NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice Hardware Pack Assembly Instruction MARCY® PM-3800 POWER RACK Parts List Resistance Chart Warranty Ordering Parts Model PM-3800 Retain This Manual for Reference 110922 OWNER'S MANUAL IMPEX® INC. 2801 S. Towne Ave., Pomona, CA 91766 Tel: (800) 999-8899 Fax: (626) 961-9966 www.impex-fitness.com info@impex-fitness.
TABLE OF CONTENTS BEFORE YOU BEGIN....................................................................................……….. 1 IMPORTANT SAFETY NOTICES...................................................................……….. 2 HARDWARE IDENTIFIER.....….....................................................................……….. 4 ASSEMBLY INSTRUCTIONS.........................................................................………..
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person at a time should use the machine. 3.
WARNING LABEL PLACEMENT The warning labels shown here have been placed on the Bench Rear Stabilizer and Rear Base Frame. If the labels are missing or illegible, please call customer service at 1-800-888-8899 for replacements. Apply the labels in the location shown.
HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
ASSEMBLY INSTRUCTION Tools Required for Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended that this machine to be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Attach the Bench Rear Stabilizer (#2) to the Bench Base Frame (#3). B.) Secure them together with two M12 x 3 ¾” Hex Bolts (#49), one 2” x 5 ½” Bracket (#15), four Ø 1” Washers (#54), and two M12 Aircraft Nuts (#52).
STEP 2 (See Diagram 2) A.) Do not tighten all Nuts and Bolts starting from this procedure until instructed to do so. B.) Attach the pivot on the Backrest Support (#4) in the bracket opening on the Main Seat Support (#3). Attach the pivots on the two Seat Supports (#8) to the bracket from each side. Note: The pivots on the Supports need to face upward. C.) Align the holes. Secure them together with one 8 ¼” Axle (#14), two Ø 1” Washers (#54), and two M12 Aircraft Nuts (#52). D.
STEP 3 (See Diagram 3) A.) Slide the Sliding Block (#7) onto the Backrest Incline Adjustment Frame (#5). Attach the pivot on the Sliding Block to the pivot on the Main Seat Support (#3). Secure it with one M12 x 6 1/8” Hex Bolt (#47), two Ø 1” Washers (#54), and one M12 Aircraft Nut (#52). B.) Use the M18 Lock Knob (#16) to hold selected Backrest Incline in position. C.
STEP 4 (See Diagram 4) A.) Attach the Backrest Board (#11) to Backrest Support (#4). Secure it with four M10 x 5/8” Hex Bolts (#45) and four Ø ¾” Washers (#55). B.) Attach the Seat Pad (#10) to the Seat Supports (#8). Secure it with four M10 x 1 5/8” Hex Bolts (#50), and four Ø ¾” Washers (#55). C.) Insert the Front Lock Pin (#13) through the pivot on the Main Seat Support (#3). Secure it with a M10 Aircraft Nut (#53). Thread a M18 Lock Knob (#16) into hole on the Main Seat Support.
STEP 5 (See Diagram 5) A.) Do not tighten Nuts and Bolts until instructed to do so. B.) Connect the two Rack Base Frames (#27) by the Rear Base Frame (#30). C.) Secure each end of Rear Base Frame to a Rack Base Frame with two M12 x 3 3/8” Hex Bolts (#44), one 2 3/8” x 5 1/8” Bracket (#39), four Ø 1” Washers (#54), and two M12 Aircraft Nuts (#52).
10 STEP 6 (See Diagram 6) A.) Do not tighten Nuts and Bolts until instructed to do so. B.) Attach one Front Vertical Frame (#28) to a Rack Base Frame (#27). Secure it from top with two M10 x 5/8” Allen Bolts (#45) and two Ø ¾” Washers (#55). Secure it from side with two M12 x 3 3/8” Hex Bolts (#44), four Ø 1” Washers (#54), and two M12 Aircraft Nuts (#52). C.) Repeat B to install the other Front Vertical Frame on the other side.
11 STEP 7 (See Diagram 7) A.) Do not tighten all Nuts and Bolts until instructed to do so. B.) Attach one Rear Vertical Frame (#29) onto a Rack Base Frame (#27). Secure it from top with two M10 x 5/8” Allen Bolts (#45) and two Ø ¾” Washers (#55). Secure it from side with two M12 x 3 3/8” Hex Bolts (#44), four Ø 1” Washers (#54), and two M112 Aircraft Nuts (#52). C.) Connect the Front and Rear Vertical Frame (#28 & #29) by a Cross Brace (#32).
12 STEP 8 (See Diagram 8) A.) Attach the Chin-up Frame (#31) to the two Rear Vertical Frames (#29). Secure each end with two M12 x 3 3/8” Hex Bolts (#44), one 2 3/8” x 5 1/8” Bracket (#39), four Ø 1” Washers (#54), and two M12 Aircraft Nuts (#52). B.) Securely tighten all Nuts and Bolts installed in Step-5, Step-6, Step-7, and Step-8. C.) Attach the Left & Right Bar Catch (#34 & #33) onto the selected holes on the Rear Vertical Frames. D.
DIAGRAM 8 13 BENCH EXPLODED DIAGRAM
14 RACK EXPLODED DIAGRAM
15 PARTS LIST KEY NO.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 Bench Base Frame Bench Rear Stabilizer Main Seat Support Backrest Support Backrest Incline Adjustment Frame Seat Vertical Support Sliding Block Seat Support Seat Incline Adjustment Frame Seat Pad Backrest Board Seat Incline Lock Pin Front Lock Pin 8 ¼” Axle 2” x 5 ½” Bracket M18 Lock Knob Ø 1” x Ø ½” Bushing Ø 1 ¼” x Ø 5/8” Bushing 1” Square End Cap 1 1/8” x 2 3/8” End Cap 1” x 2” End Cap 2” x 2 ¾
® IMPEX INC. LIMITED WARRANTY ® IMPEX Inc. ("IMPEX ") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX.
