roll End Caps (#38) into the ends. C.
STEP 5 (See Diagram 5) A.) Attach the Arm Curl Pad (#63) to the Arm Curl Stand (#10). Secure it with two M8 x 5/8” Allen Bolts (#54) and Ø 5/8” Washers (#57). B.) Insert the Arm Curl Stand into the top opening on the Leg Developer Holder. Use a M18 x ∅½” Lock Knob (#33) to secure the Stand. C.) Attach the Curl Bar Handle Frame (#18) to the bracket on the Leg Developer (#11). Secure it with a 3” L-shaped Pin (#31). D.) Remove the Arm Curl Stand and the Curl Bar Handle when using the Leg Developer.
10
PARTS LIST KEY NO.
IMPEX INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX.
