NOTE: Please read all instructions carefully before using this product Safety Notice POWERHOUSE CLUB Hardware Identifier Assembly Instruction PHC 698 Parts List Warranty Ordering Parts Model PHC 698 Retain This Manual for Reference 07-11-01 OWNER'S MANUAL IMPEX FITNESS PRODUCTS 14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746 Tel: (800) 999-8899 Fax: (626) 961-9966 www.impex-fitness.com info@impex-fitness.
TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................... 1 IMPORTANT SAFETY NOTICES..................................................................... 2 HARDWARE IDENTIFIER.....…....................................................................... 3 ASSEMBLY INSTRUCTIONS........................................................................... 4 EXPLODED DIAGRAM……………………………………………………………... 8 PARTS LIST………………………………………………………………………..
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person at a time should use the machine. 3.
3
ASSEMBLY INSTRUCTION Tools Required to Assemble the Machine: Two Adjustable Wrenches and Allen Wrenches NOTE: It is strongly recommended this machine to be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Connect the Left & Right Upright Beams (#1) & (#2) by a Cross Brace (#3) in the mid-span.
STEP 2 (See Diagram 2) A.) Attach the back of the Main Seat Support (#10) to the Cross Brace (#3). Secure it with one 4 3/8” Bracket (#9), two M10 x 2 ½” Carriage Bolts (#36), two ∅ ¾” Washers (#37), and two M10 Aircraft Nuts (#38). B.) Slide the Sliding Block (#11) onto the Main Seat Support (#10). Secure it with a Lock Knob (#8). C.) Attach the Front Stabilizer (#12) to the Main Seat Support (#10). Secure it with two M10 x 2 ½” Carriage Bolts (#36), ∅ ¾” Washers (#37), and M10 Aircraft Nuts (#38). D.
STEP 3 (See Diagram 3) A.) Attach the Seat Bracket (#19) to the pivot on the Sliding Block (#11). Attach two Bushings (#20) to the holes. Attach two Backrest Supports (#22) to the Bushings. Align the holes and secure them with one M10 x 7 ¼” Hex Bolt (#40), two ∅ ¾” Washers (#37), and one M10 Aircraft Nut (#38). B.) Place the Backrest Incline Support (#21) in between the two Backrest Supports (#22).
STEP 4 (See Diagram 4) A.) Place Backrest Board (#24) onto Backrest Supports (#22). Secure it with four M8 x 1 5/8” Allen Bolts (#35) and ∅ 5/8” Washers (#34). B.) Place Seat (#25) onto the Seat Bracket (#19). Secure the two back holes with two M8 x 5/8” Allen Bolts (#33) and ∅ 5/8” Washers (#34). Secure the two front holes with a Seat Incline Adjustment (#18), two M8 x 5/8” Allen Bolts (#33) and ∅ 5/8” Washers (#34).
8
PARTS LIST KEY NO.
IMPEX INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX.
