NOTE: Please read all instructions carefully before using this product Safety Notice POWERHOUSE CLUB Hardware Identifier Assembly Instruction PHC 750 Parts List Warranty Ordering Parts Model PHC 750 Retain This Manual for Reference 09-26-01 OWNER'S MANUAL IMPEX FITNESS PRODUCTS 14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746 Tel: (800) 999-8899 Fax: (626) 961-9966 www.impex-fitness.com info@impex-fitness.
TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................... 1 IMPORTANT SAFETY NOTICES..................................................................... 2 HARDWARE IDENTIFIER.....…....................................................................... 3 ASSEMBLY INSTRUCTIONS........................................................................... 4 EXPLODED DIAGRAM……………………………………………………………... 8 PARTS LIST………………………………………………………………………..
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person at a time should use the machine. 3.
3
ASSEMBLY INSTRUCTION Tools Required to Assemble the Machine: Two Adjustable Wrenches and Allen Wrenches NOTE: It is strongly recommended this machine to be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Connect the two Upright Beams (#1) by a Cross Brace (#2) in the mid-span. Align the holes and secure them with one Bracket (#20), two M10 x 3 1/8” Carriage Bolts (#38), two ∅ ¾” Washers (#45), and two M10 Aircraft Nuts (#44) on each end of the Cross Brace. B.
STEP 2 (See Diagram 2) A.) Attach the Leg Developer Holder (#5) to the Front Stabilizer (#6). Secure it with three M10 x 5/8” Allen Bolts (#43) and ∅ ¾” Washers (#45). B.) Attach the Leg Developer Holder (#5) to the front of Main Seat Support (#3). Secure it with one M10 x 2 ½” Carriage Bolt (#56), two M10 x 2 ¾” Carriage Bolts (#39), three ∅ ¾” Washers (#45), and three M10 Aircraft Nuts (#44). C.) Attach the back of Main Seat Support (#3) to the Cross Brace (#2).
STEP 3 (See Diagram 3) A.) Attach the hole-side of the Seat Bracket (#11) to the Pivot on the Main Seat Support (#3). Push two Bushings (#36) into the holes on the Pivot. B.) Attach the Backrest Supports (#10) to the Pivot. Secure it with one M10 x 7 ¼” Hex Bolt (#41), two ∅ ¾” Washers (#45), and one M10 Aircraft Nut (#44). DO NOT tighten the nut and bolt yet. Place the Backrest Incline Support (#9) in between the two Backrest Supports (#10). Securely tighten the Nut (#44) and Bolt (#41). C.
STEP 4 (See Diagram 4) A.) Attach the Leg Developer (#14) to the bracket on top of the Leg Developer Holder (#5). Secure it with an Axle (#48), two ∅ ¾” Washers (#45), and two M10 x 5/8” Allen Bolts (#43). Slide the Olympic Sleeve (#55) onto the post on the Leg Developer. Attach a Spring Clip (#21) to the Sleeve. Note: When using the decline position to do Ab exercises, place at least 30lbs of weights on the Sleeve to hold down the Leg Developer. B.
8
PARTS LIST KEY NO.
IMPEX INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX.
